Next Article in Journal
Active Contour Model Using Fast Fourier Transformation for Salient Object Detection
Next Article in Special Issue
Analytical Current–Voltage Modeling and Analysis of the MFIS Gate-All-Around Transistor Featuring Negative-Capacitance
Previous Article in Journal
RCVC: RSU-Aided Cluster-Based Vehicular Clouds Architecture for Urban Areas
Previous Article in Special Issue
LTPS TFTs with an Amorphous Silicon Buffer Layer and Source/Drain Extension
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

A Study on the Effect of Bond Wires Lift-Off on IGBT Thermal Resistance Measurement

1
State Key Lab of Power Transmission Equipment & System Security and New Technology, School of Electrical Engineering, Chongqing University, Chongqing 400044, China
2
NXP (Chongqing) Semiconductors Co., Ltd., Chongqing 400044, China
*
Author to whom correspondence should be addressed.
Submission received: 19 November 2020 / Revised: 24 December 2020 / Accepted: 12 January 2021 / Published: 15 January 2021

Abstract

:
Bond wire lift-off will cause an increase of remaining wires’ power dissipation, which usually is ignored for healthy modules. However, only partial wires’ power dissipation transfers through thermal path from junction to case, which will lead to overestimate the whole power dissipation from collector to emitter pole and underestimate the calculated thermal resistance using the proportion of temperature difference to power dissipation. A FEM model is established to show the change of heat flow after bond wires were removed, the temperature of bond wires increases, and the measured thermal resistance decrease after bond wires lift-off. It is validated by experimental results using open package Insulated Gate Bipolar Transistor (IGBT) modules under different current conditions. This conclusion might be helpful to indicate the bond wires lift-off and solder fatigue by comparing the change of measured thermal resistance. Using the Kelvin setup to measure thermal resistance will cause misjudgment of failure mode due to the ignoring of wires’ power dissipation. This paper proposed that the lift-off of bond wires will lead to underestimating the thermal resistance measurement, which will overestimate the lifetime of IGBT module and misjudge its state of health.

1. Introduction

Insulated Gate Bipolar Transistors (IGBTs) are widely used in power converter, wind power generation, photovoltaic, aviation, and electric vehicles, hence its reliability has become one of the most important problems in applications [1].
Solder fatigue is one of the domain failure mechanisms in IGBT module [2], a previous study shows the aging of the solder layer causes a rise in junction-to-case thermal resistance [3]. Reference [4] suggested indicates solder fatigue by using a 20% increase in thermal resistance, which are widely used by researchers at present. Hence, thermal resistance is one of the most important indicators to evaluate the reliability of the IGBT module.
Figure 1 shows the structure and material of a wire-bonding IGBT, which consists of several layers of different materials, the thermal resistance of IGBT module consists of IGBT die Rdie, die-attached solder RD-S, DBC substrate RDBC, baseplate-attached solder RB-S and baseplate Rbase, as in (1). However, the different sizes and materials of each layer cause a heat spreading angle α between them [5]. This heat spreading angle leads that it is difficult to obtain thermal resistance Rth by using (2) [6]. The initial crack and void in the solder surface will also make the calculation of thermal resistance difficult [7].
R t h = R d i e + R D - S + R D B C + R B - S + R b a s e
R d λ × A o u t = d λ × ( a i n + 2 × d × tan α ) 2
JESD51-1 [8] proposed that the theoretical thermal resistance of semiconductor device Rth could be defined by the temperature difference between junction TJ and case TC divided by power dissipation P in steady-state, as in (3). This method could measure thermal resistance simply and effectively, which is widely used by many researchers.
R t h = T J T C P
Bond wires lift-off is one of the major failure mechanisms in IGBT module [9], previous researchers had studied a lot of effects of bond wires lift-off on gate voltage [10], conduct voltage [11], or threshold voltage [12]. However, there is still not much study on the effect of lift-off on thermal resistance measurement.
The power dissipation of die is far greater than bond wires, which is less than 3% in healthy module [13]. Therefore, the power dissipation of IGBT module is regarded as die power dissipation in thermal resistance measurement as in Figure 2.
Ref. [14] indicated that bond wires lift-off also leads to a rise in junction temperature, which means the power dissipation of wires also affect the thermal resistance calculation.
This paper proposes a study on the effect of bond wires lift-off on thermal resistance measurement. The effect of bond wire lift-off on thermal resistance measurement is presented in Section 2. A FEM model is established in Section 3 to show the change of bond wires’ heat flux after lift-off. This conclusion is validated by experimental results under different conditions in Section 4. Test results are discussed in Section 5. Section 6 concludes this paper.

2. Effect of Bond Wires Lift-Off on Thermal Resistance Measurement

The power dissipation of bond wires PWB is far smaller than the die in healthy module [13], hence the die power dissipation PD is the major heat source in healthy module as in (4).
P = P D + P W B P D P W B P P D
Usually, the case temperature is measured by the point below the die as in Figure 3. The temperature difference ΔT between junction and case is caused by theoretical thermal resistance and power dissipation in the vertical direction based on (4).
Δ T = T J T C = P D × R t h
Thus, the measured thermal resistance RJC_M could be extracted based on (3) and (4), which is equal to the theoretical thermal resistance of IGBT module.
R J C _ M = T J T C P = Δ T P D = R t h
Bond wires lift-off leads to a rise in power dissipation of remaining bond wires as in Figure 4a, which means the remaining wires become another heat source. The power dissipation of the remaining wires is shown in (7), where rWB_S is the resistance of a single bond wire, IC is conduction current, NWB is the number of total bond wires, and Nfail is the number of broken wires.
P W B = r W B _ S N W B N f a i l × I C 2
Figure 4b shows that the power dissipation of bond wires transfers to die side PWB_D and emitter side PWB_E, which is different from die’s heat flow as in (8).
P W B = P W B _ D + P W B _ E
Only PWB_D transfers through the die to the case point in the vertical direction. Hence the power dissipation P′ which affects the junction temperature could be obtained as (9).
P = P D + P W B _ D
The increased power dissipation leads to a rise in junction temperature after lift-off, as (10). Hence, the theoretical thermal resistance could be obtained as in (11) based on (3), (9) and (10).
Δ T = T J T C = P × R t h
R t h = T J T C P = Δ T P D + P W B _ D
Although the rise of junction temperature is caused by P, the total power dissipation of whole module PM is measured as the calculated power dissipation in thermal resistance measurement. The relationship between PM and P is shown in (12).
P M =   P   D + P W B = (   P   D + P W B _ D ) + P W B _ E =   P   + P W B _ E
Using the module’s power dissipation to measure thermal resistance will lead to a higher calculated power dissipation than the theoretical value. This difference between two power dissipation causes a reduction in measured results RJC-M after lift-off, which is lower than the theoretical value, as in (13).
R J C - M = Δ T P M = P × R t h P M = ( P M P W B _ E ) × R t h P M < R t h
Bond wires lift-off leads to a rise in power dissipation of remaining wires, while only part of power dissipation transfers through die to case point in the vertical direction. Hence, using the power dissipation of whole module will overestimate the power dissipation and underestimate thermal resistance. Then, this decrement will be more significant with the aging of bond wires.

3. Multiphysic-Modelling Simulation

3.1. Model Building

This paper built a multiphysics field finite-element-method (FEM) model based on a 1200V/50A silicon IGBT module WGL50B120F23 in COMSOL Multiphysics. Two IGBT dies cannot be turned on at the same time due to the half-bridge structure, hence only a single die turns on. The bond wires of diode and gate have been removed to improve computing speed. This FEM model is shown in Figure 5a.
Table 1 shows the material properties of FEM model. The electric conductivity of IGBT die is temperature-dependent which can be obtained based on the current-voltage curve [15]. Hence, the pure resistance rdie of IGBT die is calculated as in (14), where VCE_25 and VCE_150 are the conduct voltage at 25 °C and 150 °C at conduct current I. The electrical conductivity of die σ is calculated based on the chip size as in (15), where l, A and T are length, conduct area and temperature of IGBT die, respectively.
r d i e = V C E _ 25 I + V C E _ 150 V C E _ 25 I × ( 150 25 ) × ( T 25 )
σ = 1 r d i e × l A = 54.52 ( 1.5054 + T × 5.95 × 10 - 4 )
The ambient temperature sets at 25 °C. The ceramic and all boundaries are set as electric insulation except power supply and ground. A 40A DC source is defined as a terminal with the current source on the collector side and ground potential on the emitter side as electrical boundary conditions in the physical field of Electric Currents Physical Field. A convection coefficient of 3000 W/m2·K is defined on the bottom to simulate as forced air cooling [16] and the rest of the surfaces are defined as 12.5 W/m2·K in the physical field of Heat Transfer in Solids Physical Field. The meshed model is shown in Figure 5b, which consists of 114,813 domain elements, 51,252 boundary elements, and 7059 edge elements. This module is tested with and without bond wires removed.

3.2. Simulation Results

The temperature distributions of IGBT module are shown in Figure 6. The temperature distribution of IGBT module is almost the same after bond wires removed, while the maximum temperature of wires increases from 60.9 °C to 279.9 °C.
Figure 7 demonstrates the temperature distribution of die surfaces with different bond wires removed. The average temperature of die is similar after lift-off, where dashed line shows a rise in temperature of bonding area. The highest temperature on die increases from 69.6 °C to 75.2 °C after lift-off, which moved from the centre to bonding area.
Figure 8a demonstrates that there is a slowing rise in junction temperature while the temperature of wires increases rapidly after bond wires are removed. The power dissipation of FEM model with different bond wires removed is shown in Figure 8b. The power dissipation of die increases 0.1 W after 5 bond wires removed while power dissipation of bond wires grown six times than before at the same time. The proportion of bond wires power dissipation in IGBT module increase from 1.4% to 8.7% after bond wires removed due to the rise in bond wires’ resistance.
This result shows that power dissipation of IGBT module increase after lift-off, which is mainly caused by the remaining bond wires. This power dissipation of bond wires transfers through die after lift-off and causes a temperature rise.
The cross-sections of simulation results show how bond wires lift-off influence heat flow after bond wires removed, as in Figure 9. The major heat source is die in a healthy module while the heat flow mainly concentres under chip. The heat flow on emitter side rises a lot after wires removed, which is caused by the heat of wires dissipated through emitter side. Another part of bond wires power dissipation transfer through the die side to the case point. Hence, the die temperature is caused by die power dissipation and part of bond wires power dissipation in the vertical direction.
These simulation results using the power dissipation of whole module are summarized in Table 2. The lift-off of bond wire leads to a rise in power dissipation on remaining wires, which affects junction temperature, wire temperature, and case temperature. However, the measured thermal resistance shows the opposite results. The measured thermal resistance decrement could be calculated as in (16), where RJC_0 is the initial calculated thermal resistance before bond wires removed and RJC_1 is the calculated thermal resistance after bond wire lift-off. The measured thermal resistance decreases from 0.2591 K/W to 0.2416 K/W after bond wire lift-off, as in Figure 10.
Δ R J C R J C = R J C _ 1 R J C _ 0 R J C _ 0 × 100 %
These simulation results show that using the power dissipation of the whole module will lead to a decrease in thermal resistance measurement, which will be verified in Section 4.

4. Experimental Results on Bond Wires Lift-Off

4.1. Test Bench

A 1200V/50A IGBT modules from CETC with 6 bond wires on IGBT die 5SMY12H1280 is used in this study. The open package power module free of gel with black-painted is shown in Figure 11a. This module is tested with and without bond wires removal under different current levels. The main electrical circuit for test is shown in Figure 11b. The gate voltage is set at 15 V. A DC power supply is used to test IGBT under different current levels. The collector-emitter voltage is measured by an oscilloscope.
A Fan cooled heatsink from GD Rectifiers PS260/xxF is used in this test, as in Figure 12a. Two graves are incised on the top of the heatsink to place thermal couples, which are used to measure case temperature in a thermocouple data logger (TC08) from PicoLog. A thin thermal pad is attached to the baseplate to reduce air gap between the heatsink and IGBT. The die temperature is measured by an IR camera (Flir A310) above IGBT. This test bench is shown in Figure 12b.
Figure 13a shows that there is a thermal pad between baseplate and heatsink, hence the measured thermal resistance consists of IGBT module RJC thermal pad RTP. There are no other conditions change except bond wires and current levels during detection, the measured thermal resistance RJC_M is equivalent to the junction to case thermal resistance, as in (17).
R J C _ M = ( T J T C ) / P = R J C + R T P
Ref. [14] indicated that it is difficult to detect average die temperature after bond wires lift-off due to the sharp rise of temperature in the bonding area. However, some researchers [17,18] proposed that die temperature could be measured by a line across die after bond wires removed. Hence, this measured method in this paper is shown in Figure 13b, where the temperature of die and the bond wires are measured by mean temperature of line and square. The bond wires are cut from right to left to simulate the aging of bond wires.

4.2. Results Analysis

Figure 14a shows the power dissipation of IGBT module after bond wires removed. The power dissipation increases from 10.87 W to 11.36 W at 10 A after 5 bond wires removed. The power dissipation shows a similar rise at 20 A which is more significant at higher current. The power dissipation increases from 45.3 W to 52.4 W at 30 A with 5 wires removed. Although IGBT bond wire suffers thermal runaway failure at 40 A, it shows a rise of 5 W after 4 bond wires removed.
Figure 14b shows the temperature of die and bond wires under each condition based on Figure 13b, where solid lines are die temperatures and dashed lines are bond wires temperatures. It can be observed that the junction temperature increases slightly while wires temperature rises a lot after bond wires removed. Although bond wire temperature is lower than die at the initial stage, it exceeds die temperature and reaches a higher temperature after bond wires removed.
The slight rise of temperature difference between junction and case indicates that power dissipation increases in the vertical direction, which is caused by an increase of bond wires power dissipation after bond wires removed, as in Figure 14c. The temperature difference stays around 3.6 at 10 A. These results still show a slight rise of 0.2 °C at 20 A. The rise is more significant at higher current due to higher power dissipation of bond wires, which shows a rise of 1 °C.
The power dissipation of bond wires transfers to die side and emitter side, which is affected by the temperatures of two sides. These temperature measuring positions of two sides are shown in Figure 15a. These measured results are shown in Figure 15b, where solid lines are emitter side temperatures and dashed lines are die side temperatures. Although the emitter side temperature increases a bit after bond wires removed, the die side temperature is far higher than the emitter side due to die power dissipation. Hence, most of the heat generated by the bond wires will transfer to emitter side due to its lower temperature according to the second law of thermodynamics.
The temperature differences between the two sides of bond wires are shown in Figure 15c. The temperature difference increases slightly at low current after bond wires removed. However, this temperature difference shows a significant rise after bond wires removed under higher current levels, which increase from 12.7 °C to 16.6 °C at 30 A with 5 wires removed as 20.1 °C to 25.8 °C at 40 A with four wires removed. The last remaining wire at 30 A even shows a substantial rise of 25.5 °C, which is far higher than initial states.
The uneven temperature distribution on both sides of wires leads extremely difficult to divide the bond wires power dissipation into PWB_E and PWB_D, which is not constant for each condition. Hence, it is nearly impossible to calculate the theoretical power dissipation in the vertical direction, which means the measurements of thermal resistance after bond wires lift-off will not be accurate after lift-off.
The operation of the IGBT surface under 30 A with different broken bond wires is demonstrated by IR images in Figure 16, where Ar1 and Li1 are the temperatures of wires and die. Initially, the junction temperature is higher than bond wires temperature, as in Figure 16a,b. The wires get hotter and show higher maximum temperature than die after several wires removed, as in Figure 16c,d. Finally, the average temperature of bond wires is higher than die with far greater maximum temperature, as in Figure 16e,f.
The measured junction-to-case thermal resistance after bond wires removed is shown in Figure 17, where solid lines are measured thermal resistance and dashed lines are decrement. The first two bond wires removed show a small effect on thermal resistance measurement due to the small power dissipation increase at the initial stage. Then, the thermal resistance decrement is 1.3% with three bond wires removed. Compared with the initial value, the thermal resistance decreases to 2.8% with four bond wires removed, which finally reaches 5% with only one remaining wire. Although the initial measured thermal resistances are different for each current level, they all show a similar decreasing trend after bond wires removed. The obtained values are summarized in Table 3.

5. Discussion

5.1. Factors affecting Thermal Resistance Measurement

JESD51-1 proposes to measure an accurate measurement of thermal resistance with at least 20 °C temperature rise on die. The measured results are more accurate at higher current due to the larger temperature rise on die. However, the temperature rise is far less than 20 °C at low current level due to small power dissipation, which also makes it difficult to detect the change of case temperature.
The test results show similar results at higher current while thermal resistance decrement is more significant at 10 A, which is caused by inaccuracy junction temperature measurement at small current. The open package structure might lead to heat spreading for all dimensions [19] and cause a change in thermal resistance measured. These reasons finally cause different initial thermal resistance.
This paper shows that only part of bond wires’ power dissipation transfers to die side after bond wires lift-off. Hence some temperature sensitivity detection methods, which use whole module’s conduct voltage [20] or gate voltage [17], will get a higher result after bond wires lift-off. Those methods which propose to use dynamic time characteristics to measure junction temperatures, such as turn-on delay [21] and turn-off delay [22], could provide accurate results after bond wire lift-off.

5.2. Using Die Power Dissipation to Measure Thermal Resistance

Although Figure 18 shows that the Kelvin setup could measure the die power dissipation from Collector terminal C and Auxiliary emitter terminal e, it still leads to a confusing result in thermal resistance measurement.
The die power dissipation is smaller than the theoretical power dissipation in the vertical direction, which ignored the effect of PWB_D on junction temperature. Thus, using the die power dissipation as the calculated power dissipation will lead to a rise in measured thermal resistance RJC-M as in (18).
R J C - M = Δ T P D = P × R t h P d = ( P D + P W B _ D ) × R t h P D > R t h
The measured thermal resistance of FEM model by using die power dissipation is shown in Figure 19. The measured thermal resistance increases after bond wires removed, which shows similar performance as solder fatigue. These results are caused by ignoring of wires’ power dissipation. Hence, using the Kelvin setup to measure thermal resistance will cause misjudgment of failure mode.

5.3. Failure Criteria Based on Thermal Resistance Decrement

Ref. [23] proposed to use a 5% rise in conduct voltage as the failure criteria of bond wires, which are widely used by lots of researchers [14,24,25] to indicate the failure of bond wires. However, it is still very difficult to distinguish the failure of bond wires due to the similar performance as solder fatigue. However, this feature of decrement in thermal resistance measurement might be useful in fault detection.
The measured thermal resistances at failure critical under each current level are shown in Table 4. The difference between decrement of each current condition is caused by the remaining wires at failure criteria, which shows 1 wire remains at lower current and 2 wires remain at higher current.
Although the test results show that the decrement at the failure point is different for each current level, they show the opposite results of solder fatigue. The solder fatigue of IGBT modules increases die power dissipation [26], which also leads to a rise in the module’s power dissipation. However, the calculated thermal resistance increases after solder fatigue, which is different from bond wires lift-off, as in Figure 20. These different effects of two aging processes on thermal resistance measurement might be helpful to indicate the failure of IGBT bond wires lift-off and solder fatigue by using the rising and falling of measured results.

6. Conclusions

This paper proposes a study on the effect of bond wire lift-off on thermal resistance measurement. The analysis leads to following conclusions:
(1) Bond wire lift-off leads to a rise in power dissipation of remaining bond wires, and the power dissipation transfers through the die side and emitter side respectively. However, only part of the power dissipation passing through the die will cause the junction temperature to rise. Hence, the thermal resistance will be underestimated because the power dissipation is overestimated when using the power dissipation of whole module to calculate the thermal resistance.
(2) In the tests, the thermal resistance is measured under different current conditions with and without bond wires removed. Measured results are compared with the initial value, which all show a decrease after bond wires removed. Reference [3] indicated that even a 0.5% increase of thermal resistance could lead to a significant impact on lifetime estimation. This paper proposed that the lift-off of bond wires will lead to underestimating the thermal resistance measurement, which will overestimate the lifetime of IGBT module and misjudge its state of health. Thus, the effect of bond wires lift-off on thermal resistance measurement needs to be taken seriously to improve the reliability of IGBT module.
(3) This paper proposed that the decrement of thermal resistance calculated is caused by bond wires lift-off, which is opposite to solder fatigue. Hence, the changes in thermal resistance measurement might be helpful to distinguish fatigue of IGBT module under different conditions. In future work, the detection method of bond wires fatigue based on thermal resistance decrement will be further studied to avoid the open-circuit fault of IGBT module.

Author Contributions

Conceptualization, methodology, validation and writing—original draft preparation, D.L.; writing, review and editing, W.L., H.X., X.D. and Z.D.; supervision, W.L. and M.C. All authors have read and agreed to the published version of the manuscript.

Funding

This research was supported by the National Key Research and Development Program of China (grant numbers 2018YFB0905800); the National Natural Science Foundation of China (grant numbers 51707024); the Fundamental Research Funds for the Central Universities Project (No.2020CDJQY-A026) and the National “111” Project (B08036).

Data Availability Statement

The data presented in this study are available on request from the corresponding author.

Acknowledgments

The authors would like to thank Li Ran, Ruizhu Wu, Borong Hu, and Xuan Guo at the University of Warwick for the help and advice.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Yang, S.; Bryant, A.; Mawby, P.; Xiang, D.; Ran, L.; Tavner, P. An Industry-Based Survey of Reliability in Power Electronic Converters. IEEE Trans. Ind. Appl. 2011, 47, 1441–1451. [Google Scholar] [CrossRef]
  2. Lai, W.; Chen, M.; Ran, L.; Xu, S.; Jiang, N.; Wang, X.; Alatise, O.; Mawby, P. Experimental Investigation on the Effects of Narrow Junction Temperature Cycles on Die-Attach Solder Layer in an IGBT Module. IEEE Trans. Power Electron. 2017, 32, 1431–1441. [Google Scholar] [CrossRef]
  3. Lai, W.; Chen, M.; Ran, L.; Alatise, O.; Xu, S.; Mawby, P. Low Stress Cycle Effect in IGBT Power Module Die-Attach Lifetime Modeling. IEEE Trans. Power Electron. 2016, 31, 6575–6585. [Google Scholar] [CrossRef]
  4. Scheuermann, U. Reliability of pressure contacted intelligent integrated power modules. In Proceedings of the 14th International Symposium on Power Semiconductor Devices and Ics, Nuremberg, Germany, 7 June 2002; pp. 249–252. [Google Scholar] [CrossRef]
  5. Lostetter, A.; Barlow, F.; Elshabini, A. An overview to integrated power module design for high power electronics packaging. Microelectron. Reliab. 2000, 40, 365–379. [Google Scholar] [CrossRef]
  6. Wang, Z.; Qiao, W.; Qu, L. A Real-Time Adaptive IGBT Thermal Model Based on an Effective Heat Propagation Path Concept. IEEE J. Emerg. Sel. Top. Power Electron. 2020, 1. [Google Scholar] [CrossRef]
  7. Li, J.; Yaqub, I.; Corfield, M.; Johnson, C.M. Interconnect Materials Enabling IGBT Modules to Achieve Stable Short-Circuit Failure Behavior. IEEE Trans. Compon. Packag. Manuf. Technol. 2017, 7, 734–744. [Google Scholar] [CrossRef] [Green Version]
  8. INTEGRATED CIRCUIT THERMAL MEASUREMENT METHOD—ELECTRICAL TEST METHOD. Available online: https://www.jedec.org/standards-documents/docs/jesd-51-1 (accessed on 1 December 1995).
  9. Baker, N.; Liserre, M.; Dupont, L.; Avenas, Y. Improved Reliability of Power Modules: A Review of Online Junction Temperature Measurement Methods. IEEE Ind. Electron. Mag. 2014, 8, 17–27. [Google Scholar] [CrossRef] [Green Version]
  10. Zhou, L.; Zhou, S.; Xu, M. Investigation of gate voltage oscillations in an IGBT module after partial bond wires lift-off. Microelectron. Reliab. 2013, 53, 282–287. [Google Scholar] [CrossRef]
  11. Smet, V.; Forest, F.; Huselstein, J.-J.; Rashed, A.; Richardeau, F. Evaluation of Vce Monitoring as a Real-Time Method to Estimate Aging of Bond Wire-IGBT Modules Stressed by Power Cycling. IEEE Trans. Ind. Electron. 2012, 60, 2760–2770. [Google Scholar] [CrossRef]
  12. Mandeya, R.; Chen, C.; Pickert, V.; Naayagi, R.; Ji, B. Gate–Emitter Pre-threshold Voltage as a Health-Sensitive Parameter for IGBT Chip Failure Monitoring in High-Voltage Multichip IGBT Power Modules. IEEE Trans. Power Electron. 2018, 34, 9158–9169. [Google Scholar] [CrossRef] [Green Version]
  13. Choi, U.; Blaabjerg, F. Separation of Wear-Out Failure Modes of IGBT Modules in Grid-Connected Inverter Systems. IEEE Trans. Power Electron. 2017, 33, 6217–6223. [Google Scholar] [CrossRef]
  14. Ji, B.; Pickert, V.; Cao, W.; Zahawi, B. In Situ Diagnostics and Prognostics of Wire Bonding Faults in IGBT Modules for Electric Vehicle Drives. IEEE Trans. Power Electron. 2013, 28, 5568–5577. [Google Scholar] [CrossRef] [Green Version]
  15. Gao, B.; Yang, F.; Chen, M.; Ran, L.; Ullah, I.; Xu, S.; Mawby, P. A Temperature Gradient-Based Potential Defects Identification Method for IGBT Module. IEEE Trans. Power Electron. 2017, 32, 2227–2242. [Google Scholar] [CrossRef]
  16. Bahman, A.S.; Ma, K.; Blaabjerg, F. A Lumped Thermal Model Including Thermal Coupling and Thermal Boundary Conditions for High-Power IGBT Modules. IEEE Trans. Power Electron. 2018, 33, 2518–2530. [Google Scholar] [CrossRef]
  17. Baker, N.; Dupont, L.; Munk-Nielsen, S.; Iannuzzo, F.; Liserre, M. IR Camera Validation of IGBT Junction Temperature Measurement via Peak Gate Current. IEEE Trans. Power Electron. 2017, 32, 3099–3111. [Google Scholar] [CrossRef] [Green Version]
  18. Dupont, L.; Avenas, Y.; Jeannin, P.-O. Comparison of Junction Temperature Evaluations in a Power IGBT Module Using an IR Camera and Three Thermosensitive Electrical Parameters. IEEE Trans. Ind. Appl. 2013, 49, 1599–1608. [Google Scholar] [CrossRef] [Green Version]
  19. Schweitzer, D.; Pape, H.; Chen, L. Transient Measurement of the Junction-To-Case Thermal Resistance Using Structure Functions: Chances and Limits. In Proceedings of the Twenty-Third Annual IEEE Semiconductor Thermal Measurement and Management Symposium, San Jose, CA, USA, 16–20 March 2008; pp. 191–197. [Google Scholar]
  20. Perpina, X.; Serviere, J.; Saiz, J.; Barlini, D.; Mermet-Guyennet, M.; Millán, J. Temperature measurement on series resistance and devices in power packs based on on-state voltage drop monitoring at high current. Microelectron. Reliab. 2006, 46, 1834–1839. [Google Scholar] [CrossRef]
  21. Harald, K.; Axel, M. On-line junction temperature measurement of IGBTs based on temperature sensitive electrical parameters. In Proceedings of the 2009 13th European Conference on Power Electronics and Applications, Barcelona, Spain, 8–10 September 2009; pp. 2249–2258. [Google Scholar]
  22. Luo, H.; Chen, Y.; Sun, P.; Li, W.; He, X. Junction Temperature Extraction Approach with Turn-off Delay Time for High-voltage High-Power IGBT Modules. IEEE Trans. Power Electron. 2015, 31, 1. [Google Scholar] [CrossRef]
  23. Held, M.; Jacob, P.; Nicoletti, G.; Scacco, P.; Poech, M.-H. Fast power cycling test of IGBT modules in traction application. In Proceedings of the Second International Conference on Power Electronics and Drive Systems, Singapore, 26–29 May 1997; pp. 425–430. [Google Scholar]
  24. Andreas, B. A Novel Test Method for Minimising Energy Costs in IGBT Power Cycling Studies. Ph.D Thesis, University of the Witwatersrand, Johannesburg, South African, 2006. [Google Scholar]
  25. Wei, K.; Du, M.; Xie, L.; Li, J. Study of Bonding Wire Failure Effects on External Measurable Signals of IGBT Module. IEEE Trans. Device Mater. Reliab. 2012, 14, 83–89. [Google Scholar] [CrossRef]
  26. Lai, W.; Chen, M.; Ran, L.; Xu, S.; Qin, H.; Alatise, O.; Mawby, P.A. Study on the lifetime characteristics of power modules under power cycling conditions. IET Power Electron. 2016, 9, 1045–1052. [Google Scholar] [CrossRef]
Figure 1. Structure of a wire-bonding Insulated Gate Bipolar Transistors (IGBT) module.
Figure 1. Structure of a wire-bonding Insulated Gate Bipolar Transistors (IGBT) module.
Electronics 10 00194 g001
Figure 2. Power dissipation of IGBT module.
Figure 2. Power dissipation of IGBT module.
Electronics 10 00194 g002
Figure 3. Thermal network in healthy module.
Figure 3. Thermal network in healthy module.
Electronics 10 00194 g003
Figure 4. (a) Power dissipation of IGBT module (b) Thermal network after lift-off.
Figure 4. (a) Power dissipation of IGBT module (b) Thermal network after lift-off.
Electronics 10 00194 g004
Figure 5. (a) FEM model of IGBT module (b) Meshed FEM model.
Figure 5. (a) FEM model of IGBT module (b) Meshed FEM model.
Electronics 10 00194 g005
Figure 6. Temperature distribution of IGBT module with different bond wires removed under 40 A (a) 0 wire (b) 1 wire (c) 2 wires (d) 3 wires (e) 4 wires (f) 5 wires.
Figure 6. Temperature distribution of IGBT module with different bond wires removed under 40 A (a) 0 wire (b) 1 wire (c) 2 wires (d) 3 wires (e) 4 wires (f) 5 wires.
Electronics 10 00194 g006
Figure 7. Junction temperature distribution of IGBT die with different wires removed under 40 A (a) 0 wire (b) 1 wire (c) 2 wires (d) 3 wires (e) 4 wires (f) 5 wires.
Figure 7. Junction temperature distribution of IGBT die with different wires removed under 40 A (a) 0 wire (b) 1 wire (c) 2 wires (d) 3 wires (e) 4 wires (f) 5 wires.
Electronics 10 00194 g007
Figure 8. (a) Temperature of die and wires after bond wires removed (b) Power dissipation of die and wires after bond wires removed.
Figure 8. (a) Temperature of die and wires after bond wires removed (b) Power dissipation of die and wires after bond wires removed.
Electronics 10 00194 g008
Figure 9. Sectional drawing of the heat flow in IGBT module with and without wires removed.
Figure 9. Sectional drawing of the heat flow in IGBT module with and without wires removed.
Electronics 10 00194 g009
Figure 10. Measured thermal resistance using module’s power dissipation.
Figure 10. Measured thermal resistance using module’s power dissipation.
Electronics 10 00194 g010
Figure 11. (a) Open package IGBT module, black-painted (b) Main electrical circuit.
Figure 11. (a) Open package IGBT module, black-painted (b) Main electrical circuit.
Electronics 10 00194 g011
Figure 12. (a) Heatsink (b) Test environment.
Figure 12. (a) Heatsink (b) Test environment.
Electronics 10 00194 g012
Figure 13. (a) Measured thermal resistance (b) Measured method.
Figure 13. (a) Measured thermal resistance (b) Measured method.
Electronics 10 00194 g013
Figure 14. Measured results after bond wires removed (a) Power dissipation of IGBT module (b) Temperature of die and bond wires (c) Temperature difference between die and case.
Figure 14. Measured results after bond wires removed (a) Power dissipation of IGBT module (b) Temperature of die and bond wires (c) Temperature difference between die and case.
Electronics 10 00194 g014
Figure 15. (a) Temperature measuring positions of bond wires two sides (b) Measured temperature of bond wires two sides (c) Temperature difference between two sides of bond wires.
Figure 15. (a) Temperature measuring positions of bond wires two sides (b) Measured temperature of bond wires two sides (c) Temperature difference between two sides of bond wires.
Electronics 10 00194 g015
Figure 16. Thermal images of an IGBT device under 30 A with different wires removed (a) 0 wire (b) 1 wire (c) 2 wires (d) 3 wires (e) 4 wires (f) 5 wires.
Figure 16. Thermal images of an IGBT device under 30 A with different wires removed (a) 0 wire (b) 1 wire (c) 2 wires (d) 3 wires (e) 4 wires (f) 5 wires.
Electronics 10 00194 g016
Figure 17. Measured thermal resistance after bond wires lift-off.
Figure 17. Measured thermal resistance after bond wires lift-off.
Electronics 10 00194 g017
Figure 18. Power dissipation of IGBT module using Kelvin setup.
Figure 18. Power dissipation of IGBT module using Kelvin setup.
Electronics 10 00194 g018
Figure 19. Measured thermal resistance using die power dissipation.
Figure 19. Measured thermal resistance using die power dissipation.
Electronics 10 00194 g019
Figure 20. Effect of failure mechanism on thermal resistance measurement (a) bond wires lift-off (b) solder fatigue.
Figure 20. Effect of failure mechanism on thermal resistance measurement (a) bond wires lift-off (b) solder fatigue.
Electronics 10 00194 g020
Table 1. Material Properties of FEM Model.
Table 1. Material Properties of FEM Model.
PartMaterialsDensity [kg/m3]Electric Conductivity [S/m]Thermal Conductivity
[W/(m·K)]
Bond wiresAluminium27003.5 × 107237
DieSilicon2329σ124
Solder96.5Sn3.5Ag74009.1 × 10635
BaseplateCopper89606 × 107380
InsulationAl2O3378030
Table 2. Simulation results.
Table 2. Simulation results.
Wires Removed012345
TJ (°C)63.964.064.264.464.865.6
TJmax (°C)68.668.869.269.570.375.2
Twire (°C)60.962.566.175.5105.2279.9
TC (°C)45.6545.7745.9246.0246.4647.25
P (W)70.2970.5370.9471.6272.8475.94
RJC (K/W)0.25910.25840.25720.25650.25120.2416
ΔRJC/RJC (%)0–0.28–0.74–1.01–3.07–6.78
Table 3. Thermal resistance (K/W) under different working conditions after bond wires removed.
Table 3. Thermal resistance (K/W) under different working conditions after bond wires removed.
Current0 Wire Fail1 Wire Fail2 Wires Fail3 Wires Fail4 Wires Fail5 Wires Fail
10 A0.34220.33820.33120.32360.31740.3125
0.00%–1.17%–3.22%–5.44%–7.25%–8.69%
20 A0.35890.35690.35540.35440.34940.3390
0.00%–0.57%–1.00%–1.26%–2.65%–5.57%
30 A0.39200.39180.39020.38680.38090.3728
0.00%–0.05%–0.45%–1.32%–2.83%–4.90%
40 A0.42550.42350.42200.41800.4133
0.00%–0.48%–0.82%–1.75%–2.88%
Table 4. Failure Criteria of Bond Wires Lift-Off.
Table 4. Failure Criteria of Bond Wires Lift-Off.
Conduct CurrentInitial Voltage5% Voltage
Increase
Failure VoltageWires RemainThermal Resistance Decrement
10 A1.0871.14141.1361–8.69%
20 A1.3151.38081.4221–5.57%
30 A1.5111.58661.592–2.83%
40 A1.7081.79341.8332–2.88%
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Luo, D.; Chen, M.; Lai, W.; Xia, H.; Ding, X.; Deng, Z. A Study on the Effect of Bond Wires Lift-Off on IGBT Thermal Resistance Measurement. Electronics 2021, 10, 194. https://0-doi-org.brum.beds.ac.uk/10.3390/electronics10020194

AMA Style

Luo D, Chen M, Lai W, Xia H, Ding X, Deng Z. A Study on the Effect of Bond Wires Lift-Off on IGBT Thermal Resistance Measurement. Electronics. 2021; 10(2):194. https://0-doi-org.brum.beds.ac.uk/10.3390/electronics10020194

Chicago/Turabian Style

Luo, Dan, Minyou Chen, Wei Lai, Hongjian Xia, Xueni Ding, and Zhenyu Deng. 2021. "A Study on the Effect of Bond Wires Lift-Off on IGBT Thermal Resistance Measurement" Electronics 10, no. 2: 194. https://0-doi-org.brum.beds.ac.uk/10.3390/electronics10020194

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop