Next Article in Journal
Towards Safer Primers: A Review
Previous Article in Journal
Psychosocial Impact of Powered Wheelchair, Users’ Satisfaction and Their Relation to Social Participation
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Open Source Waste Plastic Granulator

1
Department of Mechanical Engineering–Engineering Mechanics, Michigan Technological University, Houghton, MI 49931, USA
2
Department of Electrical & Computer Engineering, Michigan Technological University, Houghton, MI 49931, USA
3
Department of Material Science & Engineering, Michigan Technological University, Houghton, MI 49931, USA
4
Department of Electronics and Nanoengineering, School of Electrical Engineering, Aalto University, FI-00076 Espoo, Finland
*
Author to whom correspondence should be addressed.
Submission received: 30 August 2019 / Revised: 7 October 2019 / Accepted: 9 October 2019 / Published: 14 October 2019
(This article belongs to the Section Innovations in Materials Processing)

Abstract

:
In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built, and tested for its ability to convert post-consumer waste, 3D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404 W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than $2000 USD in materials. The experimentally measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, maker space, fab lab, or small business–based distributed recycling.

Graphical Abstract

1. Introduction

The open-source release of the self-replicating rapid prototyper (RepRap) 3D printer [1,2,3] greatly expanded access to additive manufacturing (AM) because of several orders of magnitude reduction in costs [4]. As open-source RepRap 3D printers spawned hundreds of clones, fused filament fabrication (FFF) enabled a shift in the trend from centralized to consumer (or prosumer) distributed manufacturing [4,5,6,7,8]. Consumers now use RepRaps or pre-built desktop 3D printers to manufacture all manner of products from toys to household items less expensively than purchasing them from conventional brick and mortar or online retailers [9,10,11]. The peer-reviewed business literature now recognizes this potential shift in manufacturing [12,13,14], which is brought on not only by the open source sharing of 3D printer designs, but now more importantly because of millions of freely shared digital designs of other products that are 3D printable [9]. Any level of consumer from scientific research funders to arthritis patients [15] can earn a high return on investment (ROI) [16] for distributed manufacturing with commercial polymer 3D printing filament based on downloaded substitution values [17]. However, commercial 3D printing filament is still sold for roughly an order of magnitude more than the cost of the raw materials of virgin plastic pellets (e.g., $15–100 USD/kg vs $1–10 USD/kg). This has reduced adoption of AM at the prosumer level [18]. There are two methods to overcome this artificial cost barrier for wider spread distributed manufacturing: (1) use distributed recycling to make filament and (2) skip the entire process of fusing filament into a 3D printed object by printing directly from polymer granules, shards or particles.
Three-dimensional printing filament can be manufactured economically using distributed means with an open source waste plastic extruder (often called a recyclebot) [19]). Recycling is well-known to be environmentally beneficial, and performing distributed recycling of plastic waste into filament decreases the embodied energy of filament by 90% compared to traditional centralized filament manufacturing using fossil fuels as inputs [20,21,22]. Using distributed recycling fits into the circular economy paradigm [23,24,25,26] as it eliminates most embodied energy and pollution from transportation between processing steps. Many open-source commercial and non-commercial recyclebots have been developed [27], including a 3D printable version [28]. Many research groups and companies have demonstrated that pre-consumer and post-consumer waste polymers can be recycled into 3D printing filaments, including
  • polylactic acid (PLA) [28,29,30,31,32];
  • acrylonitrile butadiene styrene (ABS) [24,33,34,35,36];
  • high-density polyethylene (HDPE) [19,37,38];
  • polypropylene (PP) [38];
  • polystyrene (PS) [38];
  • polyethylene terephthalate (PET) [39];
  • linear low-density polyethylene (LLDPE) and low-density polyethylene (LDPE) [40];
  • elastomers [8].
In addition, filaments can be made from polymer composites using carbon-reinforced plastic [41] and various types of waste wood [42,43]. Unfortunately, each melt-solidification degrades the mechanical properties of the resultant 3D print [44,45], so recycling is limited to about five cycles [29,30,46] or using chemical recycling [47] without use some means of reinforcement or blending with virgin materials. The potential for such distributed recycling could be either completely distributed (where the consumer recycles their own plastic in their home or business) or part of a local closed-loop supply chain [48].
The second method, however, eliminates the need for filament entirely, as 3D printers have been developed that can print directly from particles, pellets, flakes, regrind, or shreds of recycled plastic. These fused particle fabrication (FPF) or fused granular fabrication (FGF) 3D printers are becoming established in the academic [49,50,51,52,53,54], maker [55,56,57], and commercial venues (e.g., GigabotX, PartDaddy, Cheetah Pro, David, Erecto-Struder, etc.). FPF/FGF printing is possible with recycled materials [58,59,60], as is using FGF printing of molds for distributed injection molding of larger replicate products [60].
Both the widespread deployment of distributed recycling with recyclebots and FPF/FGF are being restricted because of the lack of accessibility of low-cost pelletizers and choppers to turn post-consumer plastic products into polymer feedstock. In general, these are large industrial machines not conducive for makerspaces, fab labs, research, or consumer use because of their high throughputs, noise, and capital costs. This study attempts to a provide a new low-cost but medium-scale technology for transforming plastic recyclables into usable 3D printing feedstock in the form of granules (or particles). In order to provide a low-cost tool for making polymer feedstock from post-consumer waste this study follows the open-source hardware design paradigm [61,62], which has proven so successful for 3D printing in general. A novel open source waste plastic granulator system is designed, built, and tested for its ability to convert post-consumer waste, 3D printed products, and 3D printer waste into polymer feedstock for recyclebots of FGF/FPF printers. Then, the technical specifications of the device are quantified in terms of power consumption and particle size of the output. In order for the device to operate in a fab lab (or similar environment), a noise reduction system is designed, added, and analyzed. The results are presented and discussed.

2. Design Concept

The design of the open source waste plastic granulator system is divided into four separate sub-systems, each responsible for parts of the machine that serve a specific function.
  • Power Transmission: This system encompasses all machine parts needed to convert the electrical energy being input to the system into mechanical energy, as well as transmit that mechanical energy to the plastic cutting/granulation system.
  • Plastic Cutting/Granulation: This system is the one that directly interacts with the plastic in order to cut it into small chunks. It is responsible for cutting plastic as well as ejecting granules after they have reached a uniform size.
  • Material Guidance/Structural: This system involves any parts that keep the plastic feedstock inside of the proper cutting area during operation or guide the feedstock during its journey. It includes the hopper chute, the hopper lip, the granulation chamber lip, any mechanism used to hold the hopper to the granulation chamber, and the upper surfaces of the granulation chamber.
  • Electrical: This system encompasses all of the components required to convert electrical energy from electrical grid power into rotational energy, as well as any other electrical peripherals present on the machine. This includes the electrical box, safety switches, circuit board, motor, and a microcontroller.
Together, these systems operate with the end goal of transforming plastic recyclables into usable 3D printing feedstock in the form of granules (or particles). The main concepts and parts in each sub-system will be described, but the full open hardware details including the bill of materials (BOM), drawings for custom parts, CAD files, build instructions, and design reports of previous versions are housed at the Open Science Framework [63].

2.1. Power Transmission System

The power transmission system transfers rotational mechanical energy from the motor spindle to the cutting rotor shaft. As a first step towards designing this subsystem of the machine the design team made the decision that a one-phase AC motor (IronHorse, Automation Direct, Cumming, GA, USA; 1–1/2hp 115/230 VAC motor, with 15.9mm shaft diameter wired for 230 V) would be used to supply mechanical power to the machine. This method of mechanical power delivery is the most reliable and easiest way for an individual to drive a machine from their home circuitry. Pulleys and belts are used to convey power to the cutting rotor; belts are not only inexpensive when compared to a gearbox but are also more user friendly since they are easy to install, maintain, and adjust once assembled. An isolated view of the 3D model for the power transmission subsystem and all of its components can be seen in Figure 1.
As seen in the Figure 1, the parts of the power transmission system are as follows: AC Motor, pulleys, belts, flange-mount bearings, rotor shaft, quick-disconnect (QD) bushings, and weld-on hubs (plus mounting hardware). The motor selected to drive the granulator is a 1.5 HP motor with a spindle speed of ~1800 RPM. On a previous version of the open source waste plastic granulator, the optimal rotor speed for cutting was found to be around 750 RPM [62]; this speed was also used for this design as well, leading to a set ratio of pulley diameters of about 1:2.4. A 100.33 mm diameter pulley was chosen to connect to the motor spindle using a quick-disconnect style bushing. A 222.25 mm diameter pulley was used to attach to the cutting rotor shaft, also with a quick-disconnect bushing. Both pulleys have two channels for v-belts to ensure there is no slippage during operation. In order to keep the cutting rotor shaft spinning about its major axis, two large flange-mount bearings were used. In order to connect the shaft to the cutting rotor, QD bushings were used in conjunction with weld-on hubs to clamp to the shaft. These components were then bolted to the cutting rotor so that the blades would spin with the shaft (see Figure 2).

2.2. Plastic Cutting System

The plastic cutting subsystem is, out of all of the subsystems, the most directly related to the overall function of the machine as it is responsible for transforming plastic waste/recyclables into granules of a specific size. In order to do this, the design team picked out many different forms that would satisfy the subsystem’s purpose and compared them using a decision matrix (details of which are found in the OSF database [63]). From the decision matrix, the best option was found to be the fly knife design, consisting of two large rotating blades (fly knives) that pass close to a fixed blade during operation (Figure 2). Shear force on the plastic between the blades is the main cutting method.
The plastic cutting system consists of four separate components (plus mounting hardware). Two blade arms will connect to the cutting rotor shaft (shown in Figure 2) and will spin with the shaft. Connected to either end of each blade arm in the configuration shown below are two fly knives, which will contact the plastic within the cutting chamber and shear through it. To help with the cutting of the plastic granules, there are two more pieces in this system that both interact with the rotating fly knives, the granulation screen and the bed blade. As the fly knives rotate in the granulation chamber, they will pass very close to the fixed bed blade on the right side of Figure 2.
This is where the large pieces entering the cutting chamber will be sheared for the first time. In the design, all stress-bearing components related to this large cutting force were designed to be able to cut 22.2 mm cubes of nylon mill stock. Once large pieces have been cut for the first time by the bed blade, they will accumulate on the surface of the granulation screen. The clearance between the tip of the fly knives during rotation and the inside of the screen in 3 mm, which means that any larger granules will get pinched between the screen and the blade and be sheared to a smaller size. Once the granules are smaller than 6 mm in all dimensions, they are pulled through the holes located in the granulation screen and into a collection chamber by a vacuum. Thus, the vacuum is used for the collection of the granules of cut plastic. In order to make the blade arms rotate, as described in Section 2.1, weld-on hubs attached to the shaft were bolted onto the blade arms. For the cutting system fly knife blades were manufactured from O1 tool steel and a Bridgeport was used to manually face fill the stock down to dimension. Once block was dimensioned down an end mill was used to cut slots and pockets needed to attach the bolts. Finally, an angle vise was used to face mill the bevel for the cutting edge all to the specifications with the drawings [63]. After machining the blades were heat-treated using an electric furnace and quenched in oil in order to harden the tool steel following standard protocols. For the granulation screen, a seamless pipe cut to width was used as the starting material, but due to manufacturing methods the pipe had internal stresses. Heat treating the pipe in an electric furnace and then letting it air cool relieved the internal stresses. This step is not required if tools are not available as one could continue to cut the pipe, but stress may not be relieved, and it will spring open. After the stress relief heat treatment, an angle grinder is used to cut a straight line down the length of the pipe and then cut the other side of the pipe to provide equal halves, which are then subsequently drilled as shown in the Figures.

2.3. Material Guidance

The material guidance system is responsible for containing the waste plastic both before and after the cutting operation. In addition to guiding materials, this system also serves as the structure upon which all other subsystems are constructed. The feedstock is guided using a sloped tube as shown in Figure 3.
Overall, the main component used for material guidance is a large steel square tube that not only provides a smooth, enclosed surface for the waste plastic to slide on while it is on its way to be cut, but also a very strong and rigid structure that can be built upon. Attached to this large (8” (203 mm) width) square tube are several other components that support the plastic cutting and power transmission systems. The two large rounded plates attached to the vertical faces of the tube are what hold the bearings from the power transmission system in place. The angle iron on the bottom part of the tube serves two purposes. The larger piece holds the fixed bed blade in place during operation, as well as clamping to the second piece of angle iron shown, which secures the granulation screen in place for cutting. The materials on the top of the tube are all responsible for holding the opposite side of the granulation screen in place and allows the user to disconnect the granulation screen quickly from one side. This system also includes a secondary tube acting as a hopper for funnelling material directly from the user’s hand into the machine as well as a server rack cart that is used to house the main cutting mechanism. However, these components are not shown above for clarity.

2.4. Electrical

The electrical system in the machine serves three purposes—powering the motor, powering the granule extraction vacuum, and monitoring the power consumption of the machine. These functions are accomplished simply since both the vacuum and the motor require no more than a simple on/off control scheme. Both the vacuum and the motor are connected directly to 120VAC mains power and use simple switches to control them. In addition, an emergency-stop switch is included in the circuitry to cut power to the whole machine if necessary. The final accessory included in the electronic circuit for this machine is a multimeter that provides a digital readout with information on the power consumption of the machine. All of the components in the electrical system were designed to operate using less than 15 Amps during steady-state conditions so that the machine could be run off of a standard in-home wall outlet. A circuit diagram for the electrical system is included in Figure 4a.

2.5. Peripheral Parts Assembly

Together, the four systems described in Section 2.1, Section 2.2, Section 2.3 and Section 2.4 work together to achieve the overall objective of the design of the open source waste plastic granulator. Other than getting the material from place to place, all of the actual manipulation of the plastic to transform it from stock material into feedstock occurs due to the cutting and power transmission systems. An overall view of the machine’s core systems is shown in Figure 5.
Figure 5 shows the assembly of the three mechanical design systems, including all of the parts explained earlier as well some 3D printed parts and several parts not shown before. The total system dimensions are width of 0.72 m, depth of 0.55 m and height of 1.47 m. The system has a mass of 125 kg. As can be seen in the above picture the server rack cart that was mentioned in the material guidance system is housing the main systems of the granulator. It holds the machine components so that the major axis of the large square tube is angled to allow plastic pieces to slide into the cutting mechanism. To accomplish this, several standard size ½” (12.7 mm)) steel pipes are attached to the server rack using u-bolts. The pipe in the rear (as shown in Figure 5) is attached directly to the bottom of the steel tube using pipe straps, while the pipe in the front is attached via nylon strapping to the eye-bolts shown on the top of the steel tube in the above figure. This is done to allow the builder of the machine to easily add a vibration-dampening spring at the front attachment point to mitigate any rotational imbalance that may be present in the machine. The hopper consists of the large tube sticking out of the top of the server rack as well as a plate that allows it to attach to the back of the square steel tube/main machine body. This allows users to safely place materials into the machine for cutting. The bend that materials will have to pass through in order to get from the machine’s opening to the cutting mechanism ensures that a user cannot accidentally place their hands/arms inside the machine while it is cutting as well as stops granules from flying out of the machine during operation. To highlight the interaction between all three main mechanical systems a cutaway view showing the assembled granulation chamber in Figure 6.

2.6. Cutting Force Design Analysis

The cutting operation that takes place during the operation of the granulator is unpredictable, so a simulation was run of the cutting forces that occur during the operation of the granulator [63]. These forces are important because they allow for the calculation of the stresses that occur inside the key stress-bearing elements of the design. The method and findings are in the OSF database [63].
The stress levels inside the blade arm as well as the fly knife bolts are well below the acceptable level for steel materials. In order to achieve this, it was determined that the blade arms must be made out of 19 mm × 63.5 mm steel flat stock, and that the bolts must be 16 UNC (9.525 mm) grade 8 hex cap screws. Previous simulations found that a 12.7 mm thick piece of angle iron with side lengths of 76.2 mm would be suitably strong for this piece. In this study, 6.35 mm–20 UNC bolts were selected despite being over engineered because they proved inexpensive for this application. After iterating the simulation to find the optimal size for the bed blade mounting bolts, both locations were considered, and 912.7 mm −12 UNC grade 8 hex cap bolts were chosen. Standard fatigue analysis [64] was performed, and it was found that the grade 9 bolts responsible for attaching the fly knife blades to the blade arms are predicted to fail due to fatigue before infinite life. That being said, the analysis done assumes that a 19 mm nylon block will enter the machine once every time one knife rotates, which, for normal operation, is very unlikely. For normal use, the stresses present will never reach the values used for analysis. However, users planning on using this machine for nylon recycling should replace these bolts every month in order to avoid failure due to fatigue. The maximum torque acting on the cutting rotor during operation is slightly less than 1500 N-m. In order to attach the cutting rotor to the shaft two SK type QD bushings were chosen, since each bushing can support a torque of about 800 N-m. Together, these two bushings can support a maximum torque of 1580 N-m, a torque that should never be exceeded during the normal operation of the machine. In conclusion, the design simulation indicated that the technology as designed would be able to cut a maximum thickness of nylon stock of 19 mm, i.e., a cube measuring 19 mm on each side is the largest piece of plastic stock that should be inserted into the machine.

3. Material and Methods

3.1. Technical Specifications: Power Consumption and Particle Size

The power consumption operating the granulator as measured with an open-source printed circuit board and Arduino Nano attached to the power supply to measure the power output of the while it was processing different materials. During each of the power recording sessions, thermoplastic was inserted at a rate the granulator could handle. This rate is not measured, as it highly depends on the geometry and density of the inserted plastic.
The AC power measurement system is a custom system designed for measuring and recording general AC power consumption data. The device is prototyped as a custom professionally manufactured printed circuit board (PCB). The PCB was then soldered by hand. The system is capable of making four separate AC measurements. Each leg’s measurements are connected to a dedicated Analog Devices ADE7757 energy metering integrated circuit (IC). The IC meets the IEC61036 accuracy requirements for power measurements. The ADE7757 transmits the wattage signal through its CF pin, and is captured by the on-board Arduino Nano. An overall system schematic is shown in Figure 4b.
For analyzing the power consumption of the shredder, both input legs of the 220 VAC power input to the control electronics are monitored. Each leg’s corresponding voltage is measured by direct connection, and current is measured using 100A non-invasive current transformers. The values are operated on by a linear calibration, and then written to a microSD card, with time stamps generated by the on-board real time clock. The size characteristics of the particles for the resultant granulated material were quantified using digital imaging and the open source Fiji/ImageJ using techniques discussed previously [60]. ImageJ works by analyzing a photograph of the particles and raising the contract of the photograph until all particles are clearly recognizable to the program as solid black pieces. From the analysis, a spreadsheet of data is produced with the surface area of each particle. This is then plotted in a histogram to provide a quantifiable understanding of the particle size distribution. Each analysis was repeated three times.

3.2. Noise Reduction

Sound pressure levels (SPL) were measured using a free field array microphone positioned in front of the vacuum inlet of the machine at a distance of approximately 0.3m from the open source waste plastic granulator. The measurements were logged using a National Instruments (Austin, TX, USA) compact DAQ data acquisition system in conjunction with custom LabVIEW software. Multiple positions were considered before finalizing on the position in Figure 7 due to repeatability and high signal-to-noise ratio. All trials were performed using this microphone position Sources of sound in the machine includes the shear cutting mechanism in the granulator and the shop vacuum. Although the microphone location was not in the operator ear position, it was appropriately placed for before/after insertion loss measurements.
Tests were performed to find the sound pressure levels of the open source waste plastic granulator system including the auxiliary devices such as the vacuum pump and the individual contributions as well. It was determined that the vacuum pump was the loudest source with a distinct peak in the 250 Hz one third-octave band. Panel gaps in the enclosure for the granulator provides leakage paths for the sound and hence it was decided to seal these gaps appropriately. The inner lining of the walls was packed with open-celled foam to increase sound absorption and transmission loss, as shown in Figure 8.
Using the initial acoustic measurements, an expansion chamber was designed (Figure 9) that could be attached to the five-gallon bucket shop vacuum, and a 3D model was produced to utilize PVC and a 3D printable components to reduce noise from the operation of the device. As 250Hz was the chosen frequency one third octave band for attenuation, the double tuned expansion chamber design was chosen as it provides good transmission loss around the frequency of interest while having good attenuation around the octave bands as well [65]. However, the muffler aids in higher frequency attenuation and by lining the inner walls of the muffler with fiberglass foam.

4. Results

4.1. Technical Specifications for Particle Size and Energy Use

Figure 10 shows the resultant particles and particle size distribution, where it is clear that the majority of particles are fines with total areas under 10 mm2. These particle sizes are appropriate for the majority of recyclebots as well as direct material extruder–based 3D printers such as the Gigabot X [58,59,60].
This power draw of the open source waste plastic granulator was processed, and its results appear below in a Table 1. The average power varied depending on the type of plastic and would be expected to change based on the type of feedstock (e.g., large solid blocks vs flakes). The time to process a kg of waste plastic ranged between 15 min to 30 min.

4.2. Noise Reduction Results

The noise reduction modifications to the granulator were verified with sound level measurements and are as shown in Figure 11, Figure 12 and Figure 13. Compared to the earlier design, a 4dB (1.5 dBA) overall reduction in sound levels was achieved with attenuation at the 250Hz one third octave band particularly. As the focus of the noise reduction was concentrated toward the vacuum, a 5 dB (3.2 dBA) reduction was achieved here.
The overall levels are approximately at 94 dB (90 dBA) and according to OSHA, four hours of exposure time is the maximum to prevent hearing damage while operating this device. It is therefore recommended to wear hearing protection equipment while operating the device.

5. Discussion

5.1. Technical Specifications for Particle Size, Throughput, and Energy Use

The particle sizes demonstrated in Figure 10 are small enough to use in a wide array of recyclebots (both commercial and homemade) as well as for direct printing via FPF/FGF as demonstrated in references [58,59,60].
The volumes that the device can process are appropriate for small businesses [13], community centers, libraries, maker spaces, and fab labs [59,66] that could potentially become community distributed recycling centers. There are challenges with this approach throughout the world. Although libraries in Finland, for example, routinely offer their patrons free 3D printing services, many countries do not. In addition, the actual recycling process can be challenging due to lack of appropriate information in specific countries. For example, China has a sophisticated recycling symbol system [67] that covers a wide range of waste plastics, and the US groups most of its polymers together in only 1 of 7 categories (7 = “other”) [68]. In order to have low-cost distributed recycling waste plastics need to be appropriately labeled. The open source 3D printer community has already devised a voluntary recycling code based on China’s comprehensive system [68]. To have a more widespread impact and reach a cradle-to-cradle material cycle [69], regulations that demand that manufacturers identify the materials in their products appear necessary [70].
The power draw for the open source waste plastic granulator is relatively mild, drawing as much power as 3-4 conventional incandescent light bulbs. Coupling this low power use to the rapid throughput of the technology results in a relatively low embodied energy of electricity for grinding plastic with this machine. This is close to values that have been reported for commercial devices used in previous studies of distributed recycling using additive manufacturing [20,21].

5.2. Noise Reduction

Sealing the exhaust port of the suction vacuum with the muffler did reduce the noise levels experienced, which make the system more amenable to non-production facility-based applications like mixed-use fab labs. As stated in the results, a 4 dB overall reduction from the granulator and the suction vacuum combined was obtained, and hence the muffler served the intended purpose. However, efforts to control granulator noise were not as successful, and this was possibly due to existing panel gaps in the enclosure. They were not sealed off due to need for ease of access. Future work is needed to explore other methods of sound reduction.

5.3. Future Work

This technology is an open source technology built on prior designs [71] and will continue to evolve in the traditional open source fashion. There are thus several areas of future work to improve on the design of the open source waste plastic granulator. First, the cost of the materials for the device is $1943.11 USD, which limits its accessibility throughout many applications. The breakdown in the cost of the materials is summarized in Figure 14 and detailed in Table 2.
To further drive down costs, additional components should be redesigned to use digital manufacturing technologies, the mass of parts should be minimized to maintain the necessary mechanical integrity (which is most easily done in the reduction of structural steel that makes up nearly a third of the cost), and the volume footprint of the device should be reduced. These costs were for retail-purchased materials and would be expected to drop significantly if an open hardware company built the devices at even modest scale. In addition, there are several areas of technical work that may improve the results of the technology for different polymers including detailed studies on the size, morphology, and distribution for different types of polymers, as well as their form (e.g., 3D printed waste, food containers, or industry bulk waste). In addition, the impacts of the heat generated in the machine can be quantified to determine if it has any effect on the material quality.

6. Conclusions

This study successfully demonstrates the designs, build, and testing of an open source waste plastic granulator for its ability to convert post-consumer waste, 3D printed products, and 3D printer waste into polymer feedstock for recyclebots of fused particle/granule printers. The device can be built from open source plans using materials that cost less than $2000 USD. The device has a power consumption (380 to 404W for PET and PLA, the most common post-consumer plastic waste and most popular 3D printer plastic, respectively). With this device, granules can be produced with a particle size distribution consistent with distributed recycling and manufacturing using open source recyclebots and 3D printers. Simple retrofits for the open source waste plastic granulator are shown to reduce sound levels during operation by 4dB and 5dB for the vacuum. It can be concluded that the open source waste plastic granulator is an appropriate technology for community, library, maker space, fab lab, or small business–based distributed recycling.

Author Contributions

Conceptualization, J.M.P.; Data curation, A.R., S.S., W.N., P.G., J.F., S.O. and T.K.M.; Formal analysis, A.R., W.N., P.G., J.F., S.O., T.K.M., A.R.B. and J.M.P.; Funding acquisition, J.M.P.; Investigation, A.R., S.S., W.N., P.G., J.F., S.O. and T.K.M.; Methodology, A.R., W.N., P.G., S.O. and T.K.M.; Resources, A.R.B. and J.M.P.; Supervision, J.M.P.; Validation, A.R., S.S., W.N., P.G., S.O. and T.K.M.; Visualization, A.R., W.N., J.F., and P.G.; Writing—original draft, A.R. and J.M.P.; Writing—review & editing, A.R., S.S., W.N., P.G., S.O., J.F., T.K.M., A.R.B. and J.M.P.

Funding

This research was funded by the Witte Endowment.

Acknowledgments

The authors would like to acknowledge technical support from Paul Fraley and Dan Seguin.

Conflicts of Interest

The authors declare no conflict of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.

References

  1. Sells, E.; Bailard, S.; Smith, Z.; Bowyer, A.; Olliver, V. RepRap: The Replicating Rapid Prototyper-Maximizing Customizability by Breeding the Means of Production. In Proceedings of the World Conference on Mass Customization and Personalization, Cambridge, MA, USA, 7–10 October 2007. [Google Scholar]
  2. Jones, R.; Haufe, P.; Sells, E.; Iravani, P.; Olliver, V.; Palmer, C.; Bowyer, A. RepRap-the Replicating Rapid Prototyper. Robotica 2011, 29, 177–191. [Google Scholar] [CrossRef]
  3. Bowyer, A. 3D Printing and Humanity’s First Imperfect Replicator. 3d Print. Addit. Manuf. 2014, 1, 4–5. [Google Scholar] [CrossRef]
  4. Rundle, G. A Revolution in the Making: 3D Printing. Robots and the Future; Affirm Press: South Melbourne, Australia, 2014. [Google Scholar]
  5. Gwamuri, J.; Wittbrodt, B.; Anzalone, N.; Pearce, J. Reversing the Trend of Large Scale and Centralization in Manufacturing: The Case of Distributed Manufacturing of Customizable 3D-Printable Self-Adjustable Glasses. Chall. Sustain. 2014, 2, 30–40. [Google Scholar] [CrossRef]
  6. Steenhuis, H.J.; Pretorius, L. Consumer additive manufacturing or 3D printing adoption: An exploratory study. J. Manuf. Technol. Manag. 2016, 27, 990–1012. [Google Scholar] [CrossRef]
  7. Wittbrodt, B.; Laureto, J.; Tymrak, B.; Pearce, J. Distributed Manufacturing with 3D Printing: A Case Study of Recreational Vehicle Solar Photovoltaic Mounting Systems. J. Frugal Innov. 2015, 1, 1–7. [Google Scholar] [CrossRef]
  8. Woern, A.L.; Pearce, J.M. Distributed Manufacturing of Flexible Products: Technical Feasibility and Economic Viability. Technologies 2017, 5, 71. [Google Scholar] [CrossRef]
  9. Wittbrodt, B.T.; Glover, A.G.; Laureto, J.; Anzalone, G.C.; Oppliger, D.; Irwin, J.L.; Pearce, J.M. Life-cycle economic analysis of distributed manufacturing with open-source 3D printers. Mechatronics 2013, 23, 713–726. [Google Scholar] [CrossRef]
  10. Petersen, E.E.; Kidd, R.W.; Pearce, J.M. Impact of DIY Home Manufacturing with 3D Printing on the Toy and Game Market. Technologies 2017, 5, 45. [Google Scholar] [CrossRef]
  11. Petersen, E.E.; Pearce, J. Emergence of Home Manufacturing in the Developed World: Return on Investment for Open-Source 3D Printers. Technologies 2017, 5, 7. [Google Scholar] [CrossRef]
  12. Anderson, P.; Sherman, C.A. A discussion of new business models for 3D printing. Int. J. Technol. Mark. 2007, 2, 280–294. [Google Scholar] [CrossRef]
  13. Laplume, A.; Anzalone, G.; Pearce, J. Open-source, self-replicating 3D printer factory for small-business manufacturing. Int. J. Adv. Manuf. Technol. 2015, 85, 633–642. [Google Scholar] [CrossRef]
  14. Laplume, A.; Petersen, B.; Pearce, J. Global value chains from a 3D printing perspective. J. Int. Bus. Stud. 2016, 47, 595–609. [Google Scholar] [CrossRef]
  15. Gallup, N.; Bow, J.K.; Pearce, J.M. Economic Potential for Distributed Manufacturing of Adaptive Aids for Arthritis Patients in the U.S. Geriatrics 2018, 3, 89. [Google Scholar] [CrossRef] [PubMed]
  16. Pearce, J.M. Return on investment for open source scientific hardware development. Sci. Public Policy 2016, 43, 192–195. [Google Scholar] [CrossRef]
  17. Pearce, J. Quantifying the Value of Open Source Hardware Development. Mod. Econ. 2015, 6, 1–11. [Google Scholar] [CrossRef]
  18. Wohlers Associates. Wohlers Report 2018: 3D Printing and Additive Manufacturing State of the Industry; Annual Worldwide Progress Report; Associates Inc: Fort Collins, CO, USA, 2018. [Google Scholar]
  19. Baechler, C.; DeVuono, M.; Pearce, J.M. Distributed recycling of waste polymer into RepRap feedstock. Rapid Prototyp. J. 2013, 19, 118–125. [Google Scholar] [CrossRef]
  20. Kreiger, M.; Anzalone, G.C.; Mulder, M.L.; Glover, A.; Pearce, J.M. Distributed recycling of post-consumer plastic waste in rural areas. MRS Online Proc. Libr. Arch. 2013, 1492, 91–96. [Google Scholar] [CrossRef]
  21. Kreiger, M.A.; Mulder, M.L.; Glover, A.G.; Pearce, J.M. Life cycle analysis of distributed recycling of post-consumer high density polyethylene for 3D printing filament. J. Clean. Prod. 2014, 70, 90–96. [Google Scholar] [CrossRef]
  22. Zhong, S.; Rakhe, P.; Pearce, J.M. Energy Payback Time of a Solar Photovoltaic Powered Waste Plastic Recyclebot System. Recycling 2017, 2, 10. [Google Scholar] [CrossRef]
  23. Unruh, G. Circular Economy, 3D Printing, and the Biosphere Rules. Calif. Manag. Rev. 2018, 60, 95–111. [Google Scholar] [CrossRef]
  24. Zhong, S.; Pearce, J.M. Tightening the loop on the circular economy: Coupled distributed recycling and manufacturing with recyclebot and RepRap 3D printing. Resour. Conserv. Recycl. 2018, 128, 48–58. [Google Scholar] [CrossRef]
  25. Shonnard, D.; Tipaldo, E.; Thompson, V.; Pearce, J.; Caneba, G.; Handler, R. Systems Analysis for PET and Olefin Polymers in a Circular Economy. Procedia CIRP 2019, 80, 602–606. [Google Scholar] [CrossRef]
  26. Garmulewicz, A.; Holweg, M.; Veldhuis, H.; Yang, A. Disruptive Technology as an Enabler of the Circular Economy: What Potential Does 3D Printing Hold? Calif. Manag. Rev. 2018, 60, 112–132. [Google Scholar] [CrossRef]
  27. Recyclebot. Appropedia. Available online: http://www.appropedia.org/Recyclebot (accessed on 8 February 2019).
  28. Woern, A.L.; McCaslin, J.R.; Pringle, A.M.; Pearce, J.M. RepRapable Recyclebot: Open source 3D printable extruder for converting plastic to 3D printing filament. HardwareX 2018, 4, e00026. [Google Scholar] [CrossRef]
  29. Cruz Sanchez, F.; Lanza, S.; Boudaoud, H.; Hoppe, S.; Camargo, M. Polymer Recycling and Additive Manufacturing in an Open Source context: Optimization of processes and methods. In Proceedings of the 2015 Annual International Solid Freeform Fabrication Symposium-An Additive Manufacturing Conference, Austin, TX, USA, 10–12 August 2015; pp. 10–12. [Google Scholar]
  30. Cruz Sanchez, F.A.; Boudaoud, H.; Hoppe, S.; Camargo, M. Polymer recycling in an open-source additive manufacturing context: Mechanical issues. Addit. Manuf. 2017, 17, 87–105. [Google Scholar] [CrossRef]
  31. Anderson, I. Mechanical Properties of Specimens 3D Printed with Virgin and Recycled Polylactic Acid. 3D Print. Addit. Manuf. 2017, 4, 110–115. [Google Scholar] [CrossRef]
  32. Pakkanen, J.; Manfredi, D.; Minetola, P.; Iuliano, L. About the Use of Recycled or Biodegradable Filaments for Sustainability of 3D Printing. In Sustainable Design and Manufacturing, Smart Innovation, Systems and Technologies; Springer: Cham, Switzerland, 2017; pp. 776–785. [Google Scholar]
  33. Mohammed, M.I.; Mohan, M.; Das, A.; Johnson, M.D.; Badwal, P.S.; McLean, D.; Gibson, I. A low carbon footprint approach to the reconstitution of plastics into 3D-printer filament for enhanced waste reduction. Knowl. E. 2017, 2, 234–241. [Google Scholar] [CrossRef] [Green Version]
  34. Mohammed, M.I.; Das, A.; Gomez-Kervin, E.; Wilson, D.; Gibson, I. EcoPrinting: Investigating the use of 100% recycled Acrylonitrile Butadiene Styrene (ABS) for Additive Manufacturing. Solid Freeform Fabrication 2017. In Proceedings of the 28th Annual International Solid Freeform Fabrication Symposium, Austin, TX, USA, 7–9 August 2017. [Google Scholar]
  35. Mohammed, M.I.; Wilson, D.; Gomez-Kervin, E.; Vidler, C.; Rosson, L.; Long, J. The Recycling of E-Waste ABS Plastics by Melt Extrusion and 3D Printing Using Solar Powered Devices as a Transformative Tool for Humanitarian Aid. 2018. Available online: Sffsymposium. engr. utexas. edu/sites/default/files/2018/007% 20TheRecyclingofEWasteABSPlasticsbyMeltExtr. pdf (accessed on 19 April 2019).
  36. Mohammed, M.; Wilson, D.; Gomez-Kervin, E.; Tang, B.; Wang, J. Investigation of closed loop manufacturing with Acrylonitrile Butadiene Styrene (ABS) over multiple generations using Additive Manufacturing. ACS Sustain. Chem. Eng. 2019, 7, 13955–13969. [Google Scholar] [CrossRef]
  37. Chong, S.; Pan, G.T.; Khalid, M.; Yang, T.C.K.; Hung, S.T.; Huang, C.M. Physical Characterization and Pre-assessment of Recycled High-Density Polyethylene as 3D Printing Material. J. Polym. Environ. 2017, 25, 136–145. [Google Scholar] [CrossRef]
  38. Pepi, M.; Zander, N.; Gillan, M. Towards Expeditionary Battlefield Manufacturing Using Recycled, Reclaimed, and Scrap Materials. JOM 2018, 70, 2359–2364. [Google Scholar] [CrossRef]
  39. Zander, N.E.; Gillan, M.; Lambeth, R.H. Recycled polyethylene terephthalate as a new FFF feedstock material. Addit. Manuf. 2018, 21, 174–182. [Google Scholar] [CrossRef]
  40. Hart, K.R.; Frketic, J.B.; Brown, J.R. Recycling meal-ready-to-eat (MRE) pouches into polymer filament for material extrusion additive manufacturing. Addit. Manuf. 2018, 21, 536–543. [Google Scholar] [CrossRef]
  41. Tian, X.; Liu, T.; Wang, Q.; Dilmurat, A.; Li, D.; Ziegmann, G. Recycling and remanufacturing of 3D printed continuous carbon fiber reinforced PLA composites. J. Clean. Prod. 2017, 142, 1609–1618. [Google Scholar] [CrossRef]
  42. Pringle, A.M.; Rudnicki, M.; Pearce, J. Wood Furniture Waste-Based Recycled 3D Printing Filament. For. Prod. J. 2018, 68, 86–95. [Google Scholar] [CrossRef]
  43. Zander, N.E. Recycled Polymer Feedstocks for Material Extrusion Additive Manufacturing. In Polymer-Based Additive Manufacturing: Recent Developments; ACS Symposium Series; American Chemical Society: Washington, DC, USA, 2019; Volume 1315, pp. 37–51. ISBN 978-0-8412-3426-0. [Google Scholar]
  44. Oblak, P.; Gonzalez-Gutierrez, J.; Zupančič, B.; Aulova, A.; Emri, I. Processability and mechanical properties of extensively recycled high density polyethylene. Polym. Degrad. Stab. 2015, 114, 133–145. [Google Scholar] [CrossRef]
  45. Hyung Lee, J.; Sub Lim, K.; Gyu Hahm, W.; Hun Kim, S. Properties of recycled and virgin poly(ethylene terephthalate) blend fibers. Appl. Polym. Sci. 2012, 128, 2. [Google Scholar]
  46. Bai, X.; Isaac, D.H.; Smith, K. Reprocessing acrylonitrile–butadiene–styrene plastics: Structure–property relationships. Polym. Eng. Sci. 2007, 47, 120–130. [Google Scholar] [CrossRef]
  47. Sasse, F.; Emig, G. Chemical Recycling of Polymer Materials. Chem. Eng. Technol. 1998, 21, 777–789. [Google Scholar] [CrossRef]
  48. Pavlo, S.; Fabio, C.; Hakim, B.; Mauricio, C. 3D-Printing Based Distributed Plastic Recycling: A Conceptual Model for Closed-Loop Supply Chain Design. In Proceedings of the 2018 IEEE International Conference on Engineering, Technology and Innovation (ICE/ITMC), Stuttgart, Germany, 17–20 June 2018; pp. 1–8. [Google Scholar]
  49. Volpato, N.; Kretschek, D.; Foggiatto, J.A.; da Silva Cruz, C.G. Experimental analysis of an extrusion system for additive manufacturing based on polymer pellets. Int. J. Adv. Manuf. Technol. 2015, 81, 1519–1531. [Google Scholar] [CrossRef]
  50. Beaudoin, A. JMS-1704: Multihead 3D Printer. Ph.D. Thesis, Worcester Polytechnic Institute Worcester, Worcester, MA, USA, 2016. [Google Scholar]
  51. Whyman, S.; Arif, K.M.; Potgieter, J. Design and development of an extrusion system for 3D printing biopolymer pellets. Int. J. Adv. Manuf. Technol. 2018, 96, 3417–3428. [Google Scholar] [CrossRef]
  52. Giberti, H.; Sbaglia, L.; Silvestri, M. Mechatronic Design for an Extrusion-Based Additive Manufacturing Machine. Machines 2017, 5, 29. [Google Scholar] [CrossRef]
  53. Liu, X.; Chi, B.; Jiao, Z.; Tan, J.; Liu, F.; Yang, W. A large-scale double-stage-screw 3D printer for fused deposition of plastic pellets. J. Appl. Polym. Sci. 2017, 134, 45147. [Google Scholar] [CrossRef]
  54. Khondoker, M.A.H.; Sameoto, D. Direct coupling of fixed screw extruders using flexible heated hoses for FDM printing of extremely soft thermoplastic elastomers. Prog. Addit. Manuf. 2019, 4, 197–209. [Google Scholar] [CrossRef]
  55. Horne, R. Reprap Development and Further Adventures in DIY 3D Printing: No More Filament? -Quest for a Universal Pellet Extruder for 3D Printing. Reprap Development and Further Adventures in DIY 3D Printing 2014. Available online: https://richrap.blogspot.com/2014/12/no-more-filament-quest-for-universal.html (accessed on 9 August 2018).
  56. Universal Pellet Extruder. Available online: http://upe3d.blogspot.com/ (accessed on 9 August 2018).
  57. Braanker, G.B.; Duwel, J.E.P.; Flohil, J.J.; Tokaya, G.E. Developing a Plastics Recycling Add-on for the RepRap 3D-Printer. Available online: https://reprapdelft.wordpress.com (accessed on 9 August 2018).
  58. Woern, A.; Byard, D.; Oakley, R.; Fiedler, M.; Snabes, S.; Pearce, J.; Woern, A.L.; Byard, D.J.; Oakley, R.B.; Fiedler, M.J.; et al. Fused Particle Fabrication 3D Printing: Recycled Materials’ Optimization and Mechanical Properties. Materials 2018, 11, 1413. [Google Scholar] [CrossRef] [PubMed]
  59. Byard, D.J.; Woern, A.L.; Oakley, R.B.; Fiedler, M.J.; Snabes, S.L.; Pearce, J.M. Green Fab Lab Applications of Large-Area Waste Polymer-based Additive Manufacturing. Addit. Manuf. 2019, 27, 515–525. [Google Scholar] [CrossRef]
  60. Reich, M.J.; Woern, A.L.; Tanikella, N.G.; Pearce, J.M. Mechanical Properties and Applications of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing. Materials 2019, 12, 1642. [Google Scholar] [CrossRef]
  61. Gibb, A. Building Open Source Hardware: DIY Manufacturing for Hackers and Makers; Pearson Education: London, UK, 2014; ISBN 978-0-321-90604-5. [Google Scholar]
  62. Oberloier, S.; Pearce, J.M. General Design Procedure for Free and Open-Source Hardware for Scientific Equipment. Designs 2017, 2, 2. [Google Scholar] [CrossRef]
  63. Open Source Granulator. Open Science Framework. 2018. Available online: https://osf.io/a2tk9/ (accessed on 9 August 2018).
  64. Juvinall, R.C.; Marshek, K.M. Fundamentals of Machine Component Design; John Wiley & Sons: Hoboken, NJ, USA, 1991. [Google Scholar]
  65. Vér, I.L.; Beranek, L.L. Passive Silencers. In Noise and Vibration Control Engineering: Principles and Applications, 2nd ed.; John Wiley & Sons, Inc.: Hoboken, NJ, USA, 2005; ISBN 9780470172568. [Google Scholar]
  66. Stacey, M. The FAB LAB network: A global platform for digital invention, education and entrepreneurship. Innov. Technol. Gov. Glob. 2014, 9, 221–238. [Google Scholar] [CrossRef]
  67. Standardization Administration of the People’s Republic of China (SAC). GB16288, 2008. Marking of Plastics Products; Chinese Standard Publishing House: Beijing, China, 2008. [Google Scholar]
  68. Hunt, E.J.; Zhang, C.; Anzalone, N.; Pearce, J.M. Polymer recycling codes for distributed manufacturing with 3D printers. Resour. Conserv. Recycl. 2015, 97, 24–30. [Google Scholar] [CrossRef]
  69. McDonough, W.; Braungart, M. Cradle to Cradle: Remaking the Way We Make Things; Farrar, Straus and Giroux: New York, NY, USA, 2010; ISBN 978-1-4299-7384-7. [Google Scholar]
  70. Pearce, J.M. Expanding the Consumer Bill of Rights for material ingredients. Mater. Today 2018, 21, 197–198. [Google Scholar] [CrossRef] [Green Version]
  71. OSHE. Granulator MKII, Open Science Framework. Available online: https://osf.io/auswp/ (accessed on 10 July 2018).
Figure 1. Power transmission system design of the open source waste plastic granulator.
Figure 1. Power transmission system design of the open source waste plastic granulator.
Technologies 07 00074 g001
Figure 2. Plastic cutting system design of the open source waste plastic granulator. There is about 2mm gap between the knives and the screen.
Figure 2. Plastic cutting system design of the open source waste plastic granulator. There is about 2mm gap between the knives and the screen.
Technologies 07 00074 g002
Figure 3. Material guidance system (cut section and completed) for the open source waste plastic granulator.
Figure 3. Material guidance system (cut section and completed) for the open source waste plastic granulator.
Technologies 07 00074 g003
Figure 4. (a) Circuit diagram for electrical control system of the open source waste plastic granulator and (b) circuit diagrams.
Figure 4. (a) Circuit diagram for electrical control system of the open source waste plastic granulator and (b) circuit diagrams.
Technologies 07 00074 g004
Figure 5. Overall design setup of the open source waste plastic granulator with primary parts labeled with green arrows. Red arrows indicate the path of material flow.
Figure 5. Overall design setup of the open source waste plastic granulator with primary parts labeled with green arrows. Red arrows indicate the path of material flow.
Technologies 07 00074 g005
Figure 6. Cutaway of mechanical systems in the open source waste plastic granulator.
Figure 6. Cutaway of mechanical systems in the open source waste plastic granulator.
Technologies 07 00074 g006
Figure 7. Sound measurement test setup depicting the microphone in one of the test locations.
Figure 7. Sound measurement test setup depicting the microphone in one of the test locations.
Technologies 07 00074 g007
Figure 8. Granulator panel gaps filled with sound proofing material.
Figure 8. Granulator panel gaps filled with sound proofing material.
Technologies 07 00074 g008
Figure 9. Comparison between computer aided design (CAD) of chamber and finished expansion chamber.
Figure 9. Comparison between computer aided design (CAD) of chamber and finished expansion chamber.
Technologies 07 00074 g009
Figure 10. Resultant particle size distribution in mm2 after shredding in the open source granulator. Inset: picture of shredded PLA from failed 3D prints.
Figure 10. Resultant particle size distribution in mm2 after shredding in the open source granulator. Inset: picture of shredded PLA from failed 3D prints.
Technologies 07 00074 g010
Figure 11. Results of the sound reduction redesign showing a bar plot of 1/3 octave noise measurements.
Figure 11. Results of the sound reduction redesign showing a bar plot of 1/3 octave noise measurements.
Technologies 07 00074 g011
Figure 12. Results of the sound reduction redesign showing a bar plot of 1/3 octave noise measurements with dBA (A-weighted decibels) weighting.
Figure 12. Results of the sound reduction redesign showing a bar plot of 1/3 octave noise measurements with dBA (A-weighted decibels) weighting.
Technologies 07 00074 g012
Figure 13. Results of the sound reduction redesign on the vacuum showing a bar plot of 1/3 octave noise measurements with dBA weighting.
Figure 13. Results of the sound reduction redesign on the vacuum showing a bar plot of 1/3 octave noise measurements with dBA weighting.
Technologies 07 00074 g013
Figure 14. Cost breakdown of the bill of materials for the open source granulator.
Figure 14. Cost breakdown of the bill of materials for the open source granulator.
Technologies 07 00074 g014
Table 1. Power consumption details.
Table 1. Power consumption details.
PLA (Polylactic Acid) Infill and Failed PrintsPET (Polyethylene Terephthalate) Post-Consumer Water BottlesABS (Acrylonitrile Butadiene Styrene) Injection Molded
Average power403.6 (+/−50 W) *383.9 W460.0 W
Average time16 min15 min28 min
* Note: The PLA power depended in part on the nature of the 3D printed waste with the more solid components taking longer.
Table 2. Costs of all the components and numbers and sub-systems in the bill of materials for the open source granulator.
Table 2. Costs of all the components and numbers and sub-systems in the bill of materials for the open source granulator.
CategoryPieceFunctionPriceQuantityComponent Total CostGroup Total Cost
Steel/Structural8" Square Steel Tube 18" LengthMain Body85.18185.18$ 594.88
1/2" 3" × 3" Angle Iron 8" LengthBed Blade Mount10.56110.56
3/4" × 2-1/2" Flat Stock 12" LengthFlyknife Arms10.43110.43
8" OD 7.5" ID Steel Tube 8" Length Granulation Screen55.2155.2
1/4" Steel Plate 8" × 10"Bearing Plates17.66235.32
1/4" × 3/4" Steel Flat Bar 8" LengthGranulation Screen Back Spacer3.8913.89
3/4" × 3/8" × 1/8" Steel Channel 6" LengthHinge Mount Plate Connectors4.6829.36
2" × 1-1/2" × 1/4" Steel Angle 8" LengthGranulation Screen Clamp6.3216.32
1/2" × 1" 6061 Aluminum Flat Bar 3" LengthGranulation Screen Front Shims3.9913.99
Norco R4-15U Server RackCart/Body Structure1821182
1/2" Steel Pipe 24" LengthServer Rack Mounting Interface5.58211.16
Polypropylene hanging strapSupport front of granulator7.25214.5
8" × 12" × 1/4" Steel FlatMotor Mount Plate12.95112.95
1 3/4" × 1/4" × 8" Steel FlatToggle Pull Connection Plate2.2412.24
8" × 8" × 1/2" Plywood SheetHopper Closure20120
6" PVC ElbowHopper Part20.42120.42
6" PVC FlangeHopper Part19.36119.36
6" PVC SectionHopper Part17117
Various 3D Printed PartsVarious Things75175
ElectricalIndoor Steel Enclosure with KnockoutsElectronics Enclosure12.53112.53$ 218.96
Screw-Down Cord Grip for Building CableConduit Holder1.8835.64
DC 6.5-100V 0-100A LCD DisplayEnergy Usage Display20120
Heat Shrink TubingCable Management Stuff20120
12-3 AC Power CablePower Cable64.77164.77
SPST Switch rated for >15AMachine On/Off Switch4.1828.36
Limit Switch Z-15ESafety Switch17.08117.08
Emergency Stop SwitchEmergency Power Interruption44.93144.93
5 gal 1.75-Peak HP Wet Dry VacGranule Retrieval Vacuum21.97121.97
15 amp circuit breakerreplace failing fuse3.6813.68
Power Transmission1.5HP motor iron horseMotor1651165$ 895.40
Sliding mountAdjustable Motor Mounting21.621
8.95" OD Double V-Belt PulleyShaft Pulley52.36152.36
3.75" OD Double V-Belt PulleyMotor Pulley27.13127.13
V-beltsTo transmit power from motor to shaft13.38226.76
Carbon Steel 40mm Diameter Keyed ShaftRotor Shaft77.72177.72
SK Style QD Bushing 40mm BoreRotor Shaft Bushing (Blade Arms & Pulley)353105
SH Style QD Bushing 5/8" BoreMotor Pulley Bushing16.73116.73
SK Style Weld-on Bushing-Bore HubBlade Arm Connector86.992173.98
40mm Cast Flange BearingsRotor Shaft Bearings50.362100.72
BladesBlades503150
HardwareM16 Locknuts (10 Pack)Mount Bearing to Plates13.15113.15$ 227.58
M16 × 45 Hex Cap Screws (5 Pack)Mount Bearing to Plates11.35111.35
1/4" - 20 × 3/4" Hex Cap Screw Grade 8Mount Channel Stock to Main Body Tube0.1740.68
1/4" - 20 × 4/3" Flat Head Torx Drive Machine ScrewsMounting Shims to Bed Blade Angle Iron1.9947.96
5/16" - 18 × 2" Hex Cap Screw Grade 8Cutting Rotor Hub Bolts0.452
5/16" - 18 × 2 1/2" Full ThreadHex Cap Screw Grade 8Cutting Rotor Hub Bolts0.532
5/16" - 18 × 1 3/8" Hex Cap Screw Grade 9Cutting Rotor Hub Bolts0.952
3/8" - 16 × 7/8" Hex Cap Screw Grade 8Mount Pull Action Toggle Clamp0.3161.86
3/8" - 16 × 5/8" Hex Cap Screw Grade 8Various Mounting Stuff0.3123.6
3/8" - 16 × 1" Hex Cap Screw Grade 8Motor Plate Mounting0.3220.64
3/8" - 16 × 1 5/8" Hex Cap Screw Grade 8Granulation Screen Clamp Downs1.2845.12
3/8*" - 16 Locknut Grade 8Various Mounting Stuff0.2261.32
3/8" Nylon Washers (Pack of 25)Standoffs for Pull Action Toggle Clamp2.2512.25
1/2" -- 13 × 1-1/2" Hex Cap Screws Grade 9 Extreme Strength (Pack of 5)Flyknife Blade Mounting8.7718.77
1/2" - 20 × 7/8" Hex Cap Screws Grade 8Mounting Bed Blade Angle Iron to Square Tube Housing0.9543.8
1/2" - 20 × 1 3/4" Hex Cap Screws Grade 8Bed Blade Mounting1.1933.57
1/2" - 20 Locknut Grade 8Bed Blade Mounting1.1433.42
1/4" - 20 × 3/4" Socket ScrewGranulation Screen Hardware0.1740.68
1/4" - 20 × 7/8" Socket ScrewGranulation Screen Hardware0.1840.72
10-24 × 3/8" Hex Cap Screw Grade 8 (25 Pack)Hardware Mounting to Main Body Tube11.5111.5
1/2" Pipe Strap ClampFrame Hardware1.4322.86
Adjustable Motor-Mounting BaseMotor Mount21.62121.62
Pull Action Toggle ClampGranulation Screen Connection26.87126.87
1/2" × 20 Threaded Eye BoltsFront Square Tube Webbing Connections3.0126.02
1" Black Oxide U-BoltsServer Rack Connection Hardware0.7843.12
Surface Mount Cabinet Hinge (1 pair)Hopper Cover Hinges9.1219.12
1/4" Spacers, 1/4" HeightStandoffs for Channel Stock Mounting Hardware0.563
Draw LatchesClosing Mechanism for Hopper Plate6.77213.54
Various Wood ScrewsWood Screws for Attaching Draw Latches and Hinges to Plywood Hopper515
Various Nuts/BoltsHardware for Attaching PVC Flange to Plywood Hopper Cover & For Attaching Draw Latch to Square Tube Housing10110
Bronze Flange BearingDrill Guide for Granulation Screen3.4313.43
Threadlocker—BlueSecuring Bolts20.38120.38
Key StockQD Hub Securing5.2415.24
40mm Carbide Hole Cutter (2 pack)Cutting Holes in Blade Arms & Side Plates16.99116.99
Sound ReductionFiberglass Utility Roll, 16 × 3/4 × 48-In, Frost KingNoise attenuation6.2916.29$ 6.29
$ 1943.11

Share and Cite

MDPI and ACS Style

Ravindran, A.; Scsavnicki, S.; Nelson, W.; Gorecki, P.; Franz, J.; Oberloier, S.; Meyer, T.K.; Barnard, A.R.; Pearce, J.M. Open Source Waste Plastic Granulator. Technologies 2019, 7, 74. https://0-doi-org.brum.beds.ac.uk/10.3390/technologies7040074

AMA Style

Ravindran A, Scsavnicki S, Nelson W, Gorecki P, Franz J, Oberloier S, Meyer TK, Barnard AR, Pearce JM. Open Source Waste Plastic Granulator. Technologies. 2019; 7(4):74. https://0-doi-org.brum.beds.ac.uk/10.3390/technologies7040074

Chicago/Turabian Style

Ravindran, Arvind, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew R. Barnard, and Joshua M. Pearce. 2019. "Open Source Waste Plastic Granulator" Technologies 7, no. 4: 74. https://0-doi-org.brum.beds.ac.uk/10.3390/technologies7040074

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop