Next Article in Journal
Buildings Energy Efficiency: Interventions Analysis under a Smart Cities Approach
Previous Article in Journal
Minimizing the Carbon Footprint for the Time-Dependent Heterogeneous-Fleet Vehicle Routing Problem with Alternative Paths
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Comprehensive Assessment on Sustainable Development of Highway Transportation Capacity Based on Entropy Weight and TOPSIS

College of Civil Engineering, Hebei University of Engineering, Handan 056038, China
*
Author to whom correspondence should be addressed.
These authors contributed equally to this work.
Sustainability 2014, 6(7), 4685-4693; https://0-doi-org.brum.beds.ac.uk/10.3390/su6074685
Submission received: 17 March 2014 / Revised: 7 July 2014 / Accepted: 17 July 2014 / Published: 23 July 2014
(This article belongs to the Section Sustainable Urban and Rural Development)

Abstract

:
With the rapid development of the national economy of China, an increasing need for transportation facilities is becoming a serious challenge that the existing traffic system has to meet. Thus, the highway transportation capacity development level assessment has important significance in theory and in practice. In order to overcome the current defects of stronger subjectivity and experience in common assessment methods, the entropy weight and the TOPSIS method were introduced and employed to the comprehensive assessment of highway transportation capacity development. Shannon information entropy was applied to determine the weight value of each index in the comprehensive assessment model. After determining the index weight, the result of comprehensive assessment was obtained through the TOPSIS method. Finally, the effectiveness and feasibility of the proposed method were shown by application in practice.

1. Introduction

With the rapid development of the national economy of China, an increasing need for transportation facilities is becoming a serious challenge that the existing traffic system has to meet. Thus, improving traffic capacity has become a vital way of solving traffic problems. Highway transportation plays an important role in today’s economic and social life [1,2,3,4]. It greatly improves and enriches transportation capacity of passengers and cargo due to its strong capacity, high speed and flexible transportation mode [5]. Highway transportation development has a huge impact on economical and social development and becomes a basic condition of various kinds of industry development. Transportation occupies an extremely important position in economic and social development. It should be coordinated with the development of economic and social systems to achieve huge economic and social benefits [6,7,8,9,10,11,12]. At the same time, highway development is also needed intensively when the economy and society develop rapidly in China. A rapid, convenient, comfortable and sustainable transportation network needs to be established urgently alongside economic and social development. The development level shows a developmental status at a time and it reflects the development scale and degree of social economic phenomenon in each period. It is actually one of the specific values in the time series. Through the assessment of the development level of each period, we can know the sustainable development status in all periods and the trend of the development in future, which relates to the sustainability. However, highway transportation is still at a developmental stage in China and a complete and mature transportation system is not established. This will directly restrict the stable development of the Chinese economy and society. So, how best to plan and construct a highway transportation network and realize sustainable development of highway traffic becomes an urgent problem to solve. The comprehensive assessment of highway transportation development becomes an important basis, which evaluates the developmental the pros and cons of an existing highway transportation system. It is playing a vital role in highway transportation development [13]. Currently, many methods and models are applied in the comprehensive assessment of highway transportation development. However, most methods rely on stronger subjectivity and experiences in determining weight value. The objectivity and accuracy of weight value was unavoidably influenced. Thus, the comprehensive assessment results from different researchers are always full of uncertainty. Therefore, we have to find an effective comprehensive method for the assessment of highway transportation development, which has the characteristics of objectivity, simple operation and little interference.
Here, the entropy and the TOPSIS method were employed to the comprehensive assessment of highway transportation development. Shannon information entropy, which is an objective and applicable method for the determination of weight value, was introduced into the comprehensive assessment. It can calculate the weight value of each index more effectively in the comprehensive assessment of highway transportation development. In the application of the Shannon information entropy method, the greater entropy weight indicates a greater variation extent of the relevant index, enabling much more information and having a greater effect. So, the weight value of the corresponding index should also be bigger. In contrast, for the smaller entropy weight, which has little effect, its weight value should be smaller. One of the important contributions of our work is the combined use of entropy weight and TOPSIS, because using only one of these two techniques without the other might lead to unacceptable results.
The structure of this paper is as follows: we first briefly introduce the importance of highway transportation development assessment and clearly point out the advantages of the method employed. Then, the comprehensive assessment model of highway transportation development based on entropy and the TOPSIS method was introduced. In the following part, we focus on the application of the model in practice. Finally, through the application in highway transportation development assessment, the effectiveness and feasibility of the method are shown.

2. Entropy Weight Model

Entropy used to be a thermodynamic concept: it was introduced into information theory in 1948 by C. E. Shannon who put forward the concept of information entropy to measure the level of system chaos or disorder [14,15,16,17,18,19]. Shannon information entropy, which is an objective and applicable method for the determination of weight value, was introduced into the comprehensive assessment. In the application of the Shannon information entropy method, the greater entropy weight indicates greater variation extent of relevant index, which enables much more information and has a greater effect. So, the weight value of the corresponding index should also be bigger. In contrast, for the smaller entropy weight, which has little effect, its weight value should be smaller [17,18].

2.1. Data Standardization

Suppose the research plan is xij (i = 1,2,···n; j = 1,2,···m). It denotes that there are i schemes and j indexes in the research plan. Based on appraisal target characteristics, the indexes are divided into the benefit type, the cost type and stationary indexes. The benefit type indexes are the indexes for which bigger values are better. The cost type indexes refer to the indexes for which smaller values are better. The stationary type indexes are the indexes whose values are constant.
For the benefit type indexes, the standardization is as follows:
Sustainability 06 04685 i001
For the cost type indexes, the standardization is:
Sustainability 06 04685 i002
where, max xij and min xij are the maximum and minimum value in index j respectively.
For the stationary factors, the standardization is:
Sustainability 06 04685 i003
In the formula, Sustainability 06 04685 i004 is the best stable value in index j.
After the standardized processing, the standard matrix y = (yij)n×m can be obtained.

2.2. Determination of Entropy Weight

Suppose the weight vector of targets is:
w = (w1, w2,···, wm) , 0 ≤ wj ≤ 1
In order to determine weight values effectively, Shannon information entropy is introduced:
Sustainability 06 04685 i005
Through the formula of information entropy, it is possible to demonstrate that it is a double plan question. It should be transferred to a single objective mathematics model to make it easily calculable. Then, the established single objective mathematics model is as follows:
Sustainability 06 04685 i006
where, u is the equilibrium coefficient between two goals, and 0 < u < 1.
Then the Lagrangian function was employed to solve this model. The Lagrangian function based on (5) is as follows:
Sustainability 06 04685 i007
After solving (7) based on necessary conditions of existing extreme values, the weight model can be obtained:
Sustainability 06 04685 i008

3. TOPSIS Model

The TOPSIS method (Technique for Order Preference by Similarity to an Ideal Solution) was first proposed by C.L. Hwang and K. Yoon in 1981. It is an ordering method based on the degree of closeness between limited appraisal objects and idealization objects, and it is a kind of relative advantages and disadvantages evaluation in the existing appraisal objects. It is also called the “advantages and disadvantages distance method”. It is an effective method in multi-objective decision analysis [20,21,22,23,24,25]. Its basic principle is to order by calculating distance between appraisal objects and the optimal and worst solutions. If the appraisal objects are close to the optimal solutions, it keeps them away from the worst solutions, which is the best situation.
The ideal point and anti-ideal point are two basic concepts in the TOPSIS method. The ideal point is supposed as the optimal solution, all attribute values of which achieve the best value in all schemes. The anti-ideal point is supposed as the worst solution, all attribute values of which achieve the worst value [24,25].
Supposeis Sustainability 06 04685 i009 the distance between the scheme point and the ideal point, and Sustainability 06 04685 i010 is the distance between the scheme point and anti-ideal point. According to the formula of Hamming distance, Sustainability 06 04685 i009 and Sustainability 06 04685 i010 can be solved as follows:
Sustainability 06 04685 i011
Sustainability 06 04685 i012
where, y+j is maximum value of index j among n assessment schemes and
y+j = max(y1j, y2j,···, ynj)
In contrast, yy is the minimal value of index j among n assessment schemes.
yj = min(y1j, y2j,···, ynj)
In order to compare the distance between the scheme point and double base points, we can define:
Sustainability 06 04685 i015
where, Ti is the relative quality level of the scheme i.

4. Application in Highway Transportation Development Assessment

The comprehensive assessment of highway transportation development becomes an important basis, which evaluates the pros and cons of existing highway transportation systems. It plays a vital role in highway transportation development. In order to show the possibility and effectiveness of the proposed method, the highway transportation development of Luoding City in recent years was viewed as an example. Then the comprehensive assessment model was employed in highway transportation development assessment [26]. Here, highway total mileage (X1), the proportion of city township highway in total mileage (X2), highway freight turnover (X3), highway passenger turnover (X4), motor vehicle population (X5), highway traffic total investment (X6), annual average quality rate of highway (X7), annual daily traffic of national and provincial highway (X8), and the rate of cement highway to administrative villages (X9) were selected as the comprehensive assessment indexes according to the specific conditions of Luoding city traffic development. They are all related to sustainability of highway transportation development. The comprehensive assessment indexes of highway transportation development of Luoding City from 2006 to 2010 were shown in Table 1.
Table 1. Comprehensive assessment indexes of highway transportation development of Luoding City.
Table 1. Comprehensive assessment indexes of highway transportation development of Luoding City.
Assessment indexYears
20062007200820092010
X1 (km)1353.31357.41360.21371.51854.12
X2 (%)83.283.283.383.487.7
X3 (10k ton-km)36,40136,48836,02337,87739,226
X4 (10k passenger-km)120,895121,462114,297116,415121,180
X5 (veh)54326218633065029341
X6 (ten thousand Yuan)104,710110,252103,205127,854134,373
X7 (%)82.190.991.591.592.7
X8 (veh per day)39,24829,85529,46531,05633,891
X9 (%)95.8100100100100
veh: vehicles
The policy-making matrix is:
Sustainability 06 04685 i013
Then, the standard matrix y = (yij)5×9 can be obtained based on policy-making matrix:
Sustainability 06 04685 i014
Here, suppose u = 0.5, according to the formula (8), the weight vector of m targets can be obtained. The weight value of each index is shown in Table 2.
Table 2. Weight value of each index.
Table 2. Weight value of each index.
Assessment indexWeight value
X10.0196
X20.0199
X30.0431
X40.1641
X50.0379
X60.0539
X70.2517
X80.0359
X90.3739
Then, based on the TOPSIS model, the distances between scheme point and double base points can be determined. Relative quality level of the scheme i Ti was shown in Table 3.
Table 3. Relative quality level.
Table 3. Relative quality level.
TiValue
T14.1361
T20.2910
T30.6488
T40.3676
T50.0268
We can obtain the result of comprehensive assessment of highway transportation development of Luoding City according to the table above. The result of comprehensive assessment was shown in Table 4.
Table 4. Result of comprehensive assessment.
Table 4. Result of comprehensive assessment.
YearsOrder of development level
20065th
20072nd
20084th
20093rd
20101st
From Table 4, we can know the highway transportation development conditions of Luoding City in recent years. From 2006 to 2008, the highway transportation development level gradually increased. However, the highway transportation development was lower than the previous year. It simply reflected the actual development situation and conformed the development environment at that time. Since 2009, the highway transportation development level has gradually increased. Moreover, the development level is relatively high. Here, the results of highway transportation development assessment we obtained were in accordance with the results of [21]. The effectiveness and feasibility of the proposed method were shown.

5. Conclusions

The comprehensive assessment of highway transportation development level has important significance in theory and practice. It is also an important basic for realizing the status of highway transportation capacity development. Here, entropy and the TOPSIS method were employed to evaluate objectively and effectively the status of highway transportation capacity development. From the analysis of the assessment indexes, we know that the highway passenger turnover, annual average quality rate of highway, and the rate of cement highway to administrative villages are the three primary factors with higher weight coefficient. Moreover, more attention should be paid to them in future highway traffic development. From the final comprehensive assessment result obtained, we can also assess the highway traffic development status and trend of Luoding city in recent years. The results show that highway traffic of Luoding city has an improved development status. Moreover, with the rapid development of the economy and the increasing investment in highway construction, we can anticipate further positive development in the future. This assessment method can control and guide the development of the highway transportation capacity further. The comprehensive assessment results are acceptable and they showed the effectiveness and feasibility of the method proposed. The study provides an effective method for the assessment of highway transportation development level and the related fields.

Acknowledgments

The work was supported by Natural Science Foundation of Hebei Province, China. (No. E2012402030) and the Program of Selection and Cultivating of Disciplinary Talents of Colleges and Universities in Hebei Province (BR2-206).

Author Contributions

Yancang Li designed research; Lei zhao performed research and analyzed the data; Juanjuan Suo wrote the paper. All authors read and approved the final manuscript.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Amekudzi, A.A.; Khisty, C.J.; Khayesi, M. Using the sustainability footprint model to assess development impacts of transportation systems. Transport. Res. Pol. Pract. 2009, 43, 339–348. [Google Scholar] [CrossRef]
  2. Xiong, Q.; Pu, L.; Yu, M.Y. Analysis of transportation development needs requirement and policy suggestions for road highway transportation in urban agglomeration areas in China. Available online: http://ascelibrary.org/doi/abs/10.1061/9780784413159.179 (accessed on 20 October 2013).
  3. Yi, L.X.; Williams, B.M.; Rouphail, N.M.; Chase, R.T. Development of an oversaturated speed-flow model based on the highway capacity Manual. J. Transport. Res. Board 2013, 2395, 41–48. [Google Scholar] [CrossRef]
  4. Li, H.D.; Zhou, Z.Y. Sustainable development of transportation and design of its index system. Environ. Prot. Transport. 2003, 24, 17–19. (In Chinese) [Google Scholar]
  5. Fricker, J.D.; Whitford, R.K. Fundamentals of Transportation Engineering; Prentice Hall: Upper Saddle River, NJ, USA, 2004. [Google Scholar]
  6. Rephann, T.; Isserman, A. New highways as economic development tools: An evaluation using quasi-experimental matching methods. Reg. Sci. Urban Econ. 1994, 24, 723–751. [Google Scholar] [CrossRef]
  7. Rephann, T.J. Highway investment and regional economic development: Decision methods and economical foundations. Urban Stud. 1993, 30, 437–450. [Google Scholar] [CrossRef]
  8. Roh, H.-J.; Datla, S.; Sharma, S. Effect of Snow, Temperature and Their Interaction on Highway Truck Traffic. J. Transport. Tech. 2013, 3, 24–38. [Google Scholar] [CrossRef]
  9. Weisbrod, G. Models to predict the economic development impact of transportation projects: Historical experience and new applications. Ann. Reg. Sci. 2008, 42, 519–543. [Google Scholar] [CrossRef]
  10. Aschauer, D.A. Highway capacity and economic growth. Econ. Perspect. 1990, 14, 14–24. [Google Scholar]
  11. Shirley, C.; Winston, C. Firm inventory behavior and the returns from highway infrastructure investments. J. Urban Econ. 2004, 55, 398–415. [Google Scholar] [CrossRef]
  12. Berechman, J.; Ozmen, D.; Ozbay, K. Empirical analysis of transportation investment and economic development at state, county and municipality levels. Transportation 2006, 33, 537–551. [Google Scholar] [CrossRef]
  13. Litman, T.; Burwell, D. Issues in sustainable transportation. Int. J. Global Environ. Issues 2006, 6, 331–347. [Google Scholar] [CrossRef]
  14. Liu, P.D.; Han, Z.S. A fuzzy multi-attribute decision-making method under risk with unknown attribute weights. Technol. Econ. Dev. Econ. 2011, 2, 146–258. [Google Scholar]
  15. Ma, L.H.; Kang, S.Z.; Xuan, Y.Q.; Su, X.L.; Solomatine, D.P. Analysis and simulation of the influencing factors on regional water used based on information entropy. Water Policy 2012, 14, 1033–1046. [Google Scholar] [CrossRef]
  16. Chen, T.Y.; Li, C.H. Determining objective weights with intuitionistic fuzzy entropy measures: A comparative analysis. Inf. Sci. 2010, 180, 4207–4222. [Google Scholar] [CrossRef]
  17. Chen, H.T.; Tsutsumi, M.; Yamasaki, K.; Iwakami, K. An impact analysis of the Taiwan Taoyuan international airport access MRT system considering the interaction between land use and transportation behavior. J. East. Asia Soc. Transport. Stud. 2013, 10, 315–334. [Google Scholar]
  18. Liu, L.; Zhou, J.Z.; An, X.L.; Zhang, Y.C.; Yang, L. Using fuzzy theory and information entropy for water quality assessment in three Gorges Region, China. Expert Syst. Appl. 2010, 37, 2517–2521. [Google Scholar] [CrossRef]
  19. Calabrese, F.; Diao, M.; di Lorenzo, G.; Ferreira, J.; Ratti, C. Understanding individual mobility patterns from urban sensing data: A mobile phone trace example. Transport. Res. Emerg. Technol. 2013, 26, 301–313. [Google Scholar] [CrossRef]
  20. Li, P.Y.; Wu, J.H.; Qian, H. Groundwater quality assessment based on rough sets attribute seduction and TOPSIS method in a semi-arid area, China. Environ. Monit. Assess. 2012, 184, 4841–4854. [Google Scholar] [CrossRef]
  21. Torlak, G.; Sevkli, M.; Sanal, M.; Zaim, S. Analyzing business competition by using fuzzy TOPSIS method: An example of Turkish domestic airline industry. Experts Syst. Appl. 2011, 38, 3396–3406. [Google Scholar] [CrossRef]
  22. Soltani, A.; Marandi, E.Z.; Ivaki, Y.E. Bus route evaluation using a two-stage hybrid model of Fuzzy AHP and TOPSIS. J. Transp. Lit. 2013, 7, 34–58. [Google Scholar] [CrossRef]
  23. Janic, M.; Reggiani, A. An application of the multiple criteria decision making (MCDM) analysis to the selection of a new hub airport. Eur. J. Transport Infrastruct. Res. 2002, 2, 113–139. [Google Scholar]
  24. Bu, L.; van Duin, J.H.R.; Wiegmans, B.; Luo, Z.; Yin, C.Z. Selection of city distribution locations in urbanized areas. Soc. Behav. Sci. 2012, 39, 556–567. [Google Scholar] [CrossRef]
  25. Ozceylan, E. A decision support system to compare the transportation modes in logistics. Int. J. Lean Think. 2010, 1, 58–83. [Google Scholar]
  26. Liu, J.B. Evaluation Research of Regional Highway Transportation Development Based on Information Entropy; Press of South China University of Technology: Guangzhou, China, 2011. (In Chinese) [Google Scholar]

Share and Cite

MDPI and ACS Style

Li, Y.; Zhao, L.; Suo, J. Comprehensive Assessment on Sustainable Development of Highway Transportation Capacity Based on Entropy Weight and TOPSIS. Sustainability 2014, 6, 4685-4693. https://0-doi-org.brum.beds.ac.uk/10.3390/su6074685

AMA Style

Li Y, Zhao L, Suo J. Comprehensive Assessment on Sustainable Development of Highway Transportation Capacity Based on Entropy Weight and TOPSIS. Sustainability. 2014; 6(7):4685-4693. https://0-doi-org.brum.beds.ac.uk/10.3390/su6074685

Chicago/Turabian Style

Li, Yancang, Lei Zhao, and Juanjuan Suo. 2014. "Comprehensive Assessment on Sustainable Development of Highway Transportation Capacity Based on Entropy Weight and TOPSIS" Sustainability 6, no. 7: 4685-4693. https://0-doi-org.brum.beds.ac.uk/10.3390/su6074685

Article Metrics

Back to TopTop