Next Article in Journal
Endocytosis Pathways of the Folate Tethered Star-Shaped PEG-PCL Micelles in Cancer Cell Lines
Next Article in Special Issue
Behavior of FRP Bars-Reinforced Concrete Slabs under Temperature and Sustained Load Effects
Previous Article in Journal
Injection Compression Molding of Replica Molds for Nanoimprint Lithography
Previous Article in Special Issue
Nonlinear Analyses of Adobe Masonry Walls Reinforced with Fiberglass Mesh
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

RC Beams Strengthened with Mechanically Fastened Composites: Experimental Results and Numerical Modeling

Department of Civil Engineering, University of Salerno, Via Giovanni Paolo II 132, Fisciano (SA) 84084, Italy
*
Author to whom correspondence should be addressed.
Submission received: 18 December 2013 / Revised: 17 February 2014 / Accepted: 19 February 2014 / Published: 5 March 2014
(This article belongs to the Special Issue Selected Papers from "SMAR 2013")

Abstract

:
The use of mechanically-fastened fiber-reinforced polymer (MF-FRP) systems has recently emerged as a competitive solution for the flexural strengthening of reinforced concrete (RC) beams and slabs. An overview of the experimental research has proven the effectiveness and the potentiality of the MF-FRP technique which is particularly suitable for emergency repairs or when the speed of installation and immediacy of use are imperative. A finite-element (FE) model has been recently developed by the authors with the aim to simulate the behavior of RC beams strengthened in bending by MF-FRP laminates; such a model has also been validated by using a wide experimental database collected from the literature. By following the previous study, the FE model and the assembled database are considered herein with the aim of better exploring the influence of some specific aspects on the structural response of MF-FRP strengthened members, such as the bearing stress-slip relationship assumed for the FRP-concrete interface, the stress-strain law considered for reinforcing steel rebars and the cracking process in RC members resulting in the well-known tension stiffening effect. The considerations drawn from this study will be useful to researchers for the calibration of criteria and design rules for strengthening RC beams through MF-FRP laminates.

1. Introduction

The use of mechanically-fastened (MF) fiber-reinforced polymer (FRP) systems has recently emerged as an effective solution for the flexural strengthening of reinforced concrete (RC) beams. The technique consists of pre-cured FRP laminates with enhanced bearing strength, which can be fastened to the external surface of concrete members through a variety of steel anchors, i.e., nails or powder actuated fasteners (“PAF”), anchor bolts, concrete screws or a combination thereof. Unlike the externally-bonded (EB) FRP method, the MF-FRP system is particularly fit for emergency repairs, where the ease of installation and reversibility are primary requirements; also, it is less vulnerable to fail prematurely by FRP delamination, which abruptly reduces the flexural strength gain and affects the beam ductility.
Figure 1a shows the laminates currently available in the market; they are glass- and carbon-vinyl ester pultruded strips with enhanced transverse and bearing strength by means of embedded fiberglass mats [1]. The width and thickness of the laminates are 102 and 3.2 mm, respectively. They may be pre-drilled with holes at the required fastener spacing to receive fasteners, but they can be easily field drilled or cut into shorter lengths using standard carpenter tools.
Figure 1b depicts the types of anchors used to secure the laminate to concrete. The PAF system consists of pins embedded into base materials by means of a gunpowder charge; the installation requires times shorter than for concrete screw/wedge bolts and wedge anchors. Pre-drilling holes in the concrete is strongly recommended in order to reduce detrimental cracking phenomena. The use of the PAF system is particularly suitable when the compression strength of the concrete is less than 27 MPa. The presence of hard aggregates can prevent the fasteners from fully penetrating the concrete substrate [2].
Figure 1. Components of the mechanically-fastened fiber-reinforced polymer (MF-FRP) system: (a) FRP strip; (b) fasteners.
Figure 1. Components of the mechanically-fastened fiber-reinforced polymer (MF-FRP) system: (a) FRP strip; (b) fasteners.
Polymers 06 00613 g001
Wedge bolts are single-piece, heavy duty anchors that are driven into pre-drilled holes. Driving of the wedge bolt can be performed with a common rotary drill or impact wrench. As for the PAFs, the efficiency of wedge bolts is dependent on the presence of hard aggregates. Preliminary studies [3] indicate that this use is not recommended for concrete with a compression strength greater than 27 MPa and with hard aggregates in the mix design.
In spite of longer installation times, wedge anchors can be used for any type of concrete; they are driven through the laminate into predrilled holes until the nut and washer are firmly secured against the laminate. The anchors are typically tightened by turning the nut with an electrical drill with torque control, according to the specifications of fastener manufactures.
A recently published state-of-the-art review of the experimental research has provided compelling evidence of the effectiveness and viability of using MF-FRP laminates to rehabilitate RC beams and slabs [4]. It has shown that with an appropriate fastener layout and FRP laminate properties, the strength increases are comparable to those of EB-FRP-strengthened members, but with greater displacements exhibited at collapse. Furthermore, experimental tests have proven that the mechanically-fastened composite system is an effective technique for improving the flexural capacity of corrosion-damaged RC beams [5]. Finally, applications of the MF-FRP technique to wood and timber structural members have been reported [6,7].
Several analytical and numerical studies have been carried out throughout-years with the aim of predicting the behavior of RC members strengthened in bending with MF-FRP systems: a state-of-the-art review on this topic has been recently published by Napoli et al. [8]. As highlighted therein, the first analytical models were based, for the sake of simplicity, on the hypothesis of the “conservation of plane sections” between the concrete and the FRP, as generally accepted for EB-FRP-strengthened members. Despite their ease of application, such models have often provided inaccurate predictions which were primarily attributed to ignoring the slip between the concrete and FRP strip. Therefore, novel proposals accounting for the concrete-FRP interfacial behavior were recently formulated by Lee et al. [9] and Nardone et al. [10]. In particular, Lee et al. [9] experimentally calibrated a reduction factor for the FRP strain estimated by assuming a perfect bond (no slip). Nardone et al. [10], instead, modeled the slip by means of a linear function of the position along the longitudinal axis of the FRP laminate, with a maximum value at the first fastener and zero slip at midspan for the case of symmetric loads.
Finite-element (FE) models were also developed to simulate the behavior of MF-FRP-strengthened RC beams and slabs. To this aim, the first work Napoli et al. [11] formulated a FE procedure in which a continuous connection was assumed throughout the interface between the FRP laminate and RC beam, in spite of the discrete nature of mechanical anchors. Although this assumption led to results as accurate as in the case of EB-FRP systems, it introduced a certain level of approximation, especially in the case of either coarse or unequally-spaced fasteners. Thus, the authors have recently developed a novel FE model which is based on the explicit assumption of discrete connection between concrete and FRP. Such a model, already detailed and validated in Martinelli et al. [12], is used in this study to simulate experimental tests available in the literature and relative to MF-FRP-strengthened RC beams and one-way slabs; most of these tests are included in a more general database published by Brown et al. [4].
The numerical simulations discussed herein were mainly aimed at investigating the influence of some specific aspects on the structural response of MF-FRP-strengthened members, such as the bearing stress-slip relationship assumed for the FRP-concrete interface, the stress-strain law considered for reinforcing steel rebars and the cracking process in RC members, which is often disregarded in modeling methods. The considerations drawn from this study will be useful to researchers for the calibration of criteria and design rules for the strengthening RC beams through MF-FRP laminates.

2. Outline of the Proposed 1D-FE Model

This section presents the key features of the novel 1D finite-element model formulated for simulating the flexural behavior of RC beams strengthened by MF-FRP. Such a model, deeply described in [12], is based on a discrete connection between the RC beam and the FRP strip, and can be potentially used for analyzing other similar modeling problems, such as those related to the external reinforcement of masonry or wood members.

2.1. Assumptions and Formulation of the Finite Element

The proposed finite element is obtained by assembling the following three components (see Figure 2):
-
a 1D element that represents the behavior of Euler–Bernoulli’s RC beam;
-
a rod element that simulates the mechanical behavior of an FRP laminate;
-
two springs that simulate the behavior of the fasteners and are only translational in the direction of the beam axis.
Figure 2. Key components of the proposed 1D finite-element.
Figure 2. Key components of the proposed 1D finite-element.
Polymers 06 00613 g002
The relevant displacement and force components of the finite element “e”, whose nodes are labelled as “a” and “b” are collected in the two following vectors u(e) and f(e), respectively, and represented in Figure 3:
Polymers 06 00613 i001
By introducing the stiffness matrix, k(e), of the finite element “e” and the vector of equivalent nodal forces, f0(e), the following matrix relationship between vectors u(e) and f(e) can be written:
f(e) = k(e) u(e) + f0(e)
The matrix, k(e), and the vector f0(e), can be both determined by taking into account the contributions corresponding to the three abovementioned components (beam, rod and springs). Details about the model formulation are omitted herein for the sake of brevity and can be found in [12].
Figure 3. Force and displacement components for the proposed finite element.
Figure 3. Force and displacement components for the proposed finite element.
Polymers 06 00613 g003

2.2. Nonlinear Analysis Procedure

RC beams with MF-FRP plates can be discretized through the n aforementioned finite elements, and the following relevant assumptions have been implicitly considered:
-
the flexural stiffness of the FRP laminate is neglected, and only the axial one is considered;
-
equal vertical displacements occur in the connected RC slab and FRP laminate elements;
-
shear deformations of the RC slab are neglected.
The generic finite element is then used for nonlinear analyses through a fiber discretization of the beam cross-section and by implementing an iterative convergence procedure based on the “tangent” value approach to account for material nonlinearity, including concrete, steel and the concrete–FRP interface, as already demonstrated for the case of EB-FRP-strengthened RC members [13].
Figure 4 and Figure 5 depict the generalized stress-strain laws considered in the numerical analyses to simulate the behavior of concrete in compression [14] and tension [15] and of steel rebars, respectively, whereas the FRP strip was simulated through an elastic-brittle behavior.
Figure 4. Stress-strain law for concrete.
Figure 4. Stress-strain law for concrete.
Polymers 06 00613 g004
Figure 5. Alternative stress-strain laws for steel reinforcing bars: “accurate” (a) and “simplified” (b) bilinear models.
Figure 5. Alternative stress-strain laws for steel reinforcing bars: “accurate” (a) and “simplified” (b) bilinear models.
Polymers 06 00613 g005
As shown in Figure 5, two stress-strain (σss) relationships have been taken into account for simulating the behavior of steel rebars. The first one (Figure 5a) is characterized by an initial elastic behavior, a yielding phenomenon with constant stress and, then, by a hardening response; particularly, a parabolic branch was considered after the yielding plateau, which was assumed to develop up to the hardening strain, εsu. The elastic-plastic σss law of Figure 5b, instead, is of a bilinear type and represents a possible simplification of the more accurate relationship shown in Figure 5a. It is highlighted that in the numerical analyses, the values of εsh, εsu and ultimate strength (ft) were always assumed equal to 0.003, 0.07 and 1.20 fy, respectively, where fy is the yield strength of longitudinal steel rebars. More details about the considered stress-strain laws can be found in [12].
Figure 6, instead, shows the bearing stress-interface slip (σf-s) relationships employed to simulate the response of the connecting devices, i.e., of shot or screwed fasteners. In particular, the trilinear laws selected in the case of screws with (w/) and without (w/o) washers (Models 2b and 3 in Figure 6) are those proposed by the authors in a previous study [16]; the other ones, used in the case of shot or screwed fasteners w/ washer (Models 1 and 2a in Figure 6), are those found by Elsayed et al. [17].
Figure 6. Bearing stress-slip relationship describing the FRP strip-concrete interaction.
Figure 6. Bearing stress-slip relationship describing the FRP strip-concrete interaction.
Polymers 06 00613 g006
It is highlighted that although three of the four σf-s laws exhibit a softening branch, the actual values of the interfacial slip observed in the modeling of the MF-FRP-strengthened beams never fall in such a branch; therefore, modeling issues related to strain localization can be overcome.
A nonlinear solution procedure can be implemented to determine the response of the structural system under self-weight and other external loads. First of all, the distributed loads corresponding to the beam self-weight are applied in force control, and then, the procedure works in the displacement control for simulating the effect of the imposed external loads. The analysis foresees several steps of imposed displacement increments and, in each step, an iterative search of the forces corresponding to the imposed displacement. In particular, at the i-th analysis step, the j-th iteration firstly provides an “elastic prediction” of the solution, based on the tangent stiffness matrix KT,i(j − 1), at the end of the previous iteration:
∆Uel,i(j) = [KT,i(j-1)]-1 ∆λel,i(j)Fq
where ∆λel,i(j) is the current value of the elastic incremental force multiplier, Fq is a global vector describing the “shape” of the external load applied to the beam and ∆Uel,i(j) is the vector of the elastically predicted displacement increments (at the j-th iteration of the i-th load step).
Equation (3) can be solved through classical numerical procedures of the finite element modeling (FEM) based on imposing that one of the ∆Uel,i(j) components (i.e., the mid-span deflection) is equal to the controlled displacement increment ∆wi(j).
For each element, the local displacement increment ∆uel,i(j), can be obtained through ∆Uel,i(j), and then, the elastic prediction of the j-th iteration can be completed by determining both the local stress increment ∆σel,i(j), and the corresponding local strain vector, εel,i(j).
Then, the “plastic correction” can be performed by evaluating the stress increments, ∆σpl,i(j), actually corresponding to the current strain increments, εel,i(j)εel,i-1, where the latter is the strain vector at convergence of the (i − 1)-th analysis step. The “plastic correction” ends as the nonlinear stress increment, ∆σpl,i(j), is determined and the corresponding stiffness matrix is updated by considering the actual nonlinear response of the three components mentioned in Subsection 2.1.
At the end of this sub-step and after having assembled the new local stiffness matrices, kT,i(j), the global tangent matrix, KT,i(j), and the corresponding external force increment, ∆Fpl,i(j), can be obtained:
∆Fpl,i(j) = KT,i(j) ∆Uel,i(j)
Then, the (j + 1)-th iteration can be carried out for determining the force and displacement increment according to a relationship similar to Equation (3). The iteration procedure proceeds for the current analysis step, until two following iterations yield displacement increments, whose difference is the smaller of a given tolerance δ:
Polymers 06 00613 i002
At the end of the i-th analysis step, the failure conditions of both materials (possibly achieving the ultimate strain) and fasteners (possibly attaining the ultimate slip value) should be checked. If either of such materials or one of the fasteners achieves such a conventional failure condition, the analysis finishes; otherwise the analysis proceeds with the (i + 1)-th step, as described above.

3. The Database

A wide database was assembled from the literature, which collects a total of 93 four point-bending tests performed on RC beams/slabs externally strengthened with MF-FRP laminates. Figure 7 shows a schematic of the tests under consideration. It is highlighted that the considered database represents a further updating of that which was recently published in [12].
Figure 7. The configuration of four point-bending tests collected from the literature.
Figure 7. The configuration of four point-bending tests collected from the literature.
Polymers 06 00613 g007
Table 1 summarizes the relevant geometrical and mechanical properties of the test specimens and the experimental load values measured at yielding and peak conditions. Table 2, instead, provides information about the MF-FRP strengthening layouts.
In addition to the symbols clarified in Figure 7, the other labels included in Table 1 and Table 2 are reported in the following:
-
fc = average value of concrete cylinder compressive strength;
-
fy = average value of yield strength of longitudinal steel reinforcement, when obtained by tensile tests (alternatively, information about the steel grade is provided);
-
Fy = experimental value of the force measured at the beam yielding during the test;
-
Fmax = experimental value of the peak force measured during the test;
-
Lf, Ef, ff = length, elastic modulus and tensile strength of the employed FRP strip, respectively;
-
da, La = diameter and shank length of the employed fasteners (shot, screw or wedge), respectively, which were provided or not with steel washer.
The fasteners were arranged on single or multiple rows (N = 1, 2, 4) according to aligned (“-a”) or staggered (“-s”) configurations or combinations thereof (“a-s”).
As observed from the tables, test specimens have different sizes of cross-section, with values of the height-to-width (h/b) ratios spanning from 0.5 (“slab-type”) to 1.67 (“beam”-type”); the clear lengths range from 1067 mm (small-scale members) to 3505 mm (large-scale members).
Table 1. The geometry and mechanical properties of considered test specimens and main results.
Table 1. The geometry and mechanical properties of considered test specimens and main results.
SourceTestLcLsb × hAsAsdfcSteel typeFy 1Fmax 1
(mm)(mm)(mm2)(mm2)(mm2)(mm)(MPa)fy (MPa) KNKN
Borowicz (2002) [18]U-W-235051372305 × 30514310135144.7Grade 60186210
U-W-42134686377427
U-W-52642940268344
U-W-633531295193243
U-W-734541346185234
U-W-835051372182233
U-W-935051372202257
Ebead (2011) [19]M-F-D10-12250850150 × 25010115725415405170
M-F-D10-215725385407077
M-F-D12-122626385507999
M-F-D12-2226263955075105
M-F-D16-14022840530106130
M-F-D16-24022839530110132
M-P-D10-115725375404455
M-P-D10-215725385403960
M-P-D12-122626365506879
M-P-D12-222626395506881
M-P-D16-14022836530101105
M-P-D16-24022841530-110
Ekenel et al. (2005) [20]S-4-F1829304254 × 1651432144527.64145772
El-Maaddawy (2013) [5]C0-PAF-3228001200250 × 2753391003430.550085122
C0-PAF-5285134
C0-EAB90132
C0-TAB90135
C1-PAF-328095
C1-PAF-5280109
C1-EAB85125
C1-TAB85129
C2-PAF-327584
C2-PAF-527587
C2-EAB75110
C2-TAB75128
El-Maaddawy et al. (2013) [21]C0-F50-321250550150 × 21022610030325388086
C0-F100-328587
C0-F100-32-28588
C0-F50-528594
C0-F100-528590
C1-F50-328090
C1-F100-328087
C1-F100-32-28088
C1-F50-528090
C1-F100-527081
C2-F50-327080
C2-F100-327581
C2-F100-32-28084
C2-F50-527076
C2-F100-527078
C3-F50-526574
C3-F100-527083
Galati et al. (2007) [22]M-F-P-22200600200 × 2502262262931.546287131
Lamanna (2002) [23]D-11168483153 × 1531432545042Grade 605261
D-21168483425258
E-11168483425155
E-21168483425161
J-11168483425054
L-11067432425556
T-11067432425662
T-21067432425967
T-31067432425461
F-11168483214852
G-11168483214950
K-11168483214750
M-11067432215355
N-11067432215757
P-11067432216062
Q-11067432215656
R-11067432215662
R-21067432215659
U-11067432215355
Lamanna et al. (2001) [24]F-42-S-102-1R1067432153 × 1531432543942Grade 605967
F-21-S-102-2R215659
Bank et al. (2002) Lamanna et al.(2004) [25,26]S-4-Y-AL3233531118305 × 30514310135135.3Grade 60225255
I-4-N-AL32233253
I-4-Y-AL32239269
I-4-Y-AL32-R234279
I-8-Y-AL32248273
H1.5-4-YAL32249262
H1.5-4-Y-AL42D244273
H1.5-4-Y-AL47D249293
H1.5-4-Y-AL47D-3249285
H1.5-4-Y-AL47D-3R249283
H1.5-8-Y-AL32266266
H1.0-4-Y-AL47D-5219243
Lee et al. (2007) [27]11370610200 × 1501572264034.5Grade 607984
21370610200 × 1501572264034.5Grade 607892
Martin and Lamanna (2008) [28]6-L33531219305 × 30514310135148Grade 60185203
6-S196211
10-L182206
12-L192213
Napoli et al. (2008) [11]MF-1-L30481219305 × 152-3802526.7Grade 604261
MF-1-S4156
MF-2-L3656
MF-2-S3550
Note: 1 The experimental values indicated in the published papers are reported in italics, whereas the remaining results have been approximately found by the authors.
Table 2. Details on the strengthening layouts. N-a, aligned; -s, staggered.
Table 2. Details on the strengthening layouts. N-a, aligned; -s, staggered.
SourceTestbftfLfEfffFastener typedaLaWasher# rows
(mm)(mm)(mm)(GPa)(MPa)(mm)(mm)
Borowicz (2002) [18]U-W-21023.2340456.5494PAF4.547YES2-a
U-W-421344942-a
U-W-526424942-a
U-W-632517432-a
U-W-730487432-a
U-W-829977432-a
U-W-96.434047432-a
Ebead (2011) [19]M-F-D10-11023.22200721003Screw4.7637YES2-a
M-F-D10-222001-a/2-a
M-F-D12-122002-a
M-F-D12-222001-a/2-a
M-F-D16-122002-a
M-F-D16-222001-a/2-a
M-P-D10-113502-a
M-P-D10-213501-a/2-a
M-P-D12-113502-a
M-P-D12-213501-a/2-a
M-P-D16-113502-a
M-P-D16-213501-a/2-a
Ekenel et al. (2005) [20]S-4-F1023.2177862531Wedge anchor9.540.3YES1-s
El-Maaddawy (2013) [5]C0-PAF-321023.2260062852PAF432NO2-a
C0-PAF-52PAF452NO2-a
C0-EABWedge855YES1-s
C0-TABScrew855NO1-s
C1-PAF-32PAF432NO2-a
C1-PAF-52PAF452NO2-a
C1-EABWedge855YES1-s
C1-TABScrew855NO1-s
C1-PAF-32PAF432NO2-a
C1-PAF-52PAF452NO2-a
C1-EABWedge855YES1-s
C1-TABScrew855NO1-s
El-Maaddawy et al. (2013) [21]C0-F50-32513.2105062852PAF432NO1-a
C0-F100-32102321-a
C0-F100-32-2102322-a
C0-F50-5251521-a
C0-F100-52102521-a
C1-F50-3251321-a
C1-F100-32102321-a
C1-F100-32-2102322-a
C1-F50-5251521-a
C1-F100-52102521-a
C2-F50-3251321-a
C2-F100-32102321-a
C2-F100-32-2102322-a
C2-F50-5251521-a
C2-F100-52102521-a
C3-F50-5251521-a
C3-F100-52102521-a
Galati et al. (2007) [22]M-F-P-21023.2210062835Wedge anchor12100YES1-s/2-a
Lamanna (2002) [23]D-11023.2111713.8232PAF422YES2-a
D-2111713.82324222-a
E-1111713.82324222-a
E-2111713.82324222-a
J-1111713.82323.7271-a
L-1101613.82324.5321-a
T-1101613.82323.7321-a
T-2101613.82323.7321-a
T-3101613.82323.7321-a
F-1111713.82323.7271-a
G-1111713.82323.7272-a
K-1111713.82323.7321-a
M-1101613.82323.7321-a
N-1101617.03513.7321-a
P-16.4101615.52043.7271-a
Q-13.2101627.35613.7321-a
R-1101613.82323.5272-a
R-2101613.82323.5272-a
U-151101613.82323.7321-a
Lamanna et al. (2001) [24]F-42-S-102-1R1023.2101613.8232PAF3.527YES2-a
F-21-S-102-2R3.7321-a
Bank et al. (2002) Lamanna et al.(2004) [25,26]S-4-Y-AL321023.2304815.2325PAF4.532YES2-a
I-4-N-AL3210226.3695322-a
I-4-Y-AL3210226.3695322-a
I-4-Y-AL32-R10226.3695322-a
I-8-Y-AL3220426.3695324-a
H1.5-4-YAL3210257.2828322-a
H1.5-4-Y-AL42D10257.2828422-a
H1.5-4-Y-AL47D10257.2828472-a
H1.5-4-Y-AL47D-310257.2828472-a
H1.5-4-Y-AL47D-3R10257.2828472-a
H1.5-8-Y-AL3210257.2828324-a
H1.0-4-Y-AL47D-510256.9916472-a
Lee et al. (2007) [27]11023.2137068.3848PAF3.525YES2-a
21023.2137068.3848PAF3.532YES2-a
Martin and Lamanna (2008) [28]6-L1023.2325157.7805Screw12.750.8YES1-a
6-S1-s
10-L1-a
12-L1-a
Napoli et al. (2008) [11]MF-1-L1023.2271862852Screw9.544.5NO1-s
MF-1-S21081-s
MF-2-L27181-s
MF-2-S24131-s
The concretes used for producing members are characterized by medium-high values of the compressive strength, fc, which can have an influence on the strengthening performance.
The laminates employed for the MF-FRP system have different mechanical properties, determined by mainly varying the combinations of carbon/glass fibers and the amount of embedded fiberglass mats adopted for their manufacturing.
As observed, the mechanical fastening mostly consists of shot fasteners (namely “PAF”), with diameters ranging from 3.5 to 4.5 mm and lengths from 22 to 52 mm.
Screw anchors were also frequently used, for which the diameters span from 4.76 to 12.7 mm and the lengths from 37 to 55 mm. Only in a few cases, instead, the mechanically fastening was performed by using wedge anchors [5,20,22]; in [20,22], they were installed into the concrete by using epoxy resin as a gap filler. In the case of the specimen M-F-P-2 [22], the FRP laminate was both bonded and mechanically fastened to the concrete substrate. In the case of the specimen S-4-F [20], instead, which was pre-cracked prior to being strengthened with the MF-FRP strip, the use of wedge anchors was coupled with end anchor spikes; also, such a member was subjected to a cyclic test unlike the other 92 tests, all monotonic.

4. Application of the FE Model

The FE model has been used for performing numerical simulations of experimental tests collected in the database of Table 1 and Table 2. As already mentioned, these analyses were mainly devoted to investigate some specific aspects of the structural response, which may have a varying significance in the modeling of MF-FRP-strengthened beams. In particular, the influence of the following aspects was explored:
(a)
uncertainty on the actual mechanical properties of steel rebars and mainly on the fy value, which is not always provided in the literature papers, and the choice of the stress-strain law to use for simulating the response of such rebars;
(b)
selection of the bearing stress-slip interface law to model the effect of the partial interaction between concrete and FRP laminate; and
(c)
the cracking process in RC members, related to the different tensile response of concrete, which is generally neglected in modeling methods.
The authors highlight that the numerical analyses have been carried out for all beams listed in Table 1, but, for the sake of brevity, only some of the most representative ones have been chosen in the paper. Furthermore, in order to better show the effect of the three considered parameters on a specific beam, the test, MF-1-L [11] has been selected herein.

4.1. Influence of Mechanical Properties and Stress-Strain Behavior of Steel Rebars

As shown in Table 1, many papers do not provide the actual mechanical properties of the used rebars, as obtained by tensile tests, but only indicate the denomination of the employed steel according to the American Society for Testing and Materials (ASTM) specifications. Thus, some mismatches between experiments and predictions may be related to uncertainties on the steel rebars’ properties and mainly on the yield strength value, fy.
Figure 8a,b depicts the numerical simulations obtained for three tests, namely P-1 [23], -1 and -2 [27]. For these analyses, the behavior of the steel rebars was modeled according to the stress-strain relationship of Figure 5a and by plugging two alternative values of the yield strength, i.e., fy = 420 MPa, which is the lowest strength attributable to Grade 60 steel and a slightly increased value equal to 475 MPa; then, an ultimate strength ft = 1.2· fy was always considered. In these tests, the concrete-FRP interface was modeled through the σf-s law proposed by Elsayed et al. [17], i.e., Model 1 of Figure 6 which is the only one available for the case of shot fasteners; the tension stiffening effect was taken into account by considering C = 1 in Equation (6).
Figure 8. Influence of the mechanical properties (a,b,e) and stress-strain law (c,d,f) of steel rebars.
Figure 8. Influence of the mechanical properties (a,b,e) and stress-strain law (c,d,f) of steel rebars.
Polymers 06 00613 g008
The comparisons of Figure 8a,b highlight the good accuracy of the performed modeling, thus implying that uncertainties on the steel rebars’ properties are well covered by the range chosen for fy. In fact, for the test, P-1, the numerical simulation obtained by considering fy = 420 MPa reproduces the experimental curve well in terms of initial stiffness but underestimates the flexural response at the peak condition; conversely, the numerical curve resulting from fy = 475 MPa approximates the post-yield behavior better. By looking at the plot of Figure 8b, instead, it is noted that each numerical simulation accurately reproduces one of the two experimental curves; such curves differ from each other for the length of the used fastener (La = 25 or 32 mm).
A further aspect of interest in the modeling of the steel rebars’ behavior deals with the approximation level achieved when the elastic plastic stress-strain law (Figure 5b) is used in place of the more accurate one shown in Figure 5a. To this aim, the experimental-numerical comparisons shown in Figure 8c,d can be observed, which were obtained for specimens U-W-8 [18] and T-1 [23]. As for the tests P-1, -1 and -2, the behavior of the FRP–concrete interface was modeled through the σf-s law proposed by Elsayed et al. [17] for the case of “PAF” systems. As expected, Figure 8c,d confirms a rather slight dependence of the numerical curves on the model type used for steel rebars; therefore, the elastic-plastic law can be successfully chosen for the simulations of all tests.
The low influence of mechanical properties and the stress-strain behavior of steel rebars can be finally verified by observing the experimental-numerical comparisons in Figure 8e,f, obtained for specimen MF-1-L [11]. In this test, the behavior of the FRP-concrete interface was modeled through the σf-s law proposed by Realfonzo et al. [16] and suitable for fasteners w/o washers (i.e., Model 3 in Figure 6); the tension stiffening effect was taken into account by considering C = 1 in Equation (6). As shown, the post-yield behavior of the experimental curve is better simulated by considering fy = 475 MPa in the numerical analysis, whereas no appreciable influence is noted by changing the stress-strain model for steel rebars.

4.2. Influence of the Bearing Stress–Slip Interface Law

As mentioned earlier, Elsayed et al. [17] and Realfonzo et al. [16] recently proposed nonlinear bearing stress–slip models to describe the effect of the partial interaction between the concrete and the FRP laminate. These models, depicted in Figure 6, were experimentally calibrated through direct shear (DS) tests performed on MF-FRP/concrete joints with a single connector.
In particular, among the proposals by Elsayed et al., one model was found from joints having a shot fastener with a 47-mm shank length, a 3.7-mm shank diameter and a 13-mm washer; the other one, instead, was defined for a screwed fastener with a 37-mm shank length, a 4.8-mm shank diameter and a 16-mm washer.
The trilinear models proposed by Realfonzo et al. were found from a screwed fastener w/ or w/o washer; the screw adopted in the DS tests had a 45-mm shank length, a 6-mm shank diameter and a 32-mm washer (when used).
Comparisons between experimental and numerical force-deflection curves are shown in Figure 9, which allow one to better investigate the sensitivity of the structural response with the use of different bearing stress–slip relationships. It is highlighted that in these tests, the tension stiffening effect was taken into account by considering C = 1 in Equation (6).
Figure 9. Influence of the bearing stress-slip interface law: numerical simulations of tests by Ebead [19] (ad) and Napoli et al. [11] (eh).
Figure 9. Influence of the bearing stress-slip interface law: numerical simulations of tests by Ebead [19] (ad) and Napoli et al. [11] (eh).
Polymers 06 00613 g009
In the plots of Figure 9a–d, obtained for some tests performed by Ebead [19], the behavior of the screws w/ washer was modeled by using the respective σf-s laws provided by Elsayed et al. (“Elsayed model”) and Realfonzo et al. (“Trilinear model”), i.e., Models 2a and 2b in Figure 6. As observed, both simulations well reproduce the initial stiffness of the experimental curves, since the two bearing stress-slip models overlap each other for low values of interfacial slips (Figure 6). Then, increasing the relative displacement between the concrete and FRP strip, a greater force per fastener is calculated with the trilinear σf-s law which in turn leads to overestimating of the flexural strength of the beams. Thus, although differences between the two simulations are rather negligible, the numerical predictions obtained by assuming the “Elsayed model” better predict the three experimental curves; this evidence may be partially justified by the fastener type used in the tests by Ebead [19], which is the same employed by Elsayed et al. [17] in the DS tests.
In Figure 9e–h, the behavior of screws w/o washer in tests by Napoli et al. [11] was modeled by using Model 3 in Figure 6 by Realfonzo et al. [16] and, for comparison, Model 1 by Elsayed et al. [17], though suitable for fasteners w/ washer. Furthermore, in order to better highlight how the use of a proper bearing stress-slip law improves the fitting of the experimental results, in Figure 9g,h the results of numerical simulations obtained by implementing a “no-slip” model of the MF-FRP connection are reported.
In the case of tests MF-1-S and MF-1-L, the plots show a very good agreement between experimental results and numerical predictions, which are rather accurate in simulating the cracking onset in concrete and yielding in steel rebars. In the cases of tests MF-2-L and MF-2-S, the numerical responses before steel yielding are characterized by a slightly greater stiffness with respect to the experimental ones. In all cases, since small values of interfacial slips are activated for these members, the numerical simulations do not significantly change with the use of the two σf-s relationships, thus implying that both of them are suitable for modeling MF-FRP-strengthened slabs.

4.3. Influence of the Tension-Stiffening Effect

The simulation of the cracking processes of RC members is a challenging issue, especially in the case of 1D numerical models. Such processes are characterized by the onset of cracking in concrete subjected to tensile stresses: since the actual tensile strength of concrete is generally affected by significant levels of randomness, the prediction of the cracking onset is often a critical issue. Furthermore, the well-known tension-stiffening effect significantly influences the flexural response of RC members in the post-cracking stage.
As mentioned earlier, since the present proposal is based on a continuous (smeared) crack FE model, the tension stiffening effect has been simulated by a conventional softening branch in the tensile stress-strain law of concrete, which is expressed by the following equation [15]:
Polymers 06 00613 i003
where fct is the nominal tensile strength, Ect the Young modulus of concrete in tension and C a conventional exponent controlling the post-peak softening branch of concrete.
It is worth highlighting that the shape of the post-peak tensile branch strongly depends on the values of the C exponent in Equation (6). Since this exponent is intended at a “material level” simulation of the tension-stiffening effect (which is rather a structural effect), no constitutive correlation can be figured out for C, but its value should be calibrated depending on the geometric and mechanical properties of the RC member under consideration. In this study, the tension stiffening effect is investigated by considering three fairly different values of such a C exponent, spanning over a range from 0.5 to 50 and covering tensile behaviors of concrete from rather resilient (C = 0.5) to very brittle (C = 50).
Figure 10 shows the resulting numerical simulations for some tests reported in [11,18,23,25,26]. It is highlighted that the behavior of fasteners has been simulated by using: Model 1 by Elsayed et al. [17] for tests U-W-6 and T-1; the trilinear σf-s Models 2b and 3 by Realfonzo et al. [16] for test M-F-1-L and I-4-N-AL32, respectively.
Figure 10. Influence of the tension-stiffening effect: numerical simulations of tests by Borowicz [18] (a); Lamanna [23] (b); Napoli et al. [11] (c); Bank et al. and Lamanna et al. [25,26] (d).
Figure 10. Influence of the tension-stiffening effect: numerical simulations of tests by Borowicz [18] (a); Lamanna [23] (b); Napoli et al. [11] (c); Bank et al. and Lamanna et al. [25,26] (d).
Polymers 06 00613 g010
Observing these plots, it is noted that the effect of a different tensile response of concrete is particularly relevant in terms of flexural stiffness in the post-cracking regime. However, a lower tension-stiffness effect (simulated by assuming C = 50) has an influence on the bending moment of the beam at yielding. Particularly, it results in the most accurate simulations in terms of initial stiffness when shot fasteners are used (see Figure 10a,b,d). In fact, the installation of such a connector type generally induces significant pre-cracking in the concrete, which is well reproduced by a lower contribution of the tension-stiffening effect.

5. Conclusions

A finite element model was developed and used by the authors to simulate the flexural behavior of RC beams externally strengthened by mechanically fastened FRP laminates.
Several numerical analyses were carried out by using experimental results collected in a wide database assembled from the literature. Such analyses were aimed at investigating the influence of some specific aspects on the structural response of MF-FRP strengthened members, such as stress-strain laws implemented for steel rebars, bearing stress-slip laws assumed for the FRP-concrete interface and the cracking process, with emphasis on the tension stiffening effect developing in RC members.
From the experimental-numerical comparisons, the following considerations were drawn and can be generalized in the modelling of MF-FRP-strengthened members:
(a)
as expected, a rather slight dependence of the performed analyses on the stress-strain model used for steel rebars is observed; thus, a simplified elastic-plastic law can be successfully chosen in the simulation of tests;
(b)
since small values of interfacial slips are activated in the case of MF-FRP-strengthened beams, the numerical simulations do not significantly change with the use of two different bearing stress-slip relationships, thus implying that both of them are suitable in the modeling of these members;
(c)
the use of a lower tension-stiffening effect has an influence on the bending moment of the beam at yielding and provides the most accurate simulations in terms of initial stiffness when shot fasteners are used. In fact, the installation of such a connector type generally induces significant pre-cracking in the concrete, which is well reproduced by a lower contribution of the tension-stiffening effect. For the case of fastening with concrete screws or wedge anchors, instead, the implementation of the tension-stiffening effect with the C exponent equal to one generally provides the most accurate simulation of the experimental results.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Strongwell. 2010. Available online: http://www.strongwell.com (accessed on 27 January 14).
  2. Bank, L.C. Mechanically-Fastened FRP (MF-FRP)—A Viable Alternative for Strengthening RC Members. In Proceedings of the FRP Composites in Civil Engineering (CICE 2004), Adelaide, Australia, 8–10 December 2004.
  3. Rizzo, A.; Galati, N.; Nanni, A.; Bank, L.C. Strengthening Concrete Structures with Mechanically Fastened Pultruded Strips. In Proceedings of the Composites 2005, Columbus, OH, USA, 28–30 September 2005.
  4. Brown, V.L.; Bank, L.C.; Arora, D.; Borowicz, D.T.; Godat, A.; Lamanna, A.J.; Lee, J.; Matta, F.; Napoli, A.; Tan, K.H. Experimental studies of mechanically-fastened FRP systems: State-of-the-art. In ACI Special Publication SP-275-48, Proceedings of the FRPRCS-10, Tampa Bay, FL, USA, 2–4 April 2011; pp. 841–886.
  5. El-Maaddawy, T. Mechanically fastened composites for retrofitting corrosion-damaged reinforced-concrete beams: Experimental investigation. J. Compos. Constr. 2013. [Google Scholar] [CrossRef]
  6. Dempsey, D.D.; Scott, D.W. Wood members strengthened with mechanically fastened FRP strips. J. Compos. Constr. 2006, 10, 392–398. [Google Scholar] [CrossRef]
  7. Schorer, A.E.; Bank, L.C.; Oliva, M.G.; Wacker, J.P.; Rammer, D.C. Feasibility of Rehabilitating Timber Bridges Using Mechanically Fastened FRP Strips. In Proceedings of the ASCE SEI Structures 2008 Conference, Crossing Borders, Vancouver, BC, Canada, 24–26 April 2008.
  8. Napoli, A.; Bank, L.C.; Brown, V.L.; Martinelli, E.; Matta, F.; Realfonzo, R. Analysis and design of RC structures strengthened with mechanically fastened FRP laminates: A review. Compos. B Eng. 2013, 55, 386–399. [Google Scholar] [CrossRef]
  9. Lee, J.H.; Lopez, M.M.; Bakis, C.E. Slip effects in reinforced concrete beams with mechanically fastened FRP strip. Cem. Concr. Compos. 2009, 31, 496–504. [Google Scholar] [CrossRef]
  10. Nardone, F.; Lignola, G.P.; Prota, A.; Manfredi, G.; Nanni, A. Modeling of flexural behavior of RC beams strengthened with mechanically fastened FRP strips. Compos. Struct. 2011, 93, 1973–1985. [Google Scholar] [CrossRef]
  11. Napoli, A.; Matta, F.; Martinelli, E.; Nanni, A.; Realfonzo, R. Modelling and verification of response of RC slabs strengthened in flexure with mechanically fastened FRP laminates. Mag. Concr. Res. 2010, 62, 593–605. [Google Scholar] [CrossRef]
  12. Martinelli, E.; Napoli, A.; Nunziata, B.; Realfonzo, R. A 1D finite element model for the flexural behaviour of RC beams strengthened with MF-FRP strips. Compos. Struct. 2014, 107, 190–204. [Google Scholar] [CrossRef]
  13. Faella, C.; Martinelli, E.; Nigro, E. Formulation and validation of a theoretical model for intermediate debonding in FRP strengthened RC beams. Compos. B Eng. 2008, 39, 645–655. [Google Scholar] [CrossRef]
  14. Popovics, S. A numerical approach to the complete stress strain curve for concrete. Cem. Concr. Res. 1973, 3, 583–559. [Google Scholar] [CrossRef]
  15. Okamura, H.; Maekawa, K.; Sivasubramaniyam, S. Verification of Modeling for Reinforced Concrete Finite Element. In Finite Element Analysis of Reinforced Concrete Structures, Proceedings of the Seminar ASCE, Tokyo, Japan, 21–24 May 1985; pp. 528–543.
  16. Realfonzo, R.; Martinelli, E.; Napoli, A.; Nunziata, B. Experimental investigation of the mechanical connection between FRP laminates and concrete. Compos. B: Eng. 2013, 45, 341–355. [Google Scholar] [CrossRef]
  17. Elsayed, W.E.; Ebead, U.A.; Neale, K.W. Studies on mechanically fastened fiber-reinforced polymer strengthening systems. ACI Struct. J. 2009, 106, 49–59. [Google Scholar]
  18. Borowicz, D.T. Rapid Strengthening of Concrete Beams with Powder-Actuated Fastening Systems and Fiber Reinforced Polymer (FRP) Composite Materials. MSc Thesis, University of Wisconsin-Madison, Madison, WI, USA, 2002. [Google Scholar]
  19. Ebead, U. Hybrid externally bonded/mechanically fastened fiber-reinforced polymer for RC beam strengthening. ACI Struct. J. 2011, 108, 669–678. [Google Scholar]
  20. Ekenel, M.; Rizzo, A.; Myers, J.J.; Nanni, A. Flexural fatigue behavior of reiforced concrete beams strengthened with FRP fabric and precured laminate systems. J. Comp. Constr. 2006, 10, 433–442. [Google Scholar] [CrossRef]
  21. El-Maaddawy, T.; Nessabi, A.; El-Dieb, A. Flexural response of corroded reinforced concrete beams strengthened with powder-actuated fastened composites. J. Compos. Constr. 2013. [Google Scholar] [CrossRef]
  22. Galati, D.; Rizzo, A.; Micelli, F. Comparison of reinforced concrete beams strengthened with FRP pre-cured laminate systems and tested under flexural loading. In Proceedings of the FRPRCS-8, Patras, Greece, 16–18 July 2007.
  23. Lamanna, A.J. Flexural Strengthening of Reinforced Concrete Beams with Mechanically Fastened Fiber Reinforced Polymer Strips. Ph.D. Thesis, University of Wisconsin-Madison, Madison, WI, USA, 2002. [Google Scholar]
  24. Lamanna, A.J.; Bank, L.C.; Scott, D.W. Flexural strengthening of reinforced concrete beams using fasteners and fiber-reinforced polymer strips. ACI Struct. J. 2001, 98, 368–376. [Google Scholar]
  25. Bank, L.C.; Lamanna, A.J.; Ray, J.C.; Velazquez, G.I. Rapid Strengthening of Reinforced Concrete Beams with Mechanically Fastened, Fiber Reinforced Polymeric Composites Materials; Report ERDC/GSL TR-02-4; US Army Corps of Engineers: Madison, WI, USA, 2002; pp. 1–99. [Google Scholar]
  26. Lamanna, A.J.; Bank, L.C.; Scott, D.W. Flexural strengthening of reinforced concrete beams by mechanically attaching fiber-reinforced polymer strips. J. Compos. Constr. 2004, 8, 203–210. [Google Scholar] [CrossRef]
  27. Lee, H.L.; Lopez, M.M.; Bakis, C.E. Flexural behavior of reinforced concrete beams strengthened with mechanically fastened FRP strip. In Proceedings of the FRPRCS-8, Patras, Greece, 16–18 July 2007.
  28. Martin, J.A.; Lamanna, A.J. Performance of mechanically fastened FRP strengthened concrete beams in flexure. J. Compos. Constr. 2008, 12, 257–265. [Google Scholar] [CrossRef]

Share and Cite

MDPI and ACS Style

Martinelli, E.; Napoli, A.; Nunziata, B.; Realfonzo, R. RC Beams Strengthened with Mechanically Fastened Composites: Experimental Results and Numerical Modeling. Polymers 2014, 6, 613-633. https://0-doi-org.brum.beds.ac.uk/10.3390/polym6030613

AMA Style

Martinelli E, Napoli A, Nunziata B, Realfonzo R. RC Beams Strengthened with Mechanically Fastened Composites: Experimental Results and Numerical Modeling. Polymers. 2014; 6(3):613-633. https://0-doi-org.brum.beds.ac.uk/10.3390/polym6030613

Chicago/Turabian Style

Martinelli, Enzo, Annalisa Napoli, Bruno Nunziata, and Roberto Realfonzo. 2014. "RC Beams Strengthened with Mechanically Fastened Composites: Experimental Results and Numerical Modeling" Polymers 6, no. 3: 613-633. https://0-doi-org.brum.beds.ac.uk/10.3390/polym6030613

Article Metrics

Back to TopTop