Next Article in Journal
Products and Mechanistic Investigations on the Reactions of Hydrazines with Ozone in Gas-Phase
Previous Article in Journal
Probabilistic Hesitant Intuitionistic Linguistic Term Sets in Multi-Attribute Group Decision Making
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

A New Model for Determining Weight Coefficients of Criteria in MCDM Models: Full Consistency Method (FUCOM)

1
Department of Logistics, Military academy, University of Defence in Belgrade, Pavla Jurisica Sturma 33, 11000 Belgrade, Serbia
2
Faculty of Transport and Traffic Engineering Doboj, University of East Sarajevo, Vojvode Mišića 52, 74000 Doboj, Bosnia and Herzegovina
3
Faculty of Technical Sciences, University of Novi Sad, Trg Dositeja Obradovica 6, 21000 Novi Sad, Serbia
*
Author to whom correspondence should be addressed.
Submission received: 21 August 2018 / Revised: 6 September 2018 / Accepted: 6 September 2018 / Published: 10 September 2018

Abstract

:
In this paper, a new multi-criteria problem solving method—the Full Consistency Method (FUCOM)—is proposed. The model implies the definition of two groups of constraints that need to satisfy the optimal values of weight coefficients. The first group of constraints is the condition that the relations of the weight coefficients of criteria should be equal to the comparative priorities of the criteria. The second group of constraints is defined on the basis of the conditions of mathematical transitivity. After defining the constraints and solving the model, in addition to optimal weight values, a deviation from full consistency (DFC) is obtained. The degree of DFC is the deviation value of the obtained weight coefficients from the estimated comparative priorities of the criteria. In addition, DFC is also the reliability confirmation of the obtained weights of criteria. In order to illustrate the proposed model and evaluate its performance, FUCOM was tested on several numerical examples from the literature. The model validation was performed by comparing it with the other subjective models (the Best Worst Method (BWM) and Analytic Hierarchy Process (AHP)), based on the pairwise comparisons of the criteria and the validation of the results by using DFC. The results show that FUCOM provides better results than the BWM and AHP methods, when the relation between consistency and the required number of the comparisons of the criteria are taken into consideration. The main advantages of FUCOM in relation to the existing multi-criteria decision-making (MCDM) methods are as follows: (1) a significantly smaller number of pairwise comparisons (only n − 1), (2) a consistent pairwise comparison of criteria, and (3) the calculation of the reliable values of criteria weight coefficients, which contribute to rational judgment.

1. Introduction

Determining the weights of criteria is one of the key problems that arise in multi-criteria analysis models. The problem of choosing an appropriate method of determining criteria weights in problems of multi-criteria decision-making (MCDM) is a very important stage, which complicates the decision-making process. Taking into account the fact that the weights of criteria can significantly influence the outcome of the decision-making process, it is clear that particular attention must be paid to the objectivity factors of criteria weights.
Roberts and Goodwin [1] provide an overview of the studies in which the advantages and disadvantages of the individual methods of determining the weights of criteria are considered. The authors whose literature was consulted [1,2,3,4] agree that the values of criteria weights are significantly conditioned by the methods of their determination. Moreover, there is no agreement upon the best method of determining criteria weights, nor is there agreement upon the method of the direct determination of the “real” set of weights. In the literature, however, there is agreement that the weights calculated by applying certain methods are more accurate than the weights obtained by the methods of a direct weight assignment based on the expert’s understanding of the significance of criteria.
By studying the available literature, it can be noticed that there is no unique classification of the methods of determining criteria weights and that it is carried out on several grounds, in accordance with the author’s perceptions and needs for solving a specific practical problem. Thus, the literature by [5] provides the classification of the methods of determining criteria weights, which is objective and subjective in relation to whether weights are calculated indirectly, on the basis of the outcomes (consequences), or they are obtained directly from the decision-maker. The classification of the methods of determining criteria weights, which is more extensive to a slightly greater extent, can be found in the literature by [4], where the methods of determining criteria weights are divided into: statistical and algebraic, holistic and decomposed, direct and indirect, and compensatory and non-compensatory. In algebraic methods, the n weight is calculated based on an n − 1 set of judgments (conclusions) by using a simple system of equations. Statistical methods include a regression analysis that can also provide guidance on the choice of weights. Decomposed procedures are based on the comparison of the one-to-one pair of criteria at a time, whereas in holistic methods, the decision-maker considers both the criteria and the alternatives when expressing his/her preferences and makes the overall assessment of the alternatives. In direct methods, the decision-maker compares two criteria by using a ratio scale, whereas in indirect methods, criteria weights are calculated based on the decision-maker’s preferences.
Based on the concept of compensation and trade-offs among criteria, methods can be classified as compensatory and non-compensatory [6]. Compensatory methods are used for the aggregation of partial values in the methods of multi-attribute utility theory, whereas non-compensatory methods are used to aggregate partial values in outranking methods. The compensatory methods most commonly used are: (1) the trade-off method [7], which discovers the decision-maker’s dilemmas through a pairwise examination of criteria; (2) the swing method [8], which implies the construction of the two extreme hypothetical scenarios W and B, where the first (W) presents the worst values of all criteria, and the second scenario (B) corresponds to the best values; (3) the SMART method (the Simple Multi-Attribute Rating Technique) [9], which implies the procedure for determining criteria weights by comparing criteria with the best, and the worst, criterion from a defined set of criteria; (4) the SMARTER (SMART Exploiting Ranks) method, whose authors Edwards and Barron [9], presented a new version of the SMART method that uses the centroid method to determine criteria weights.
Contrary to compensatory methods, non-compensatory methods mainly reflect the global values of the relative importance of criteria. Non-compensatory methods do not pay particular attention to the impact of the range of a specific decision-making context, which is important in constructing partial relations of preferences. The most commonly used non-compensatory methods are the following ones: (1) the point allocation method [10], which is one of the simplest methods used to determine criteria weights, where, according to the priority of criteria, a decision-maker distributes a certain number of points to each criterion; (2) the direct rating method [11], in which the decision-maker first ranks all the criteria according to their significance, and on the basis of the criterion rank, the decision-maker assigns a weight to each criterion; (3) the methods of pairwise comparisons, where the decision-maker compares each criterion with others and determines the level of preferences for each pair of such criteria. The ordinal scale helps to determine the preference value of one criterion against the other. One of the most commonly applied methods based on pairwise comparisons is the Analytic Hierarchy Process (AHP) method [12]. The methods of pairwise comparisons, in addition to the AHP method, also include the DEMATEL method [13] and the Best Worst Method (BWM) [14]; (4) the resistance to change method [1], which has the elements of the swing method and the pairwise comparison methods. The resistance to change method starts from the assumption that each criterion has two opposite sides (poles) of performance (the desirable and the undesirable) and the priorities of criteria are defined on the basis of these settings.
In addition to this classification, the majority of authors suggest the classification of the models of determining the weights of criteria into subjective and objective models [15,16]. Subjective approaches reflect the decision-maker’s subjective opinion and intuition. By such an approach, the decision-maker directly influences the outcome of the decision-making process, since the weights of criteria are determined based on the information obtained from the decision-maker or from the experts involved in the decision-making process. Objective approaches are based on determining the weights of criteria on the basis of the information contained in a decision-making matrix applying certain mathematical models. Objective approaches neglect the decision-maker’s opinion.
In a subjective approach, the decision-maker or experts give their opinion on the significance of criteria for a certain decision-making process in accordance with their system of preferences. There are many ways to obtain the weights of criteria by applying a subjective approach, which can vary in the number of the participants in the weighting process, the applied methods and the forming of the final weights of criteria. Subjective approaches are mainly based on the pairwise comparisons of criteria or the ranking of criteria. The most well-known objective methods are the following: the entropy method [17], the CRITIC method (Criteria Importance Through Intercriteria Correlation) [18] and the FANMA method, named after its authors [19].
This paper presents a new subjective model for determining the weights of criteria: the Full Consistency Method (FUCOM). The FUCOM algorithm is based on the pairwise comparisons of criteria, where only the n − 1 comparison in the model is necessary. The model implies the implementation of a simple algorithm with the ability to validate the model by determining the deviation from full consistency (DFC) of the comparison. The consistency of the model is defined on the basis of the satisfaction of mathematical transitivity conditions. One of the characteristics of the developed new method is the lowering of decision-maker’s subjectivity, which leads to consistency or symmetry in the weight values of the criteria. Since FUCOM belongs to the group of subjective models, the most well-known subjective models are presented in the following section. Through the overview of the literature, the advantages and disadvantages of the existing models are highlighted and the gap filled by the new model in the literature is emphasized.
Taking into account all of the foregoing, there is a need for a method that requires (1) a small number of the pairwise comparisons of criteria, (2) a possibility of defining DFC of the comparison, and (3) the appreciation of transitivity in the pairwise comparison of criteria. Accordingly, FUCOM has been developed and the following goals of this paper have been set. The first goal of the paper is to present a new model for determining the weights of criteria that requires only the n 1 pairwise comparison of criteria by applying any scale (either integer or decimal). The second goal is to define a model that allows the calculation of the comparison consistency degree and the validation of the results, by fully respecting the conditions of mathematical transitivity. The third goal of the paper is to define a model that enables the calculation of the reliable values of the weight coefficients of criteria that contribute to a rational judgment. The fourth contribution of the paper is the comparison of the FUCOM method with other common subjective methods such as the BWM model and the AHP model. The advantages of FUCOM in relation to the existing subjective models in the literature are hereinafter explained in detail.
The rest of the paper is organized in the following manner: in the paper’s second chapter a review of applications of subjective MCDM methods are given, while in the paper’s third chapter, an algorithm and the application of the FUCOM example are presented. In the fourth chapter of the paper, a comparison of the FUCOM results with the results obtained by means of the application of the AHP model and the BWM is performed, and a discussion about the FUCOM results is given. The fifth chapter provides the concluding observations and the directions for future research.

2. Review of Applications of Subjective MCDM Methods in Different Studies

The best-known methods from the group of the subjective methods of determining the weighting values of criteria are the following: the AHP method [12], the DEMATEL (Decision-making Trial and Evaluation Laboratory) method [13], the SWARA (Step-Wise Weight Assessment Ratio Analysis) method [20], and the BWM [14]. Each of these methods has a wide application in the various areas of science and technology, as well as in solving real-life problems. The AHP method was used in [21] to make a strategic decision in a transport system; i.e., for the purpose of the reconfiguration of the railway infrastructure in the port of Trieste. In [22], this method was used to determine the significance of the criteria in evaluating different transitivity alternatives in transport in Catania. In [23], the AHP method was used to identify and evaluate defects in the passenger transport system, whereas in [24], it was used to select an alternative to the electronic payment system. Stević et al. [25] carried out a site selection of a logistics center in Bosnia and Herzegovina by applying the AHP method. In [26], the DEMATEL method analyzed the risk in mutual relations in logistics outsourcing, whereas a combination of the AHP and the DEMATEL methods in [27] was also used in the field of risk; i.e., the integration of logistical information. The integration of the DEMATEL method is not rare, so in [28], together with the ANP and the DEA, a decision was made on the choice of the 3PL logistics provider. In terms of applying the SWARA method for the purpose of determining the weighting values of criteria in the field of transport and logistics for the observed period since 2015, it has not been noticed. Only its fuzzy form [29] was used to select the 3PL in the sustainable network of reverse logistics and a rough form [30] for the purpose of determining the significance of criteria to the procurement of railroad wagons. When the application of the BWM is concerned, the situation is similar—in its rough form, and in combination with the Rough SAW method, it was applied in [31] in a logistics company.
It is impossible not to notice that, despite the fact that it is a relatively old method, the AHP method is still used in a large number of publications in its crisp form [32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60]. This confirms the conclusions by Zavadskas et al. [16] that, in the literature, the AHP method is the method most commonly used to determine the weights of criteria and/or rank alternatives. The validation of the results in the AHP model are based on the degree of consistency, whose value is limited to max 0.10. Since it is necessary to respect mathematical transitivity in the pairwise comparisons of criteria, the deviation from transitivity results in an increase in inconsistency. In the AHP method, it is required to make the n ( n 1 ) / 2 pairwise comparisons of criteria [45]. A large number of comparisons complicate the application of the model, especially in the cases of a larger number of criteria. According to some authors [15], it is almost impossible to perform completely consistent pairwise comparisons in the AHP method if there are more than nine criteria. This problem is usually overcome by dividing criteria into subcriteria, which further complicates the model.
The DEMATEL method was also used in a large number of studies [61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92], but its main disadvantage is a lack of consistency measure; i.e., the inability to validate the results obtained. Therefore, the DEMATEL method is mainly used to determine the interaction among criteria and the diagram of relations [93,94]. The DEMATEL method is often used in order to determine the weights of criteria in combination with the ANP (Analytic Network Process) method [95]. This partly eliminates a disadvantage. The AHP and ANP methods have many aggregation procedures to obtain a preference vector from pairwise comparisons matrix. The SWARA method is applied because of its simplicity and a small number of steps. However, the SWARA method, like DEMATEL, does not have the ability to determine the consistency degree of the comparisons obtained. For this reason, the SWARA method is much less used in the literature than the two previously mentioned methods (the AHP and DEMATEL), which is evident from [96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113]. The BWM is the method that has increasingly been applied over a short time [114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,133,134,135,136,137]. Some authors [122,123,124,128,134,138,139,140] see this method as an adequate substitute for the AHP. Its major advantage is a smaller number of pairwise comparisons ( 2 n 3 ) compared to the AHP. However, the degree of consistency in this method ranges to one, which in certain cases reflects a high degree of subjectivity. Razei [14] proposes the determining of the interval values of weight coefficients as a solution to this problem and he suggests the determining of the mean values of intervals and taking that value as the final value of the weight of criteria. Nevertheless, due to the inconsistency of the results, there is no guarantee that the optimal values of weight coefficients will be within the defined intervals.

3. Full Consistency Method (FUCOM)

The problems of multi-criteria decision-making are characterized by the choice of the most acceptable alternative out of a set of the alternatives presented on the basis of the defined criteria. A model of multi-criteria decision-making can be presented by a mathematical equation max [ f 1 ( x ) , f 2 ( x ) , , f n ( x ) ] ,   n 2 , with the condition that x A = [ a 1 , a 2 , , a m ] ; where n represents the number of the criteria, m is the number of the alternatives, fj represents the criteria ( j = 1 , 2 , , n ) and A represents the set of the alternatives ai ( i = 1 , 2 , , m ). The values f i j of each considered criterion f j for each considered alternative a i are known, namely f i j = f j ( a i ) ,   ( i , j ) ;   i = 1 , 2 , , m ;   j = 1 , 2 , , n . The relation shows that each value of the attribute depends on the jth criterion and the ith alternative.
Real problems do not usually have the criteria of the same degree of significance. It is therefore necessary that the significance factors of particular criteria should be defined by using appropriate weight coefficients for the criteria, so that their sum is one. Determining the relative weights of criteria in multi-criteria decision-making models is always a specific problem inevitably accompanied by subjectivity. This process is very important and has a significant impact on the final decision-making result, since weight coefficients in some methods crucially influence the solution. Therefore, particular attention in this paper is paid to the problem of determining the weights of criteria, and the new FUCOM model for determining the weight coefficients of criteria is proposed. This method enables the precise determination of the values of the weight coefficients of all of the elements mutually compared at a certain level of the hierarchy, simultaneously satisfying the conditions of the comparison consistency, too.
In real life, pairwise comparison values a i j = w i / w j (where aij shows the relative preference of criterion i to criterion j) are not based on accurate measurements, but rather on subjective estimates. There is also a deviation of the values a i j from the ideal ratios w i / w j (where w i and w j represents criteria weights of criterion i and criterion j). If, for example, it is determined that A is of much greater significance than B, B of greater importance than C, and C of greater importance than A, there is inconsistency in problem solving and the reliability of the results decreases. This is especially true when there are a large number of the pairwise comparisons of criteria. FUCOM reduces the possibility of errors in a comparison to the least possible extent due to: (1) a small number of comparisons ( n 1 ) and (2) the constraints defined when calculating the optimal values of criteria. FUCOM provides the ability to validate the model by calculating the error value for the obtained weight vectors by determining DFC. On the other hand, in the other models for determining the weights of criteria (the BWM, the AHP models), the redundancy of the pairwise comparison appears, which makes them less vulnerable to errors in judgment, while the FUCOM methodological procedure eliminates this problem.
In the following section, the procedure for obtaining the weight coefficients of criteria by using FUCOM is presented.
Step 1. In the first step, the criteria from the predefined set of the evaluation criteria C = { C 1 , C 2 , , C n } are ranked. The ranking is performed according to the significance of the criteria; i.e., starting from the criterion that is expected to have the highest weight coefficient to the criterion of the least significance. Thus, the criteria ranked according to the expected values of the weight coefficients are obtained:
C j ( 1 ) > C j ( 2 ) > > C j ( k )
where k represents the rank of the observed criterion. If there is a judgment of the existence of two or more criteria with the same significance, the sign of equality is placed instead of “>” between these criteria in the expression (1).
Step 2. In the second step, a comparison of the ranked criteria is carried out and the comparative priority ( φ k / ( k + 1 ) , k = 1 , 2 , , n , where k represents the rank of the criteria) of the evaluation criteria is determined. The comparative priority of the evaluation criteria ( φ k / ( k + 1 ) ) is an advantage of the criterion of the C j ( k ) rank compared to the criterion of the C j ( k + 1 ) rank. Thus, the vectors of the comparative priorities of the evaluation criteria are obtained, as in the expression (2):
Φ = ( φ 1 / 2 , φ 2 / 3 , , φ k / ( k + 1 ) )
where φ k / ( k + 1 ) represents the significance (priority) that the criterion of the C j ( k ) rank has compared to the criterion of the C j ( k + 1 ) rank.
The comparative priority of the criteria is defined in one of the two ways defined in the following parts:
(a) Pursuant to their preferences, decision-makers define the comparative priority φ k / ( k + 1 ) among the observed criteria. Thus, for example, if two stones A and B, which, respectively, have the weights of w A = 300 grams and w B = 255 grams are observed, the comparative priority ( φ A / B ) of Stone A in relation to Stone B is φ A / B = 300 / 255 = 1.18 . Also, if the weights A and B cannot be determined precisely, but a predefined scale is used (e.g., from 1 to 9), then it can be said that stones A and B have weights w A = 8 and w B = 7 , respectively. Then the comparative priority ( φ A / B ) of Stone A in relation to Stone B can be determined as φ A / B = 8 / 7 = 1.14 . This means that stone A in relation to stone B has a greater priority (weight) by 1.18 (in the case of precise measurements); i.e., by 1.14 (in the case of application of measuring scale). In the same manner, decision-makers define the comparative priority among the observed criteria φ k / ( k + 1 ) . When solving real problems, decision-makers compare the ranked criteria based on internal knowledge, so they determine the comparative priority φ k / ( k + 1 ) based on subjective preferences. If the decision-maker thinks that the criterion of the C j ( k ) rank has the same significance as the criterion of the C j ( k + 1 ) rank, then the comparative priority is φ k / ( k + 1 ) = 1 .
(b) Based on a predefined scale for the comparison of criteria, decision-makers compare the criteria and thus determine the significance of each individual criterion in the expression (1). The comparison is made with respect to the first-ranked (the most significant) criterion. Thus, the significance of the criteria ( ϖ C j ( k ) ) for all of the criteria ranked in Step 1 is obtained. Since the first-ranked criterion is compared with itself (its significance is ϖ C j ( 1 ) = 1 ), a conclusion can be drawn that the n 1 comparison of the criteria should be performed.
For example: a problem with three criteria ranked as C2 > C1 > C3 is being subjected to consideration. Suppose that the scale ϖ C j ( k ) [ 1 , 9 ] is used to determine the priorities of the criteria and that, based on the decision-maker’s preferences, the following priorities of the criteria ϖ C 2 = 1 , ϖ C 1 = 3.5 and ϖ C 3 = 6 are obtained. On the basis of the obtained priorities of the criteria and condition w k w k + 1 = φ k / ( k + 1 ) we obtain following calculations w 2 w 1 = 3.5 1 i.e., w 2 = 3.5 w 1 , w 1 w 3 = 6 3.5 i.e., w 1 = 1.714 w 3 . In that way, the following comparative priorities are calculated: φ C 2 / C 1 = 3.5 / 1 = 3.5 and φ C 1 / C 3 = 6 / 3.5 = 1.714 (expression (2)).
As we can see from the example shown in Step 2b, the FUCOM model allows the pairwise comparison of the criteria by means of using integer, decimal values or the values from the predefined scale for the pairwise comparison of the criteria.
Step 3. In the third step, the final values of the weight coefficients of the evaluation criteria ( w 1 , w 2 , , w n ) T are calculated. The final values of the weight coefficients should satisfy the two conditions:
(1) that the ratio of the weight coefficients is equal to the comparative priority among the observed criteria ( φ k / ( k + 1 ) ) defined in Step 2; i.e., that the following condition is met:
w k w k + 1 = φ k / ( k + 1 )
(2) In addition to the condition (3), the final values of the weight coefficients should satisfy the condition of mathematical transitivity; i.e., that φ k / ( k + 1 ) φ ( k + 1 ) / ( k + 2 ) = φ k / ( k + 2 ) . Since φ k / ( k + 1 ) = w k w k + 1 and φ ( k + 1 ) / ( k + 2 ) = w k + 1 w k + 2 , that w k w k + 1 w k + 1 w k + 2 = w k w k + 2 is obtained. Thus, yet another condition that the final values of the weight coefficients of the evaluation criteria need to meet is obtained, namely:
w k w k + 2 = φ k / ( k + 1 ) φ ( k + 1 ) / ( k + 2 )
Full consistency i.e., minimum DFC ( χ ) is satisfied only if transitivity is fully respected; i.e., when the conditions of w k w k + 1 = φ k / ( k + 1 ) and w k w k + 2 = φ k / ( k + 1 ) φ ( k + 1 ) / ( k + 2 ) are met. In that way, the requirement for maximum consistency is fulfilled; i.e., DFC is χ = 0 for the obtained values of the weight coefficients. In order for the conditions to be met, it is necessary that the values of the weight coefficients ( w 1 , w 2 , , w n ) T meet the condition of | w k w k + 1 φ k / ( k + 1 ) | χ and | w k w k + 2 φ k / ( k + 1 ) φ ( k + 1 ) / ( k + 2 ) | χ , with the minimization of the value χ . In that manner the requirement for maximum consistency is satisfied.
Based on the defined settings, the final model for determining the final values of the weight coefficients of the evaluation criteria can be defined.
min χ s . t . | w j ( k ) w j ( k + 1 ) φ k / ( k + 1 ) | χ ,   j | w j ( k ) w j ( k + 2 ) φ k / ( k + 1 ) φ ( k + 1 ) / ( k + 2 ) | χ ,   j j = 1 n w j = 1 ,   j w j 0 ,   j
By solving the model (5), the final values of the evaluation criteria ( w 1 , w 2 , , w n ) T and the degree of DFC ( χ ) are generated. In order to achieve a better understanding of the presented model, two simple examples will demonstrate the process of determining weight coefficients by applying FUCOM. In the first example, the procedure for determining the comparative priority ( φ k / ( k + 1 ) ) is shown by applying Step 2a, whereas in the second example, φ k / ( k + 1 ) is determined by applying Step 2b.
Example 1.
The determination of the criteria weight coefficients will be presented through the example of the evaluation of transport-manipulative means in the logistics centers. There are four criteria identified for the evaluation of forklifts: the purchase price (C1), the manufacturer’s warranty (C2), the service network (C3), and the maximum load capacity (C4). As previously described, FUCOM was implemented through the following steps:
Step 1. In the first step, the decision-makers performed the ranking of the criteria: C1 > C2 > C3 > C4.
Step 2. In the second step (Step 2a), based on the decision-maker’s preferences, the comparative priorities of the ranked criteria were determined and the vector of the comparative priorities of the evaluation criteria was obtained (Table 1).
Step 3. The final values of the weight coefficients should meet the following two conditions:
(1) The final values of the weight coefficients should meet the condition (3); i.e., they should satisfy the relations defined by the vector of the comparative priorities of the evaluation criteria (Table 2). Thus, that w 1 w 2 = 1.08 , w 2 w 3 = 1.25 and w 3 w 4 = 1.45 is obtained.
(2) In addition to the condition (3), the final values of the weight coefficients should meet the condition of mathematical transitivity; i.e., the condition (4). Thus, that w 1 w 3 = 1.08 1.25 = 1.35 and w 2 w 4 = 1.25 1.45 = 1.81 is obtained.
Regarding the defined limitations, on the basis of the expression (5), a finite model for determining the weight coefficients meeting the condition of maximum consistency can be defined.
min χ s . t . { | w 1 w 2 1.08 | χ ,   | w 2 w 3 1.25 | χ ,   | w 3 w 4 1.45 | χ , | w 1 w 3 1.35 | χ ,   | w 2 w 4 1.81 | χ , j = 1 4 w j = 1 ,   w j 0 ,   j
By solving this model, the final values of the weight coefficients ( 0.315 , 0.291 , 0.233 , 0.161 ) T and DFC of the results χ = 0.00 are obtained. If the obtained values of the weight coefficients are compared by applying the expression (3), the values of the vector Φ given in Table 1 are obtained.
Example 2.
An example in which a car buyer evaluated the considered alternatives by using the following five criteria: Quality (C1), Price (C2), Comfort (C3), Safety Level (C4), and Interior (C5) were considered.
Step 1. In the first step, the decision-makers performed the ranking of the criteria: C2 > C1 > C4 > C3 > C5.
Step 2. In the second step (Step 2b), the decision-maker performed the pairwise comparison of the ranked criteria from Step 1. The comparison was made with respect to the first-ranked C2 criterion. The comparison was based on the scale [ 1 , 9 ] . Thus, the priorities of the criteria ( ϖ C j ( k ) ) for all of the criteria ranked in Step 1 were obtained (Table 2).
Based on the obtained priorities of the criteria, the comparative priorities of the criteria are calculated: φ C 2 / C 1 = 2.1 / 1 = 2.1 , φ C 1 / C 4 = 3 / 2.1 = 1.43 , φ C 4 / C 3 = 3 / 3 = 1 and φ C 3 / C 5 = 7 / 3 = 2.33 .
Step 3. The final values of weight coefficients should meet the following two conditions:
(1) The final values of the weight coefficients should meet the condition (3); i.e., that w 2 w 1 = 2.1 , w 1 w 4 = 1.43 , w 4 w 3 = 1 and w 3 w 5 = 2.33 .
(2) In addition to the condition (3), the final values of the weight coefficients should meet the condition of mathematical transitivity; i.e., that w 2 w 4 = 2.1 1.43 = 3.00 , w 1 w 3 = 1.43 1 = 1.43 and w 4 w 5 = 1 2.33 = 2.33 . By applying the expression (5), the final model for determining the weight coefficients can be defined as:
min χ s . t . { | w 2 w 1 2.1 | χ ,   | w 1 w 4 1.43 | χ ,   | w 4 w 3 1 | χ ,   | w 3 w 5 2.33 | χ , | w 2 w 4 3.00 | χ ,   | w 1 w 3 1.43 | χ ,   | w 4 w 5 2.33 | χ , j = 1 5 w j = 1 ,   w j 0 ,   j
By solving this model, the final values of the weight coefficients ( 0.437 , 0.208 , 0.146 , 0.146 , 0.063 ) T and DFC of the results χ = 0.00 are obtained.
The aim of applying all the multi-criteria models is to select the best (most desirable, most significant) alternative, in other words alternative with the best final value of the criterion function. The total value of the criterion function fi (i = 1, 2, …, m) of the alternative i, can be obtained using different methods. However, FUCOM can be successfully transformed into a classic multi-criteria model by adding the expression (6) that is presented in the next section. The values of the weight coefficients of the criteria obtained by FUCOM and which meet the condition that w j 0 and j = 1 n w j = 1 can also be used to determine the finite values of the criterion functions applying the expression (6)
f i = j = 1 n w j x i j
where w j represents optimal values of weight coefficients obtained using FUCOM, while x i j represents the values of alternatives according to optimization criteria in the initial decision matrix X = [ x i j ] m × n .
By the application of a simple additive weighted value function (6), which is the basic model for most MCDM methods, the FUCOM algorithm is transformed into a classical multi-criteria model that can be used to evaluate m alternative solutions by n optimization criteria.
With multi-criteria decision making, the authors recommend the complete FUCOM method to be applied to each decision-maker in particular. After obtaining the weight values of the criteria for all decision makers it is necessary to perform their simplification by applying some aggregators.

4. Discussion and Comparisons

In this chapter, based on the presented methodology, the advantages of FUCOM that make it a reliable and interesting MCDM model are distinguished. The benefits of FUCOM are shown by comparing it with the well-known methodologies for determining the weight coefficients of criteria. For the purpose of the comparison, the BWM and the AHP methods were put in focus, since the validity of both methodologies is based on meeting the conditions of mathematical transitivity and the pairwise comparison of the criteria. Depending on the satisfaction degree of transitivity requirements in the BWM and the AHP models, the consistency of the obtained results; i.e., the optimality of the solution is estimated. Taking into account the fact that FUCOM is methodologically based on assessing the comparative priority of criteria and on meeting the conditions of transitivity, the comparison by applying the BWM and the AHP models represents a logical step for comparing results and validating the model. Each of the selected advantages was analyzed through the examples discussed in the literature in which the BWM and the AHP approaches were applied.
(1) In comparison with similar subjective models (the AHP and the BWM methods) for determining the weight the coefficients of criteria, FUCOM only requires the n − 1 pairwise comparison of criteria. When the application of the AHP method is concerned, it is necessary to perform the n(n − 1)/2 pairwise comparison of criteria, whereas the application of the BWM method requires 2n − 3 comparisons. An increase in the number of criteria in the BWM and the AHP models produces a significant increase in the number of pairwise comparisons (Table 3), which greatly complicates the mathematical formulation of the models mentioned.
The research study [19] has shown that decision-makers can successfully perform pairwise comparisons up to a maximum of seven criteria, and exceptionally up to nine criteria. However, an increase in the number of criteria affects an increase in the required number of pairwise comparisons, which can significantly affect the consistency of the results obtained. Based on the relations shown in Table 3, it is noted that FUCOM has a significant advantage in relation to the BWM and the AHP methods, whereas simultaneously it provides results identical to those obtained by the application of the considered methodologies.
Example 3.
In this example, the problem of a task-oriented resource allocation in cloud computing was considered, inclusive of the application of the AHP method [141]. The comparison was made in pairs of eight criteria, with a total of 28 pairwise comparisons performed (Table 4).
The model shown in Table 5 can be successfully solved applying BWM. Based on the data in Table 5 (the fifth or seventh row in the table), the Best-to-Others (BO) vector A B = ( 2 , 4 , 1 , 4 , 1 , 4 , 1 , 4 ) T is formed. Also, based on the data in Table 5 (fourth, sixth or eighth columns), the Other-to-Worst (OW) vector A W = ( 2 , 1 , 41 , 4 , 1 , 4 , 1 ) T is formed. By introducing the BO and OW vectors in the BWM model, the identical values of the weight coefficients of the criteria are obtained, as well as in the AHP method (Table 4) with the degree of consistency CR = 0.
By applying FUCOM, the same values of the weight coefficients with only seven pairwise comparisons of the criteria were obtained, whereas the AHP method for this example requires 28 pairwise comparisons. In order for the FUCOM mathematical model to form, the data displayed in Table 4 (i.e., the comparisons made for the criterion bearing the highest weight coefficient (Criteria C3, C5 and C7)) were used. In this example, there are three most influential criteria, so we choose the comparisons made for one of the three criteria. Based on the comparisons for the C7 criterion in Table 4 (the data from the seventh row of Table 4), the criteria are possible to rank in the following manner: C3 = C5 = C7 > C1 > C2 = C4 = C6 = C8 and the priorities of the criteria can be determined (Table 5).
Based on the obtained priorities of the criteria, the comparative priorities of the criteria are calculated: φ T 3 / T 5 = φ T 5 / T 7 = 1 / 1 = 1 , φ T 7 / T 1 = 2 / 1 = 2 , φ T 1 / T 2 = 4 / 2 = 2 and φ T 2 / T 4 = φ T 4 / T 6 = φ T 6 / T 8 = 4 / 4 = 1 , and, the model for determining the optimal values of the weight coefficients:
min χ s . t . { | w 3 w 5 1 | χ ,   | w 5 w 7 1 | χ ,   | w 7 w 1 2 | χ ,   | w 1 w 2 2 | χ ,   | w 2 w 4 1 | χ , | w 4 w 6 1 | χ ,   | w 6 w 8 1 | χ ,   | w 3 w 7 1 | χ ,   | w 5 w 1 2 | χ ,   | w 7 w 2 4 | χ , | w 1 w 4 2 | χ ,   | w 2 w 6 1 | χ ,   | w 4 w 8 1 | χ , j = 1 8 w j = 1 ,   w j 0 ,   j
By solving the model, the identical values of the weight coefficients as those obtained in the AHP model are obtained, with DFC χ = 0.00 and with only seven pairwise comparisons of criteria.
Table 6 shows the values of weight coefficients of the criteria obtained by AHP, BWM, and FUCOM models for Example 3.
By using all three models (AHP, BWM, FUCOM) on the same example from the literature, it has been shown that FUCOM gives the simplest solution with only seven comparisons, followed by BWM with thirteen comparisons and eventually AHP with 23 comparisons.
Example 4.
When buying a car, the buyer considers five criteria: the quality (C1), the price (C2), comfort (C3), safety (C4) and the style (C5). By using the BWM method, the Best–to-Others (BO) and the Others–to-Worst (OW) vectors are obtained [118], A B = ( 2 , 1 , 4 , 2 , 8 ) T and A W = ( 4 , 8 , 2 , 4 , 1 ) T . By solving the BWM, the optimal values of the weight coefficients are obtained:
w 1 = 0.2105 ,   w 2 = 0.4211 ,   w 3 = 0.1053 ,   w 4 = 0.2105 ,   w 5 = 0.0526 ,
and the degree of consistency CR = 0.00.
Based on the References data [118], a pairwise comparison matrix of the AHP model (Table 7) was formed and the values of weight coefficients of the criteria were obtained with the degree of consistency CR = 0.029.
Using the AHP method, similar values of the weight coefficients of the criteria are obtained, as with BWM, but with a significantly higher number of pairwise comparisons. Differences in the values of weight coefficients between AHP and BWM are due to the incomplete consistency of results in the AHP model (CRAHP = 0.029, CRBWM = 0.000).
To determine the weight coefficients by using FUCOM, only the comparisons obtained in the BO vector of the BWM are used. Based on the BO vectors, the criteria are possible to rank as follows: C2 > C1 = C4 > C3 > C5, with only n − 1 comparison, and the priorities of the criteria can be determined (Table 8).
Thus, the comparative priorities of the criteria are obtained, namely φ C 2 / C 1 = 2 / 1 = 2 , φ C 1 / C 4 = 2 / 2 = 1 , φ C 4 / C 3 = 4 / 2 = 2 , and the model is formed.
min χ s . t . { | w 2 w 1 2 | χ ,   | w 1 w 4 1 | χ ,   | w 4 w 3 2 | χ ,   | w 5 w 3 2 | χ , | w 2 w 4 2 | χ ,   | w 1 w 3 2 | χ ,   | w 4 w 3 4 | χ , j = 1 5 w j = 1 ,   w j 0 ,   j
By solving the model, the identical values of the weight coefficients and χ = 0.00 , as in the BWM, are obtained, with only four pairwise comparisons of the criteria. FUCOM was also tested on other examples from the literature in which the BWM and the AHP models were used [118,142], and the optimal values of the weight coefficients of the criteria were obtained with the n − 1 number of the pairwise comparisons.
Table 9 shows the values of weight coefficients of the criteria obtained by AHP, BWM, and FUCOM models for Example 4.
From Table 9 it is noted that the optimal values of the weight coefficients of the criteria are given by BWM and FUCOM, while the AHP model has smaller deviations from the optimal values. The solution obtained by the AHP model is also acceptable, since the values of the degree of consistency are within the allowed limits, or CR ≤ 0.1 [12]. The simplest solution with only four comparisons is given by FUCOM, followed by the BWM with seven comparisons and eventually AHP with 23 comparisons.
(2) FUCOM allows satisfying the complete consistency of the model, by respecting the conditions of transitivity. The BWM and the AHP models are based on adherence to mathematical transitivity; i.e., on meeting the conditions that a i j a j k = a i k (where aij shows the relative preference of criterion i to criterion j and ajk shows the relative preference of criterion j to criterion k). If the pairs are compared, the obtained relation reads a 13 = 3 and a 34 = 6 ; then, in order to meet the condition of transitivity, a 14 should have the value a 14 = 18 . However, since the scale a i j [ 1 , 9 ] is applied in both models, in the largest number of the cases of the pairwise comparison, a 14 obtains the maximum value from the scale; i.e., a 14 = 9 . From the above example, it is noted that BWM and AHP models in the case of pairwise comparison deliberately allow certain deviations and ignore total transitivity. However, the deviation from transitivity results in a decrease in the consistency of the model, which further affects the reliability of the results. On the other hand, FUCOM always strives for the maximum consistency of results, which is one of the key conditions in a rational judgment. Meeting the conditions of consistency affects the reliability of results; i.e., the optimality of weight coefficients.
For example, in a research study conducted by Sener et al. [143], the GIS-AHP model for the selection of a solid waste disposal site is applied. In the research, ten criteria were used, and when the weight coefficients were being determined by using the AHP model, the consistency CR = 0.03908 was obtained. The obtained values of the weight coefficients are close to the optimal values, but they are not optimal since the consistency is CR ≠ 0. If FUCOM is applied for the same problem, the optimal values of the weight coefficients are obtained, with DFC equal to zero. A similar situation is found in the other examples [14,118,130,144,145,146,147,148,149] in which the BWM and the AHP models are used, where the weights of the criteria are obtained with the degree of consistency CR ≠ 0. By applying FUCOM to the same problems, the optimal values of the weight coefficients with the full consistency of the results (DFC = 0) are obtained. Through the examples from the References [14,118,130,144,145,146,147,148,149] tested so far, FUCOM has showed a high consistency of the results, since the DFC values have been approximately equal to zero (DFC ≈ 0). The model for determining the weight coefficients of the criteria requires the reliable reproduction of expert opinions, without introducing any additional imprecision and deviations. Therefore, the authors suggest that the values of DFCs for which the weight coefficients are acceptable, or close to optimal values, should be in the interval DFC ∈ [0, 0.025].
(3) As already noted above, the BWM use the scale [ 1 , 9 ] for the pairwise comparison in most cases. Since BWM only use the integer values from the interval [ 1 , 9 ] , the smallest possible relation between the best and the next value in the ranking is two. This means that, in the case of full consistency (CR = 0), the best criterion in relation to the next one will have an advantage minimally twice as great. Since the minimum value is aij = 2, it means that the ratio w i w j = 2 . This ratio in the BWM is violated only when the degree of consistency is different from zero; i.e., when the condition of the optimality of weight coefficients is violated. In FUCOM, as shown in Example 1, this ratio solely depends on the decision-maker’s preference since the preference is not defined on the basis of a predefined scale, but on the basis of the subjective assessment instead.
(4) The weight coefficients obtained by applying FUCOM are more reliable and contribute to the rational judgment. Compared to the BWM, FUCOM provides the more reliable values of weight coefficients since comparisons are made with a higher degree of consistency. In the BWM, in the case of insufficient consistency ( ξ 0.145 ), multi-optimality occurs [118]. In the case of multi-optimality in the BWM, it is recommended that the interval values of weight coefficients should be determined [118]. After forming the interval values of weight coefficients, the mean value of the interval is determined, which is further taken as the optimal value of weight coefficients. However, it does not guarantee that the central part of the interval represents the optimal values of such weight coefficients. The optimal value may be closer to the left or the right limit of the interval. In the cases of a greater inconsistency of the results, it may happen that the optimal values of the weight coefficients of the criteria are not included in the defined interval values. This occurs when the left and the right interval limits are defined for the relations significantly deviating from transitivity conditions; i.e., in the cases of a greater model inconsistency. Since in FUCOM the values of the weight coefficients of criteria are obtained on the basis of a small number of pairwise comparisons (n − 1), the values of weight coefficients are obtained with the maximum satisfaction of model consistency and with a high degree of optimality. The above-mentioned problem will be accounted for in the following example.
Example 5.
The same problem [118] as in Example 4 is considered, with the BO and the OW values of the vector: A B = ( 2 , 1 , 4 , 3 , 8 ) T and A W = ( 4 , 8 , 2 , 3 , 1 ) T . By applying the BWM, the values of the weight coefficients are obtained, w 1 = 0.2285 ,   w 2 = 0.4489 ,   w 3 = 0.1102 ,   w 4 = 0.1573 , w 5 = 0.0551 and ξ = 0.145 . Since ξ = 0.145 , the values obtained are not completely consistent, which results in the occurrence of the multi-optimality of the solution. It is therefore necessary that the optimal interval values of the weight coefficient should be determined [118]. By solving the BWM, the following interval values of the weight coefficients are obtained:
w 1 = [ 0.2145 , 0.2289 ] ,   w 1 ( c e n t e r ) = 0.2217 ; w 2 = [ 0.4461 , 0.4571 ] ,   w 2 ( c e n t e r ) = 0.4516 ; w 3 = [ 0.1085 , 0.1176 ] ,   w 1 ( c e n t e r ) = 0.1131 ; w 4 = [ 0.1563 , 0.1602 ] ,   w 4 ( c e n t e r ) = 0.1582 ; w 5 = [ 0.0548 , 0.0561 ] ,   w 5 ( c e n t e r ) = 0.0554.
By applying FUCOM in the given example, the optimal values of the weight coefficients with a high consistency of the model are obtained as follows: w 1 = 0.2262 , w 2 = 0.4527 , w 3 = 0.1134 , w 4 = 0.1509 , w 5 = 0.0556 and χ = 0.001 . The consistency of the results obtained by the application of the FUCOM model is much higher than that of the results obtained by applying the BWM. We note that the values of the FUCOM weight coefficients are within the defined intervals obtained by using the BWM, except for the criterion C4. For the criterion C4, the optimal value of the weight coefficient w 4 = 0.1509 (obtained by FUCOM) is not covered by the interval of the criterion C4 ( w 4 = [ 0.1563 , 0.1602 ] ,   w 4 ( center ) = 0.1582 ) defined by the BWM. For the remaining criteria, the optimum values of the weight coefficients are within the defined intervals, but they deviate from the central parts of the interval, which are recommended in the BWM as the optimal values of weight coefficients.

5. Conclusions

The results of the research study are clearly indicative of the justification for the development of a new credible model for determining the weight coefficients of criteria. On the one hand, FUCOM is based on a partly simple mathematical apparatus, and as such is expected to be affirmatively promoted by other authors. On the other hand, the model allows obtaining the credible and reliable weight coefficients that contribute to the rational judgment and obtaining credible results when making decisions. Therefore, the application of this model is significant.
Firstly, FUCOM is a tool that helps executives to deal with their own subjectivity in prioritizing criteria through a simple algorithm and by applying an acceptable scale. Secondly, FUCOM allows obtaining optimal weight coefficients with a possibility of validating them by the consistency of the results. Thirdly, the application of the FUCOM model allows us to obtain the optimum values of weight coefficients by using a simple mathematical apparatus that allows our favoring certain criteria in evaluating phenomena in accordance with the decision-maker’s current requirements and minimizing the risk of decision-making. In addition, FUCOM provides us with the optimal values of weight coefficients and reduces the subjective impact and inconsistency of experts’ preferences to the final values of criterion weights. By comparing FUCOM with other models in the third section of the paper, the robustness and objectivity of the model are demonstrated. The enviable stability of the obtained results is presented. One of the most important advantages is obtaining the same results as in the BWM and the AHP models by only performing the n − 1 comparison of criteria. Moreover, it has been shown that the model is flexible and suitable for application to various measuring scales for the purpose of representing experts’ preferences.
In the paper is shown the comparison of the newly developed FUCOM method with respect to the subjective methods like BWM and AHP. Of all the examples in which the comparison was performed, it can be concluded that the FUCOM method gives better results than those mentioned above, in particular in terms of consistency. However, it is necessary to take into account the fact that there is a large difference in the number of criteria comparisons, especially when it comes to a relationship with the AHP method. Therefore, it can be expected that in certain cases there will be different results of the same problem that is solved by different methods. In the examples and comparisons with the AHP method presented in this paper, there was no such case, but such a possibility should not be excluded from consideration. As with other subjective models for determining the weight of the criteria (AHP, BWM, SWARA, DEMATEL etc.) and with the FUCOM model there is a subjective influence of the decision maker on the final values of the weight of the criteria. This particularly refers to the first and second steps of FUCOM in which decision-makers rank the criteria according to their personal preferences and make pairwise comparisons of ranked criteria. However, unlike analyzed subjective models, FUCOM has showed significantly less variations in the obtained values of the weight coefficients of the criterion than the optimum values. In a large number of tests the obtained values of the weight coefficients of the criteria were equal to the optimal values; i.e., the deviation was DFC ≈ 0. From this it can be concluded that the FUCOM algorithm leads to negligible additional deviations, resulting in more reliable results that are in many cases equal to optimal values.
Taking into account the advantages of FUCOM, the need for software development and implementation for real-world applications is imposed. This will make the model significantly closer to users and will enable the exploitation of all of the benefits stated in the paper. We also suggest that the proposed model should be used in some other real-world applications and comparison of the results obtained by applying other MCDM methods. One of the directions for future research should be towards improving the validation of the model results. Finally, we propose that this model should be expanded through the application of different uncertainty theories, such as neutrosophic and fuzzy sets, rough numbers, grey theory, etc. The extension of FUCOM by using the theories of uncertainty will enable the processing of experts’ preferences even when comparisons are made on the basis of the data that are partially or even very little-known. This would enable an easier expression of the decision-maker’s preferences, simultaneously respecting the subjectivity and lack of information on particular phenomena.

Author Contributions

Conceptualization, D.P. and Ž.S.; Methodology, D.P. and Ž.S.; Validation, D.P., Ž.S. and S.S.; Investigation, D.P.; Data Curation, D.P., Ž.S. and S.S.; Writing-Original Draft Preparation, D.P., Ž.S. and S.S.; Writing-Review & Editing, D.P., Ž.S. and S.S.; Visualization, D.P. and Ž.S.

Funding

This research received no external funding.

Conflicts of Interest

The authors declare no conflict of interest

References

  1. Roberts, R.; Goodwin, P. Weight approximations in multi-attribute decision models. J. Multicrit. Decis. Anal. 2002, 11, 291–303. [Google Scholar] [CrossRef]
  2. Solymosi, T.; Dompi, J. Method for determining the weights of criteria: The centralized weights. Eur. J. Oper. Res. 1985, 26, 35–41. [Google Scholar] [CrossRef]
  3. Cook, W.D. Distance-based and ad hoc consensus models in ordinal preference ranking. Eur. J. Oper. Res. 2006, 172, 369–385. [Google Scholar] [CrossRef]
  4. Weber, M.; Borcherding, K. Behavioral influences on weight judgments in multiattribute decision making. Eur. J. Oper. Res. 1993, 67, 1–12. [Google Scholar] [CrossRef]
  5. Tzeng, G.-H.; Chen, T.-Y.; Wang, J.C. A weight-assessing method with habitual domains. Eur. J. Oper. Res. 1998, 110, 342–367. [Google Scholar] [CrossRef]
  6. Milićević, M.; Župac, G. Subjective approach to the determination of criteria weights. Vojnotehnicki Glasni 2012, 60, 48–70. [Google Scholar] [CrossRef] [Green Version]
  7. Keeney, R.L.; Raiffa, H. Decisions with Multiple Objectives; Wiley: New York, NY, USA, 1976. [Google Scholar]
  8. Von Winterfeldt, D.; Edwards, W. Decision Analysis and Behavioral Research; Cambridge University Press: Cambridge, UK, 1986. [Google Scholar]
  9. Edwards, W.; Barron, H. SMARTS and SMARTER: Improved Simple Methods for Multiattribute Utility Measurement. Organ. Behav. Hum. Decis. Process. 1994, 60, 306–325. [Google Scholar] [CrossRef]
  10. Van Grundy, A.B. Techniques of Structured Problem Solving; Van Nostra and Reinhold Company: New York, NY, USA, 1988. [Google Scholar]
  11. Arbel, A. Approximate articulation of preference and priority derivation. Eur. J. Oper. Res. 1989, 43, 317–326. [Google Scholar] [CrossRef]
  12. Saaty, T.L. Analytic Hierarchy Process; McGraw-Hill: New York, NY, USA, 1980. [Google Scholar]
  13. Gabus, A.; Fontela, E. World Problems an Invitation to Further Thought within the Framework of DEMATEL; Battelle Geneva Research Centre: Geneva, Switzerland, 1972; pp. 1–8. [Google Scholar]
  14. Rezaei, J. Best-worst multi-criteria decision-making method. Omega 2015, 53, 49–57. [Google Scholar] [CrossRef]
  15. Zhu, G.N.; Hu, J.; Qi, J.; Gu, C.C.; Peng, J.H. An integrated AHP and VIKOR for design concept evaluation based on rough number. Adv. Eng. Inform. 2015, 29, 408–418. [Google Scholar] [CrossRef]
  16. Zavadskas, E.K.; Govindan, K.; Antucheviciene, J.; Turskis, Z. Hybrid multiple criteria decision-making methods: A review of applications for sustainability issues. Econ. Res.-Ekonomska Istraživanja 2016, 29, 857–887. [Google Scholar] [CrossRef]
  17. Shannon, C.E.; Weaver, W. The Mathematical Theory of Communication; The University of Illinois Press: Urbana, IL, USA, 1947. [Google Scholar]
  18. Diakoulaki, D.; Mavrotas, G.; Papayannakis, L. Determining objective weights in multiple criteria problems: The CRITIC method. Comput. Oper. Res. 1995, 22, 763–770. [Google Scholar] [CrossRef]
  19. Srdjevic, B.; Medeiros, Y.; Srđević, Z.; Schaer, M. Evaluating management strategies in Paraguacu river basin by analytic hierarchy process. In Proceedings of the First Biennial Meeting of the International Environmental Modeling and Software Society, Lugano, Switzerland, 1 July 2002; Volume 1, pp. 42–47. [Google Scholar]
  20. Keršuliene, V.; Zavadskas, E.K.; Turskis, Z. Selection of rational dispute resolution method by applying new step-wise weight assessment ratio analysis (SWARA). J. Bus. Econ. Manag. 2010, 11, 243–258. [Google Scholar] [CrossRef]
  21. Giacomini, C.; Longo, G.; Lunardi, A.; Padoano, E. AHP-Aided Evaluation of Logistic and Transport Solutions in a Seaport. In Applications and Theory of Analytic Hierarchy Process-Decision Making for Strategic Decisions; InTech: Bruchsal, Germany, 2016; pp. 115–141. [Google Scholar]
  22. Ignaccolo, M.; Inturri, G.; García-Melón, M.; Giuffrida, N.; Le Pira, M.; Torrisi, V. Combining Analytic Hierarchy Process (AHP) with role-playing games for stakeholder engagement in complex transport decisions. Transp. Res. Procedia 2017, 27, 500–507. [Google Scholar] [CrossRef]
  23. Raymundo, H.; Reis, J.G.M. Passenger Transport Drawbacks: An Analysis of Its “Disutilities” Applying the AHP Approach in a Case Study in Tokyo, Japan. In IFIP International Conference on Advances in Production Management Systems; Springer: Cham, Switzerland, 2017; pp. 545–552. [Google Scholar]
  24. Olivková, I. Methodology for Assessment of Electronic Payment Systems in Transport Using AHP Method. In International Conference on Reliability and Statistics in Transportation and Communication; Springer: Cham, Switzerland, 2017; pp. 290–299. [Google Scholar]
  25. Stević, Ž.; Vesković, S.; Vasiljević, M.; Tepić, G. The selection of the logistics center location using AHP method. In Proceedings of the 2nd Logistics International Conference (LOGIC), Belgrade, Serbia, 21–23 May 2015; pp. 86–91. [Google Scholar]
  26. Govindan, K.; Chaudhuri, A. Interrelationships of risks faced by third party logistics service providers: A DEMATEL based approach. Transp. Res. Part E Logist. Transp. Rev. 2016, 90, 177–195. [Google Scholar] [CrossRef]
  27. Qu, Y.; Lu, Y.J. Risk factors analysis for logistics information integration based on the improved AHP-DEMATEL method. In Proceedings of the International Conference on Machine Learning and Cybernetics (ICMLC), Guangzhou, China, 12–15 July 2015; Volume 2, pp. 648–653. [Google Scholar]
  28. Adalı, E.; Işık, A. Integration of DEMATEL, ANP and DEA methods for third party logistics providers’ selection. Manag. Sci. Lett. 2016, 6, 325–340. [Google Scholar] [CrossRef]
  29. Zarbakhshnia, N.; Soleimani, H.; Ghaderi, H. Sustainable third-party reverse logistics provider evaluation and selection using fuzzy SWARA and developed fuzzy COPRAS in the presence of risk criteria. Appl. Soft Comput. 2018, 65, 307–319. [Google Scholar] [CrossRef]
  30. Zavadskas, E.K.; Stević, Ž.; Tanackov, I.; Prentkovskis, O. A Novel Multicriteria Approach-Rough Step-WiseWeight Assessment Ratio Analysis Method (R-SWARA) and Its Application in Logistics. Stud. Inf. Control 2018, 27, 97–106. [Google Scholar] [CrossRef]
  31. Stević, Ž.; Pamučar, D.; Kazimieras Zavadskas, E.; Ćirović, G.; Prentkovskis, O. The Selection of Wagons for the Internal Transport of a Logistics Company: A Novel Approach Based on Rough BWM and Rough SAW Methods. Symmetry 2017, 9, 264. [Google Scholar] [CrossRef]
  32. Jovanović, B.; Filipović, J.; Bakić, V. Prioritization of manufacturing sectors in Serbia for energy management improvement–AHP method. Energy Convers. Manag. 2015, 98, 225–235. [Google Scholar] [CrossRef]
  33. Stević, Ž.; Tanackov, I.; Vasiljević, M.; Vesković, S. Evaluation in logistics using combined AHP and EDAS method. In Proceedings of the XLIII International Symposium on Operational Research, Belgrade, Serbia, 8 March 2016; pp. 20–23. [Google Scholar]
  34. Yildiz, S.; Yildiz, E. Service quality evaluation of restaurants using the AHP and TOPSIS method. J. Soc. Adm. Sci. 2015, 2, 53–61. [Google Scholar]
  35. Büyüközkan, G.; Görener, A. Evaluation of product development partners using an integrated AHP-VIKOR model. Kybernetes 2015, 44, 220–237. [Google Scholar] [CrossRef]
  36. Rekik, M.; Boukadi, K.; Ben-Abdallah, H. A decision-making method for business process outsourcing to the cloud based on business motivation model and AHP. Int. J. Cloud Comput. 2015, 2, 47–62. [Google Scholar] [CrossRef]
  37. Plebankiewicz, E.; Kubek, D. Multicriteria selection of the building material supplier using AHP and fuzzy AHP. J. Constr. Eng. Manag. 2015, 142, 04015057. [Google Scholar] [CrossRef]
  38. Boujelbene, Y.; Derbel, A. The performance analysis of public transport operators in Tunisia using AHP method. Procedia Comput. Sci. 2015, 73, 498–508. [Google Scholar] [CrossRef]
  39. Osman, T.; Divigalpitiya, P.; Arima, T. Driving factors of urban sprawl in giza governorate of greater cairo metropolitan region using ahp method. Land Use Policy 2016, 58, 21–31. [Google Scholar] [CrossRef]
  40. Duan, Y.; Mu, H.; Li, N.; Li, L.; Xue, Z. Research on comprehensive evaluation of low carbon economy development level based on AHP-entropy method: A case study of Dalian. Energy Procedia 2016, 104, 468–474. [Google Scholar] [CrossRef]
  41. Socaciu, L.; Giurgiu, O.; Banyai, D.; Simion, M. PCM selection using AHP method to maintain thermal comfort of the vehicle occupants. Energy Procedia 2016, 85, 489–497. [Google Scholar] [CrossRef]
  42. Wang, D.; Zhao, J. Design optimization of mechanical properties of ceramic tool material during turning of ultra-high-strength steel 300M with AHP and CRITIC method. Int. J. Adv. Manuf. Technol. 2016, 84, 2381–2390. [Google Scholar] [CrossRef]
  43. Seo, J.; Bae, S. Identifying industry-specific components of product liability response system using Delphi-AHP method. Manag. Prod. Eng. Rev. 2016, 7, 27–38. [Google Scholar] [CrossRef]
  44. Kharat, M.G.; Raut, R.D.; Kamble, S.S.; Kamble, S.J. The application of Delphi and AHP method in environmentally conscious solid waste treatment and disposal technology selection. Manag. Environ. Qual. Int. J. 2016, 27, 427–440. [Google Scholar] [CrossRef]
  45. Božanić, D.; Tešić, D.; Milićević, J. A hybrid fuzzy AHP-MABAC model: Application in the Serbian Army—The selection of the location for deep wading as a technique of crossing the river by tanks. Decis. Mak. Appl. Manag. Eng. 2018, 1, 143–164. [Google Scholar] [CrossRef]
  46. Yagmur, L. Multi-criteria evaluation and priority analysis for localization equipment in a thermal power plant using the AHP (analytic hierarchy process). Energy 2016, 94, 476–482. [Google Scholar] [CrossRef]
  47. Krmac, E.; Djordjević, B. An Evaluation of Indicators of Railway Intelligent Transportation Systems using the Group Analytic Hierarchy Process. Electron. Sci. Technol. Appl. 2017, 4. [Google Scholar] [CrossRef]
  48. Nassereddine, M.; Eskandari, H. An integrated MCDM approach to evaluate public transportation systems in Tehran. Transp. Res. Part A Policy Pract. 2017, 106, 427–439. [Google Scholar] [CrossRef]
  49. Zeng, R.; Xu, C. Risk evaluation in auto spare parts transport based on the AHP method. MATEC Web Conf. 2017, 100, 05060. [Google Scholar] [CrossRef]
  50. Chabuk, A.; Al-Ansari, N.; Hussain, H.M.; Knutsson, S.; Pusch, R.; Laue, J. Combining GIS Applications and Method of Multi-Criteria Decision-Making (AHP) for Landfill Siting in Al-Hashimiyah Qadhaa, Babylon, Iraq. Sustainability 2017, 9, 1932. [Google Scholar] [CrossRef]
  51. Erdogan, S.A.; Šaparauskas, J.; Turskis, Z. Decision making in construction management: AHP and expert choice approach. Procedia Eng. 2017, 172, 270–276. [Google Scholar] [CrossRef]
  52. Aşchilean, I.; Badea, G.; Giurca, I.; Naghiu, G.S.; Iloaie, F.G. Choosing the optimal technology to rehabilitate the pipes in water distribution systems using the AHP method. Energy Procedia 2017, 112, 19–26. [Google Scholar] [CrossRef]
  53. Nizam, S.; Choen, E.L.; Phui, W.; Irfan, A. Developing weighting system for refurbishment building assessment scheme in Malaysia through analytic hierarchy process (AHP) approach. Energy Policy 2017, 112, 280–290. [Google Scholar] [CrossRef]
  54. Santarremigia, F.E.; Molero, G.D.; Poveda-Reyes, S.; Aguilar-Herrando, J. Railway safety by designing the layout of inland terminals with dangerous goods connected with the rail transport system. Saf. Sci. 2018. [Google Scholar] [CrossRef]
  55. Fortunet, C.; Durieux, S.; Chanal, H.; Duc, E. DFM method for aircraft structural parts using the AHP method. Int. J. Adv. Manuf. Technol. 2018, 95, 397–408. [Google Scholar] [CrossRef]
  56. Zhang, F.; Guo, S.; Ren, C.; Guo, P. Integrated IMO-TSP and AHP Method for Regional Water Allocation under Uncertainty. J. Water Resour. Plan. Manag. 2018, 144, 04018025. [Google Scholar] [CrossRef]
  57. Jabbarzadeh, A. Application of the AHP and TOPSIS in project management. J. Proj. Manag. 2018, 3, 125–130. [Google Scholar] [CrossRef]
  58. Sharawat, K.; Dubey, S.K. An Approach to Vendor Selection on Usability Basis by AHP and Fuzzy Topsis Method. In Soft Computing: Theories and Applications; Springer: Singapore, 2018; pp. 595–604. [Google Scholar] [CrossRef]
  59. Strojny, J.; Szulc, J.; Baran, M. Applying the AHP Method into the Assessment of Project Attitudes. In Eurasian Business Perspectives; Springer: Cham, Switzerland, 2018; pp. 183–197. [Google Scholar] [CrossRef]
  60. Khodaparast, M.; Rajabi, A.M.; Edalat, A. Municipal solid waste landfill siting by using GIS and analytical hierarchy process (AHP): A case study in Qom city, Iran. Environ. Earth Sci. 2018, 77, 52. [Google Scholar] [CrossRef]
  61. Kuo, S.Y.; Chen, S.C. Transportation Policy Making Using MCDM Model: The Case of Hualien. Transp. Plan. J. 2015, 44, 25–44. [Google Scholar]
  62. Wu, H.H.; Chang, S.Y. A case study of using DEMATEL method to identify critical factors in green supply chain management. Appl. Math. Comput. 2015, 256, 394–403. [Google Scholar] [CrossRef]
  63. Altuntas, S.; Dereli, T. A novel approach based on DEMATEL method and patent citation analysis for prioritizing a portfolio of investment projects. Expert Syst. Appl. 2015, 42, 1003–1012. [Google Scholar] [CrossRef]
  64. Sun, C.C. Identifying critical success factors in EDA industry using DEMATEL method. Int. J. Comput. Intell. Syst. 2015, 8, 208–218. [Google Scholar] [CrossRef]
  65. Guo, J.J.; Tsai, S.B. Discussing and evaluating green supply chain suppliers: A case study of the printed circuit board industry in China. S. Afr. J. Ind. Eng. 2015, 26, 56–67. [Google Scholar] [CrossRef]
  66. Uygun, Ö.; Kaçamak, H.; Kahraman, Ü.A. An integrated DEMATEL and Fuzzy ANP techniques for evaluation and selection of outsourcing provider for a telecommunication company. Comput. Ind. Eng. 2015, 86, 137–146. [Google Scholar] [CrossRef]
  67. Jeng, D.J.F.; Huang, K.H. Strategic project portfolio selection for national research institutes. J. Bus. Res. 2015, 68, 2305–2311. [Google Scholar] [CrossRef]
  68. Ranjan, R.; Chatterjee, P.; Chakraborty, S. Performance evaluation of Indian Railway zones using DEMATEL and VIKOR methods. Benchmark. Int. J. 2016, 23, 78–95. [Google Scholar] [CrossRef]
  69. Liang, H.; Ren, J.; Gao, Z.; Gao, S.; Luo, X.; Dong, L.; Scipioni, A. Identification of critical success factors for sustainable development of biofuel industry in China based on grey decision-making trial and evaluation laboratory (DEMATEL). J. Clean. Prod. 2016, 131, 500–508. [Google Scholar] [CrossRef]
  70. Seleem, S.N.; Attia, E.A.; El-Assal, A. Managing performance improvement initiatives using DEMATEL method with application case study. Prod. Plan. Control 2016, 27, 637–649. [Google Scholar] [CrossRef]
  71. Sharma, V.; Dixit, A.R.; Qadri, M.A. Empirical assessment of the causal relationships among lean criteria using DEMATEL method. Benchmark. Int. J. 2016, 23, 1834–1859. [Google Scholar] [CrossRef]
  72. Chauhan, A.; Singh, A.; Jharkharia, S. An ISM and DEMATEL method approach for the Analysis of Barriers of Waste Recycling in India. J. Air Waste Manag. Assoc. 2018, 68, 100–110. [Google Scholar] [CrossRef] [PubMed]
  73. Shahriari, M.R.; Pilevari, N.; Gholami, Z. The effect of information systems on the supply chain sustainability using DEMATEL method. Commun. Adv. Comput. Sci. Appl. 2016, 1, 47–56. [Google Scholar] [CrossRef]
  74. Malekzadeh, G.; Kazemi, M.; Lagzian, M.; Mortazavi, S. Modeling organizational intelligence using DEMATEL method in Iranian public universities. J. Model. Manag. 2016, 11, 134–153. [Google Scholar] [CrossRef]
  75. Yazdani, M.; Chatterjee, P.; Zavadskas, E.K.; Zolfani, S.H. Integrated QFD-MCDM framework for green supplier selection. J. Clean. Prod. 2017, 142, 3728–3740. [Google Scholar] [CrossRef]
  76. Zhan, Y.; Liu, J.; Ma, X. The Evaluation on the Suppliers of Prefabricated Housing Components Based on DEMATEL Method. In Proceedings of the 20th International Symposium on Advancement of Construction Management and Real Estate, Hangzhou, China, 23 October 2017; Springer: Singapore, 2017; pp. 653–662. [Google Scholar]
  77. Hsu, C.W.; Yeh, C.C. Understanding the factors affecting the adoption of the Internet of Things. Technol. Anal. Strat. Manag. 2017, 29, 1089–1102. [Google Scholar] [CrossRef]
  78. Sekhar, C.; Patwardhan, M.; Vyas, V. Study of intellectual capital dimensions in IT industry using DEMATEL method. J. Inf. Knowl. Manag. 2017, 16, 1750022. [Google Scholar] [CrossRef]
  79. Tang, H.W.V.; Chang, K.; Yin, M.S.; Sheu, R.S. Critical factors for implementing a programme for international MICE professionals: A hybrid MCDM model combining DEMATEL and ANP. Curr. Issues Tour. 2017, 20, 1527–1550. [Google Scholar] [CrossRef]
  80. Chou, Y.C.; Yang, C.H.; Lu, C.H.; Dang, V.T.; Yang, P.A. Building Criteria for Evaluating Green Project Management: An Integrated Approach of DEMATEL and ANP. Sustainability 2017, 9, 740. [Google Scholar] [CrossRef]
  81. Chatterjee, P.; Mondal, S.; Boral, S.; Banerjee, A.; Chakraborty, S. A novel hybrid method for non-traditional machining process selection using factor relationship and Multi-Attributive Border Approximation Method. Facta Univ. Ser. Mech. Eng. 2017, 15, 439–456. [Google Scholar] [CrossRef]
  82. Dehdasht, G.; Mohamad Zin, R.; Ferwati, M.S.; Mohammed Abdullahi, M.A.; Keyvanfar, A.; McCaffer, R. DEMATEL-ANP Risk Assessment in Oil and Gas Construction Projects. Sustainability 2017, 9, 1420. [Google Scholar] [CrossRef]
  83. Stefanović-Marinović, J.; Troha, S.; Milovančević, M. An Application of Multicriteria Optimization to the Two-Carrier Two-Speed Planetary Gear Trains. Facta Univ. Ser. Mech. Eng. 2017, 15, 85–95. [Google Scholar] [CrossRef]
  84. Chen, Y.H.; Wang, S.W.; Lee, C.; Lin, C.T. Using the DEMATEL Method to Explore the Critical Factors That Influence Visitors to Purchase Museum Cultural Products. J. Test. Eval. 2018, 46. [Google Scholar] [CrossRef]
  85. Pamučar, D.; Božanić, D.; Lukovac, V.; Komazec, N. Normalized weighted geometric bonferroni mean operator of interval rough numbers—Application in interval rough DEMATEL-COPRAS. Facta Univ. Ser. Mech. Eng. 2018, 16, 171–191. [Google Scholar] [CrossRef]
  86. Azimifard, A.; Moosavirad, S.H.; Ariafar, S. Designing steel supply chain and assessing the embedded CO2 emission based on the input-output table by using DEMATEL method. Manag. Decis. 2018, 56, 757–776. [Google Scholar] [CrossRef]
  87. Alzahrani, A.I.; Al-Samarraie, H.; Eldenfria, A.; Alalwan, N. A DEMATEL method in identifying design requirements for mobile environments: Students’ perspectives. J. Comput. High. Educ. 2018, 1–23. [Google Scholar] [CrossRef]
  88. Kumar, A.; Kaviani, M.A.; Bottani, E.; Dash, M.K.; Zavadskas, E.K. Investigating the role of social media in polio prevention in India: A Delphi-DEMATEL approach. Kybernetes 2018, 47, 1053–1072. [Google Scholar] [CrossRef]
  89. Chakraborty, S.; Chatterjee, P.; Prasad, K. An Integrated DEMATEL–VIKOR Method-Based Approach for Cotton Fibre Selection and Evaluation. J. Inst. Eng. (India) Ser. E 2018, 99, 63–73. [Google Scholar] [CrossRef]
  90. Petrović, I.; Kankaraš, M. DEMATEL-AHP multi-criteria decision making model for the selection and evaluation of criteria for selecting an aircraft for the protection of air traffic. Decis. Mak. Appl. Manag. Eng. 2018, 1. [Google Scholar] [CrossRef]
  91. Sharma, Y.K.; Mangla, S.K.; Patil, P.P.; Uniyal, S. Sustainable Food Supply Chain Management Implementation Using DEMATEL Approach. In Advances in Health and Environment Safety; Springer: Singapore, 2018; pp. 115–125. [Google Scholar] [CrossRef]
  92. Hashemkhani Zolfani, S.; Salimi, J.; Maknoon, R.; Kildiene, S. Technology foresight about R&D projects selection; Application of SWARA method at the policy making level. Eng. Econ. 2016, 26, 571–580. [Google Scholar] [CrossRef]
  93. Liu, F.; Aiwu, G.; Lukovac, V.; Vukic, M. A multicriteria model for the selection of the transport service provider: A single valued neutrosophic DEMATEL multicriteria model. Decis. Mak. Appl. Manag. Eng. 2018, 1. [Google Scholar] [CrossRef]
  94. Karavidic, Z.; Projovic, D. A multi-criteria decision-making (MCDM) model in the security forces operations based on rough sets. Decis. Mak. Appl. Manag. Eng. 2018, 1, 97–120. [Google Scholar] [CrossRef]
  95. Saaty, T.L.; Vargas, L.G. Models, Methods, Concepts and Applications of the Analytic Hierarchy Process; Springer Science and Business Media: Berlin, Germany, 2012; p. 175. [Google Scholar]
  96. Ghorshi Nezhad, M.R.; Hashemkhani Zolfani, S.; Moztarzadeh, F.; Zavadskas, E.K.; Bahrami, M. Planning the priority of high tech industries based on SWARA-WASPAS methodology: The case of the nanotechnology industry in Iran. Econ. Res.-Ekonomska Istraživanja 2015, 28, 1111–1137. [Google Scholar] [CrossRef] [Green Version]
  97. Kouchaksaraei, R.H.; Zolfani, S.H.; Golabchi, M. Glasshouse locating based on SWARA-COPRAS approach. Int. J. Strat. Prop. Manag. 2015, 19, 111–122. [Google Scholar] [CrossRef]
  98. Karabasevic, D.; Paunkovic, J.; Stanujkic, D. Ranking of companies according to the indicators of corporate social responsibility based on SWARA and ARAS methods. Serb. J. Manag. 2016, 11, 43–53. [Google Scholar] [CrossRef]
  99. Işık, A.T.; Adalı, E.A. A new integrated decision making approach based on SWARA and OCRA methods for the hotel selection problem. Int. J. Adv. Oper. Manag. 2016, 8, 140–151. [Google Scholar] [CrossRef]
  100. Nakhaei, J.; Lale Arefi, S.; Bitarafan, M.; Kildienė, S. Evaluation of light supply in the public underground safe spaces by using of COPRAS-SWARA methods. Int. J. Strat. Prop. Manag. 2016, 20, 198–206. [Google Scholar] [CrossRef]
  101. Shukla, S.; Mishra, P.K.; Jain, R.; Yadav, H.C. An integrated decision making approach for ERP system selection using SWARA and PROMETHEE method. Int. J. Intell. Enterp. 2016, 3, 120–147. [Google Scholar] [CrossRef]
  102. Vujić, D.; Stanujkić, D.; Urošević, S.; Karabašević, D. An approach to leader selection in the mining industry based on the use of weighted sum preferred levels of the performances method. Min. Metall. Eng. Bor 2016, 53–62. [Google Scholar] [CrossRef] [Green Version]
  103. Vesković, S.; Stević, Ž.; Stojić, G.; Vasiljević, M.; Milinković, S. Evaluation of the railway management model by using a new integrated model DELPHI-SWARA-MABAC. Decis. Mak. Appl. Manag. Eng. 2018, 1. [Google Scholar] [CrossRef]
  104. Hong, H.; Panahi, M.; Shirzadi, A.; Ma, T.; Liu, J.; Zhu, A.X.; Kazakis, N. Flood susceptibility assessment in Hengfeng area coupling adaptive neuro-fuzzy inference system with genetic algorithm and differential evolution. Sci. Total Environ. 2017, 621, 1124–1141. [Google Scholar] [CrossRef] [PubMed]
  105. Valipour, A.; Yahaya, N.; Md Noor, N.; Antuchevičienė, J.; Tamošaitienė, J. Hybrid SWARA-COPRAS method for risk assessment in deep foundation excavation project: An Iranian case study. J. Civ. Eng. Manag. 2017, 23, 524–532. [Google Scholar] [CrossRef]
  106. Juodagalvienė, B.; Turskis, Z.; Šaparauskas, J.; Endriukaitytė, A. Integrated multi-criteria evaluation of house’s plan shape based on the EDAS and SWARA methods. Eng. Struct. Technol. 2017, 9, 117–125. [Google Scholar] [CrossRef]
  107. Jain, N.; Singh, A.R. Fuzzy Kano Integrated MCDM Approach for Supplier Selection Based on Must Be Criteria. Int. J. Supply Chain Manag. 2017, 6, 49–59. [Google Scholar]
  108. Urosevic, S.; Karabasevic, D.; Stanujkic, D.; Maksimovic, M. An approach to personnel selection in the tourism industry based on the SWARA and the WASPAS methods. Econ. Comput. Econ. Cybern. Stud. Res. 2017, 51, 75–88. [Google Scholar]
  109. Panahi, S.; Khakzad, A.; Afzal, P. Application of stepwise weight assessment ratio analysis (SWARA) for copper prospectivity mapping in the Anarak region, central Iran. Arab. J. Geosci. 2017, 10, 484. [Google Scholar] [CrossRef]
  110. Ighravwe, D.E.; Oke, S.A. Sustenance of zero-loss on production lines using Kobetsu Kaizen of TPM with hybrid models. Total Qual. Manag. Bus. Excell. 2017, 1–25. [Google Scholar] [CrossRef]
  111. Heidary Dahooie, J.; Beheshti Jazan Abadi, E.; Vanaki, A.S.; Firoozfar, H.R. Competency-based IT personnel selection using a hybrid SWARA and ARAS-G methodology. Hum. Factors Ergon. Manuf. Serv. Ind. 2018, 28, 5–16. [Google Scholar] [CrossRef]
  112. Keshavarz Ghorabaee, M.; Amiri, M.; Zavadskas, E.K.; Antucheviciene, J. A new hybrid fuzzy MCDM approach for evaluation of construction equipment with sustainability considerations. Arch. Civ. Mech. Eng. 2018, 18, 32–49. [Google Scholar] [CrossRef]
  113. Fazli, M.; Afshari, A.J.; Hajiaghaei-Keshteli, M. Identification and ranking of risks in Green Building projects using the hybrid SWARA-COPRAS method. In Proceedings of the International conference of Iranian Operations Research Society, Kermanshah, Iran, 2–4 May 2018; pp. 1–5. [Google Scholar]
  114. Rezaei, J.; Wang, J.; Tavasszy, L. Linking supplier development to supplier segmentation using Best Worst Method. Expert Syst. Appl. 2015, 42, 9152–9164. [Google Scholar] [CrossRef]
  115. Sadaghiani, S.; Ahmad, K.W.; Rezaei, J.; Tavasszy, L. Evaluation of external forces affecting supply chain sustainability in oil and gas industry using Best Worst Method. In Proceedings of the 2015 International Mediterranean Gas and Oil Conference (MedGO), Mechref, Lebanon, 16–18 April 2015; pp. 1–4. [Google Scholar]
  116. Salimi, N.; Rezaei, J. Measuring efficiency of university-industry Ph. D. projects using best worst method. Scientometrics 2016, 109, 1911–1938. [Google Scholar] [CrossRef] [PubMed]
  117. Gupta, H.; Barua, M.K. Identifying enablers of technological innovation for Indian MSMEs using best–worst multi criteria decision making method. Technol. Forecast. Soc. Chang. 2016, 107, 69–79. [Google Scholar] [CrossRef]
  118. Rezaei, J. Best-worst multi-criteria decision-making method: Some properties and a linear model. Omega 2016, 64, 126–130. [Google Scholar] [CrossRef]
  119. Rezaei, J.; Nispeling, T.; Sarkis, J.; Tavasszy, L. A supplier selection life cycle approach integrating traditional and environmental criteria using the best worst method. J. Clean. Prod. 2016, 135, 577–588. [Google Scholar] [CrossRef]
  120. You, X.; Chen, T.; Yang, Q. Approach to multi-criteria group decision-making problems based on the best-worst-method and electre method. Symmetry 2016, 8, 95. [Google Scholar] [CrossRef]
  121. Van de Kaa, G.; Kamp, L.; Rezaei, J. Selection of biomass thermochemical conversion technology in the Netherlands: A best worst method approach. J. Clean. Prod. 2017, 166, 32–39. [Google Scholar] [CrossRef]
  122. Van de Kaa, G.; Scholten, D.; Rezaei, J.; Milchram, C. The Battle between Battery and Fuel Cell Powered Electric Vehicles: A BWM Approach. Energies 2017, 10, 1707. [Google Scholar] [CrossRef]
  123. Ghaffari, S.; Arab, A.; Nafari, J.; Manteghi, M. Investigation and evaluation of key success factors in technological innovation development based on BWM. Decis. Sci. Lett. 2017, 6, 295–306. [Google Scholar] [CrossRef]
  124. Gupta, H.; Barua, M.K. Supplier selection among SMEs on the basis of their green innovation ability using BWM and fuzzy TOPSIS. J. Clean. Prod. 2017, 152, 242–258. [Google Scholar] [CrossRef]
  125. Ahmadi, H.B.; Kusi-Sarpong, S.; Rezaei, J. Assessing the social sustainability of supply chains using Best Worst Method. Resour. Conserv. Recycl. 2017, 126, 99–106. [Google Scholar] [CrossRef]
  126. Salimi, N. Quality assessment of scientific outputs using the BWM. Scientometrics 2017, 112, 195–213. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  127. Petković, D.; Madić, M.; Radovanović, M.; Gečevska, V. Application Of The Performance Selection Index Method For Solving Machining MCDM Problems. Facta Univ. Ser. Mech. Eng. 2017, 15, 97–106. [Google Scholar] [CrossRef]
  128. You, P.; Guo, S.; Zhao, H.; Zhao, H. Operation Performance Evaluation of Power Grid Enterprise Using a Hybrid BWM-TOPSIS Method. Sustainability 2017, 9, 2329. [Google Scholar] [CrossRef]
  129. Rezaei, J.; Hemmes, A.; Tavasszy, L. Multi-criteria decision-making for complex bundling configurations in surface transportation of air freight. J. Air Transp. Manag. 2017, 61, 95–105. [Google Scholar] [CrossRef]
  130. Ren, J.; Liang, H.; Chan, F.T. Urban sewage sludge, sustainability, and transition for Eco-City: Multi-criteria sustainability assessment of technologies based on best-worst method. Technol. Forecast. Soc. Chang. 2017, 116, 29–39. [Google Scholar] [CrossRef]
  131. Praditya, D.; Janssen, M. Assessment of Factors Influencing Information Sharing Arrangements Using the Best-Worst Method. In Conference on e-Business, e-Services and e-Society; Springer: Cham, Switzerland, 2017; pp. 94–106. [Google Scholar]
  132. Salimi, N.; Rezaei, J. Evaluating firms’ R&D performance using best worst method. Eval. Program Plan. 2018, 66, 147–155. [Google Scholar] [CrossRef]
  133. Askarifar, K.; Motaffef, Z.; Aazaami, S. An investment development framework in Iran’s seashores using TOPSIS and best-worst multi-criteria decision making methods. Decis. Sci. Lett. 2018, 7, 55–64. [Google Scholar] [CrossRef]
  134. Rezaei, J.; Kothadiya, O.; Tavasszy, L.; Kroesen, M. Quality assessment of airline baggage handling systems using SERVQUAL and BWM. Tour. Manag. 2018, 66, 85–93. [Google Scholar] [CrossRef]
  135. Kara, M.E.; Fırat, S.Ü.O. Supplier Risk Assessment Based on Best-Worst Method and K-Means Clustering: A Case Study. Sustainability 2018, 10, 1066. [Google Scholar] [CrossRef]
  136. Abadi, F.; Sahebi, I.; Arab, A.; Alavi, A.; Karachi, H. Application of best-worst method in evaluation of medical tourism development strategy. Decis. Sci. Lett. 2018, 7, 77–86. [Google Scholar] [CrossRef]
  137. Yadollahi, S.; Kazemi, A.; Ranjbarian, B. Identifying and prioritizing the factors of service experience in banks: A Best-Worst method. Decis. Sci. Lett. 2018, 7, 455–464. [Google Scholar] [CrossRef]
  138. Badi, I.; Ballem, M. Supplier Selection using rough BWM-MAIRCA model: A case study in pharmaceutical supplying in Libya. Decis. Mak. Appl. Manag. Eng. 2018, 1, 15–32. [Google Scholar] [CrossRef]
  139. Pamučar, D.; Petrović, I.; Ćirović, G. Modification of the Best-Worst and MABAC methods: A novel approach based on interval-valued fuzzy-rough numbers. Expert Syst. Appl. 2018, 91, 89–106. [Google Scholar] [CrossRef]
  140. Pamučar, D.; Gigović, L.; Bajić, Z.; Janošević, M. Location selection for wind farms using GIS multi-criteria hybrid model: An approach based on fuzzy and rough numbers. Sustainability 2017, 9, 1315. [Google Scholar] [CrossRef]
  141. Ergu, D.; Kou, G.; Peng, Y.; Shi, Y.; Shi, Y. The analytic hierarchy process: Task scheduling and resource allocation in cloud computing environment. J. Supercomput. 2013, 64, 835–848. [Google Scholar] [CrossRef]
  142. Lam, K.C.; Lam, M.C.-K.; Wang, D. MBNQA-oriented self-assessment quality management system for contractors: Fuzzy AHP approach. Constr. Manag. Econ. 2008, 26, 447–461. [Google Scholar] [CrossRef]
  143. Sener, S.; Sener, E.; Karagüzel, R. Solid waste disposal site selection with GIS and AHP methodology: A case study in Senirkent–Uluborlu (Isparta) Basin, Turkey. Environ. Monit. Assess. 2011, 173, 533–554. [Google Scholar] [CrossRef] [PubMed]
  144. Anane, M.; Kallali, H.; Jellali, S.; Ouessar, M. Ranking suitable sites for Soil Aquifer Treatment in Jerba Island (Tunisia) using remote sensing, GIS and AHP-multicriteria decision analysis. Int. J. Water 2008, 4, 121–135. [Google Scholar] [CrossRef]
  145. Xia, J.; Zhao, Z.; Li, W.; Wang, Q. A Traffic Accident Causation Analysis Method Based on AHP-Apriori. Procedia Eng. 2016, 137, 680–687. [Google Scholar] [CrossRef]
  146. Ishizaka, A. Comparison of Fuzzy logic, AHP, FAHP and Hybrid Fuzzy AHP for new supplier selection and its performance analysis. Int. J. Integr. Supply Manag. 2014, 9, 1–22. [Google Scholar] [CrossRef] [Green Version]
  147. Shojaei, P.; Haeri, S.A.S.; Mohammadi, S. Airports evaluation and ranking model using Taguchi loss function, best-worst method and VIKOR technique. J. Air Transp. Manag. 2018, 68, 4–13. [Google Scholar] [CrossRef]
  148. Wan Ahmad, W.N.K.; Rezaei, J.; Sadaghiani, S.; Tavasszy, L.A. Evaluation of the external forces affecting the sustainability of oil and gas supply chain using Best Worst Method. J. Clean. Prod. 2017, 153, 242–252. [Google Scholar] [CrossRef]
  149. Sennaroglu, B.; Celebi, G.V. A military airport location selection by AHP integrated PROMETHEE and VIKOR methods. Transp. Res. Part D 2018, 59, 160–173. [Google Scholar] [CrossRef]
Table 1. The vector of the comparative priorities of the evaluation criteria ( Φ ).
Table 1. The vector of the comparative priorities of the evaluation criteria ( Φ ).
CriteriaC1C2C3C4
φ k / ( k + 1 ) 1.001.081.251.45
Table 2. Priorities of criteria.
Table 2. Priorities of criteria.
CriteriaC2C1C4C3C5
ϖ C j ( k ) 12.1337
Table 3. The required number of comparisons in Analytic Hierarchy Process (AHP), Best Worst Method (BWM) and the Full Consistency Method (FUCOM).
Table 3. The required number of comparisons in Analytic Hierarchy Process (AHP), Best Worst Method (BWM) and the Full Consistency Method (FUCOM).
MCDM MethodThe Number of Criteria (n) and the Required Number of Pairwise Comparisons
n = 2n = 3n = 4n = 5n = 6n = 7n = 8n = 9
AHP (n(n − 1)/2)1361015212836
BWM (2n − 3)13579111315
FUCOM (n − 1)12345678
Table 4. The pairwise comparison of eight criteria in the AHP model [141].
Table 4. The pairwise comparison of eight criteria in the AHP model [141].
CriteriaC1C2C3C4C5C6C7C8wj
C1121/221/221/220.1111
C21/21411/411/410.0556
C321/41414140.2222
C41/211/411/411/410.0556
C5241414140.2222
C61/211/411/411/410.0556
C7241414140.2222
C81/211/411/411/410.0556
CR = 0.000
Table 5. The priorities of the criteria.
Table 5. The priorities of the criteria.
CriteriaC3C5C7C1C2C4C6C8
ϖ C j ( k ) 11124444
Table 6. Results of AHP, BWM, and FUCOM models implementation (Example 3).
Table 6. Results of AHP, BWM, and FUCOM models implementation (Example 3).
CriteriaAHP (wj)BWM (wj)FUCOM (wj)
C10.11110.11110.1111
C20.05560.05560.0556
C30.22220.22220.2222
C40.05560.05560.0556
C50.22220.22220.2222
C60.05560.05560.0556
C70.22220.22220.2222
C80.05560.05560.0556
CR0.0000.0000.000
Table 7. Pairwise comparisons of criteria - AHP method.
Table 7. Pairwise comparisons of criteria - AHP method.
CriteriaC1C2C3C4C5wj
C11.0000.3333.0001.0005.0000.2017
C23.0001.0005.0003.0007.0000.4641
C30.3330.2001.0000.3333.0000.0888
C41.0000.3333.0001.0005.0000.2017
C50.2000.1430.3330.2001.0000.0436
Table 8. The priorities of the criteria.
Table 8. The priorities of the criteria.
CriteriaC2C1C4C3C5
ϖ C j ( k ) 12248
Table 9. Results of the AHP, BWM, and FUCOM models application (Example 4).
Table 9. Results of the AHP, BWM, and FUCOM models application (Example 4).
CriteriaAHP (wj)BWM (wj)FUCOM (wj)
C10.20170.21050.2105
C20.46410.42110.4211
C30.08880.10530.1053
C40.20170.21050.2105
C50.04360.05260.0526
CR0.0290.0000.000

Share and Cite

MDPI and ACS Style

Pamučar, D.; Stević, Ž.; Sremac, S. A New Model for Determining Weight Coefficients of Criteria in MCDM Models: Full Consistency Method (FUCOM). Symmetry 2018, 10, 393. https://0-doi-org.brum.beds.ac.uk/10.3390/sym10090393

AMA Style

Pamučar D, Stević Ž, Sremac S. A New Model for Determining Weight Coefficients of Criteria in MCDM Models: Full Consistency Method (FUCOM). Symmetry. 2018; 10(9):393. https://0-doi-org.brum.beds.ac.uk/10.3390/sym10090393

Chicago/Turabian Style

Pamučar, Dragan, Željko Stević, and Siniša Sremac. 2018. "A New Model for Determining Weight Coefficients of Criteria in MCDM Models: Full Consistency Method (FUCOM)" Symmetry 10, no. 9: 393. https://0-doi-org.brum.beds.ac.uk/10.3390/sym10090393

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop