Fibers, Volume 8, Issue 8 (August 2020) – 5 articles

One of the challenges of the century is to reach compatibility between the required resistance and the usage of lightweight building materials that may negatively affect the mechanical properties. Natural fibers nowadays are used as enhancers in the industrial field. Hence, the fibers contribute by giving an ideal solution to improve mechanical proprieties of the structural elements such as tensile and impact strength. In previous studies, the use of natural fibers as reinforcement in construction materials has increased. Natural fibers have a lot of characteristics such as being strong, lightweight, inexpensive, and eco-friendly. This paper aims to investigate the performance of banana fiber bars (BFB) as reinforced material. Through this study, the development and characterization of natural fibers-based composite beams were observed. After the beams were designed, several types of finite element analysis were conducted using ‘ANSYS’ nonlinear finite element program under one-point loading. Results show good correlations between experimental and predicted results. Full article

Activated carbons are widely used for sustainable technology of adsorptive transformation and storage of heat. Here, we analyze the applicability of twelve commercial carbons and an innovative carbonaceous composite “LiCl confined to multi-wall carbon nanotubes” (LiCl/MWCNT) for a new cycle “Heat from Cold” (HeCol). It has recently been proposed for amplification of low- temperature ambient heat in cold countries. The analysis is made in terms of the methanol mass exchanged and the useful heat generated per cycle; the latter is the main performance indicator of HeCol cycles. The maximum specific useful heat, reaching 990 and 1750 J/g, can be obtained by using carbon Maxsorb III and the composite, respectively. For these materials, methanol adsorption dynamics under typical HeCol conditions are experimentally studied by the large pressure jump method. Before making this analysis, the fine carbon powder is consolidated by either using a binder or just pressing to obtain larger particles (ca. 2 mm). The methanol desorption from the consolidated samples of Maxsorb III at T = 2 °C is faster than for LiCl/MWCNT, and the maximum (initial) useful power reaches (2.5–4.0) kW/kg sorbent. It is very promising for designing compact HeCol units utilizing the carbon Maxsorb III. Full article

This study reports on the use of poly(lactic acid) (PLA) as a renewable thermoplastic adhesive for laminated panels using birch, spruce, and pine veneers. Consolidated panels were prepared from veneer and PLA foils by hot-pressing from 140 to 180 °C to achieve minimum bondline temperatures. Evaluation of panel properties revealed that the PLA-bonded panels met minimum tensile strength and internal bond strength performance criteria. However, the adhesion interface which developed within individual bondlines varied with distinctions between hardwood and softwood species and PLA grades. Birch samples developed greater bondline strength with a higher pressing temperature using semi-crystalline PLA, whereas higher temperatures produced a poorer performance with the use of amorphous PLA. Panels formed with spruce or pine veneers had lower bondline performance and were also similarly distinguished by their pressing temperature and PLA grade. Furthermore, the potential for PLA-bonded laminated panels was demonstrated by cold water soak testing. Samples exhibiting relatively greater bondline adhesion had wet tensile strength values comparable to those tested in dry state. Our study outcomes suggest the potential for PLA bonding of veneers and panel overlays with the added benefits of being renewable and a no added formaldehyde system. Full article

A large part of the European building Heritage is dated back over centuries. Consequently, its structural and thermal performances are often inadequate. Commonly, different interventions are proposed for solving these issues separately. However, reasonable drawbacks arise when the structural retrofitting requires a direct contact with the target-member while the insulation layer is potentially interposed in between. In this scenario, the present research proposes a novel and unique system able to guarantee both the energetic and the structural retrofitting. Inorganic Matrix Composites (IMCs) are a promising solution in this sense. Among them, the Fabric Reinforced Cementitous Matrix (FRCM) is one of the most used; or rather a composite made of a fabric (open grid or mesh) within an inorganic matrix (lime or cement based). Even if the inorganic matrix has a relevant thickness (if compared with the one of the fabric), its thermal resistance is insufficient. The novelty of this work consists in assessing a new geo-polymeric FRCM-system by combining fly-ash binder (reused material) and expanded glass aggregate (recycled material). Direct tensile tests, for measuring the tensile strength, ultimate strain and elastic modulus, were performed in addition to thermal conductivity tests. The results were compared with those of traditional FRCM (commercially available). The potentiality of the proposal for structural and energy retrofitting is discussed and examples of its possible application are also reported. Full article

The increasing efforts aimed to design structures with reduced weight and better mechanical performances has led in recent years to a growing use of fiber reinforced polymer materials in several fields such as marine. However, these materials can be composed of chemically very different elements and, hence, may be difficult to joint. This research aims to improve the adhesion between a thermoplastic matrix of polyamide reinforced with short carbon fibers (PA12-CR) and a carbon fiber reinforced epoxy matrix (CFRP). Two different silane coupling agents, (3-Aminopropyl)trimethoxysilane (AM) and (3-Glycidyloxypropyl)trimethoxysilane (EP), were applied, through the spray deposition method, on the PA12-CR substrate to create a reactive layer between the adherents. Different deposition methods and coupling agents curing conditions were also investigated. The wettability of the PA12-CR surface as well as the chemical modifications induced by silane treatments were investigated through contact angle and Fourier Transform Infrared spectroscopy (FTIR) analyses. Furthermore, the interfacial adhesion between PA12-CR and CFRP substrates was evaluated through Mode I delamination tests (DCB). The effectiveness of the most promising treatment was finally verified on sandwich structures, having PA12-CR printed as internal core and CFRP laminates as external skins, through quasi-static three-point bending mechanical tests. Overall, the epoxy-based silane (EP) allowed significantly better resistance to the delamination up until the tensile failure of the CFRP substrate. Full article