Fibers, Volume 9, Issue 6 (June 2021) – 6 articles

The research described in this paper is dedicated to the use of continuous fibers as reinforcement for additive manufacturing, particularly using Shotcrete. Composites and in particular fiber reinforced polymers (FRP) are increasingly present in concrete reinforcement. Their corrosion resistance, high tensile strength, low weight, and high flexibility offer an interesting alternative to conventional steel reinforcement, especially with respect to their use in Concrete 3D Printing. This paper presents an initial development of a dynamic robot-based manufacturing process for FRP concrete reinforcement as an innovative way to increase shape freedom and efficiency in concrete construction. The focus here is on prefabricated fiber reinforcement, which is concreted in a subsequent additive process to produce load-bearing components. After the presentation of the fabrication concept for the integration of FRP reinforcement and the state of the art, a requirements analysis regarding the mechanical bonding behavior in concrete is carried out. This is followed by a description of the development of a dynamic fiber winding process and its integration into an automated production system for individualized fiber reinforcement. Next, initial tests for the automated application of concrete by means of Shotcrete 3D Printing are carried out. In addition, an outlook describes further technical development steps and provides an outline of advanced manufacturing concepts for additive concrete manufacturing with integrated fiber reinforcement. Full article

In this paper we report a low cost, simple, electrochemical method for large-area growth of single crystal ZnO nanorods. The method utilizes a metallic zinc foil as the source of the necessary zinc ions for ZnO growth on indium-doped tin oxide (ITO) glass slides. The method is thoroughly discussed and investigated varying all the parameters involved. The resulting ZnO nanorods are highly oriented along c-axis and densely packed, while their length and diameter can be tuned by varying the growth parameters. Two different types of seed layers on the ITO glass slides are tested. A seed layer made by spin coating of ZnO nanoparticles results in a twofold increase of the ZnO nanorod surface density as compared with a ZnO thin film seed layer by physical vapor deposition. Additionally, the effect of oxygen supply during electrodeposition was investigated as a crucial regulatory parameter not only for the geometrical and topological characteristics of the ZnO nano-arrays but for their physical properties as well. Full article

A nanofiber mesh was prepared for the adsorption of indoxyl sulfate (IS), a toxin associated with chronic kidney disease. Removing IS is highly demanded for efficient blood purification. The objective of this study is to develop a zeolite composite nanofiber mesh to remove IS efficiently. Eight zeolites with different properties were used for IS adsorption, where a zeolite with a pore size of 7 Å, H⁺ cations, and a silica to aluminum ratio of 240 mol/mol exhibited the highest adsorption capacity. This was primarily attributed to its suitable silica to aluminum ratio. The zeolites were incorporated in biocompatible poly (ethylene-co-vinyl alcohol) (EVOH) nanofibers, and a zeolite composite nanofiber mesh was successfully fabricated via electrospinning. The nanofiber mesh exhibited an IS adsorption capacity of 107 μg/g, while the adsorption capacity by zeolite increased from 208 μg/g in powder form to 386 μg/g when dispersed in the mesh. This also led to an increase in cell viability from 86% to 96%. These results demonstrated that this zeolite composite nanofiber mesh can be safely and effectively applied in wearable blood purification devices. Full article

We report on a scalable chirped-pulse Er-doped all-fiber laser, passively mode-locked by single-wall carbon nitride nanotubes. The average output power is ~15 mW, which corresponds to a peak power of ~77 W, and pulse energy of ~1.9 nJ and was achieved using a single amplification stage. We observed chirped-pulse generation with a duration of ~24.6 ps at a relatively low repetition rate of ~7.9 MHz, with a signal-to-noise ratio of ~69 dB. To characterize the short-term stability of the obtained regime, we have measured the relative intensity noise of the laser, which is <−107 dBc/Hz in the range of 3 Hz–1000 kHz. It should be noted that the standard deviation of root mean square of average power does not exceed a magnitude of 0.9% for 3 h of measurement. Full article

Oily wastewaters are considered as one of the most dangerous types of environmental pollution. In the present study, the microfiltration (MF) process of model emulsions and real oily wastewaters was investigated. For this purpose, capillary polypropylene (PP) membranes were used. The experiments were conducted under transmembrane pressure (TMP) and feed flow rate (V_F) equal to 0.05 MPa and 0.5 m/s, respectively. It was found that the used membranes ensured a high-quality permeate with turbidity equal to about 0.4 NTU and oil concentration of 7–15 mg/L. As expected, a significant decrease in the MF process performance was noted. However, it is shown that the initial decline of permeate flux could be slightly increased by increasing the feed temperature from 25 °C to 50 °C. Furthermore, Hermia’s models were used to interpret the fouling phenomenon occurring in studied experiments. It was determined that cake formation was the dominant fouling mechanism during filtration of both synthetic and real feeds. Through detailed studies, we present different efficient methods of membrane cleaning. Results, so far, are very encouraging and may have an important impact on increasing the use of polypropylene MF membranes in oily wastewater treatments. Full article

Polarization is measured very often to study the interaction of light and matter, so the description of the polarization of light beams is of both practical and fundamental interest. This review discusses the polarization properties of structured light in multimode graded-index optical fibers, with an emphasis on the recent advances in the area of spin-orbit interactions. The basic physical principles and properties of twisted light propagating in a graded index fiber are described: rotation of the polarization plane, Laguerre–Gauss vector beams with polarization-orbital angular momentum entanglement, splitting of degenerate modes due to spin-orbit interaction, depolarization of light beams, Berry phase and 2D and 3D degrees of polarizations, etc. Special attention is paid to analytical methods for solving the Maxwell equations of a three-component field using perturbation analysis and quantum mechanical approaches. Vector and tensor polarization degrees for the description of strongly focused light beams and their geometrical interpretation are also discussed. Full article