Next Article in Journal
Surface-Response Analysis for the Optimization of a Carbon Dioxide Absorption Process Using [hmim][Tf2N]
Next Article in Special Issue
MILP Formulation for Solving and Initializing MINLP Problems Applied to Retrofit and Synthesis of Hydrogen Networks
Previous Article in Journal
Preliminary Insights into Electro-Sensitive Ecolubricants: A Comparative Analysis Based on Nanocelluloses and Nanosilicates in Castor Oil
Previous Article in Special Issue
Residue Char Derived from Microwave-Assisted Pyrolysis of Sludge as Adsorbent for the Removal of Methylene Blue from Aqueous Solutions
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Communication

Highly-Efficient Caffeine Recovery from Green Coffee Beans under Ultrasound-Assisted SC–CO2 Extraction

Dipartimento di Scienza e Tecnologia del Farmaco, University of Turin, Via P. Giuria 9, 10125 Turin, Italy
*
Author to whom correspondence should be addressed.
Submission received: 2 August 2020 / Revised: 12 August 2020 / Accepted: 19 August 2020 / Published: 1 September 2020
(This article belongs to the Special Issue Redesign Processes in the Age of the Fourth Industrial Revolution)

Abstract

:
Natural caffeine from decaffeination processes is widely used by pharmaceutical, cosmetic and soft-drink industries. Supercritical CO2 extraction (SFE–CO2) is extensively exploited industrially, and one of its most representative applications is the decaffeination process, which is a greener alternative to the use of organic solvents. Despite its advantages, extraction kinetics are rather slow near the CO2 critical point, meaning that improvements are highly sought after. The effect exerted by a combination of SFE–CO2 and ultrasound (US–SFE–CO2) has been investigated in this preliminary study, with the aim of improving mass transfer and selectivity in the extraction of caffeine from green coffee beans. This hybrid technology can considerably enhance the extraction efficiency and cut down process time. Further studies are in progress to demonstrate the complete decaffeination of green coffee beans of different types and origins.

Graphical Abstract

1. Introduction

Caffeine is a xanthine alkaloid widely used in beverages (soft or energy drinks), as well as in pharmaceutical and cosmetic preparations [1]. The global caffeine market was valued at US$ 231.1 million in 2018 and is expected to reach US$ 349.2 million by 2027 expanding at a CAGR (Compound Annual Growth Rate) of 4.7% during the forecast from 2019 to 2027 [2]. This rising demand boosts the global caffeine market. Besides production via chemical synthesis, there is an urgent need to increase caffeine production via isolation from natural sources, the principle of which is coffee beans [3,4]. The decaffeination of green coffee beans commonly involves several steps, such as steaming, extraction, drying and caffeine recovery [4,5,6]. Growing concerns as to the use of organic solvents has stimulated the development of greener techniques for more sustainable and efficient caffeine extraction. Of the alternative green processes available, supercritical CO2 extraction (SFE–CO2) can be considered the technique of choice for decaffeination and the recovery of high-value lipophilic compounds from natural matrices [7,8]. A molecular dynamics simulation study demonstrated that, unlike extraction in water, SFE–CO2 does not favour the aggregation of the caffeine obtained, thus facilitating subsequent purification steps [9]. The aim of extracting 97% caffeine from both Arabica and Robusta green coffee beans has been achieved by this technology in 11.5 h and 22 h, respectively, at 90 °C and 247 bar [10]. The efficiency of SFE–CO2 can be further improved by the addition of a co-solvent, such as ethanol, in order to enhance the polarity of the system [11]. SFE is generally characterised by slow kinetics, meaning that mass-transfer intensification would be a welcome means to improve diffusion. Ultrasound-assisted extraction (UAE) is extremely beneficial, in this sense, thanks to the enhanced mass transfer that occurs under acoustic cavitation [12,13]. Farouk & Hasan [14] have carried out a study using a high-order numerical scheme, and the data seem to confirm that the kinetics of the SFE process are significantly accelerated by cavitational effects. Higher extraction yields and shorter extraction times can therefore be achieved when SFE–CO2 processes are assisted by ultrasound (US) [15]. Currently, US–SFE–CO2 extractors are mainly available only on lab and pilot scales, and there is a distinct lack of industrial-scale data [16]. Extensive analysis on the synergistic effect of US with SFE–CO2 have been summarized by Dassoff & Li, [17], namely micro- and macro-mixing, mechanical effects on the cell wall that enhance both convective mass transfer as well as internal diffusivity. Under CO2 pressure the oxidative degradations that may occur under sonication are negligible. A pilot-scale process using an innovative US–SFE–CO2 system has been proposed for oil extraction from different vegetal matrices [18].
The aim of this work is to evaluate the effectiveness of ultrasound assistance in the extraction of caffeine from green coffee beans using SFE–CO2. This preliminary investigation should provide useful data to facilitate a drastic reduction in extraction time. The scalability of this hybrid technology for decaffeination will require further engineering studies. In this work, an SFE unit, equipped with a tightly fixed sonotrode with an immersion horn, has been used under sonication and silent conditions. Extract analysis was carried out using ultra-performance liquid chromatography–tandem mass spectrometry (UPLC-MS-MS).

2. Materials and Methods

2.1. Coffee Sample and Chemicals

Green coffee beans (Arabica, Brazil), that had been previously hydrated to reach 31% moisture, were kindly provided by Lavazza S.p.A (Settimo Torinese, Turin, Italy) and stored in vacuum bags. The densities of the dry coffee (710 kg/m3) and wet coffee (550 kg/m3) were calculated in order to select the most appropriate volume for the experiments. The more suitable amount used for the experiments was 185 g of wet coffee (water 31%) corresponding at 144.5 g of dry coffee (water 11%). A remarkable swelling of green coffee beans in water was observed during the humidification process. A caffeine standard (99.7%) was purchased from Alfa Aesar (Karlsruhe, Germany). Acetonitrile, trifluoroacetic acid (TFA) and magnesium oxide (MgO) were obtained from Merck KGaA (Darmstadt, Germany).

2.2. Supercritical CO2 Extraction (SFE–CO2) and Ultrasound-Assisted Supercritical CO2 Extraction (US–SFE–CO2)

The SFE–CO2 and US–SFE–CO2 of caffeine from green coffee beans were performed in a prototype designed and assembled by Weber Ultrasonics GA (Karlsbad, Germany) and FeyeCon B.V. (Weesp, The Netherlands). The prototype was equipped with a system that circulated fluid through the extraction chamber (11–13 kg h−1 of CO2), an insulating jacket and an immersion titanium horn for US-assisted procedures.
For SFE–CO2, green coffee beans were weighed (185 g) and placed into the 1 L-capacity extraction vessel. Different pressure and temperature conditions were tested. Moreover, SFE–CO2 efficiency was compared to that of the extraction with liquid CO2 (LE–CO2), with pressure and temperature being set under the critical point. Similar conditions used in SFE–CO2 were applied for US–SFE–CO2. US assistance was obtained thanks to a probe system equipped with a titanium horn (40 kHz; P = 90% W) that was placed in the extraction vessel. To avoid localized sample overheating, the horn was set to operate 5 min on and 2 min off for the whole extraction time (see Table 1 for tested conditions).
Each procedure was repeated three times to verify extraction method reproducibility, and all of the processes provided an aqueous extract that was subsequently freeze dried (Freeze drier LyoQuest-85, Telstar, Legnano, Italy). A 0.5 mg/mL aqueous solution of each obtained sample was prepared and transferred into a vial for UPLC-MS/MS analysis. Results are expressed as mean data ± standard deviation (SD).

2.3. Conventional Caffeine Extraction

In order to evaluate the total caffeine content in the green coffee beans used for the experiments, a conventional extraction was performed. Briefly, 100 mL of water and 4 g of MgO were added to 1 g of ground green coffee beans, and the obtained mixture was stirred for 1 hour at 90 °C, then filtered. The filtrate was brought to 250 mL with water and placed into a 250 mL graduated flask, and this solution was used for caffeine quantification via UPLC-MS/MS. The procedure was repeated three times to evaluate extraction-yield reproducibility. The efficiency of this conventional extraction method was confirmed by re-extracting, under the same conditions, the residual coffee sample derived from the filtration procedure.

2.4. Qualitative and Quantitative Analyses

Analyses were performed using a UPLC-MS/MS system (Acquity TQD LC/MS/MS System, Waters Corporation, Milford, MA, USA), equipped with a C-18 column (BEH C-18, 2.1 × 50mm, 1.7 µm). Isocratic elution was carried out at 50 °C with 90:10 v/v of water (0.1% TFA)/acetonitrile (0.1%TFA). The flow rate was set at 0.4 mL min−1.
For determination, we operated in atmospheric-pressure chemical ionization (APCI+) mode, following the transitions m/z = 195 -> 138 (quantification) and m/z = 195 -> 110 (qualitative confirmation of the peak), using 26 eV as the collision energy. The calibration curve of the UPLC-MS/MS method was determined using aqueous caffeine standard solutions (from 0.01 to 1 mg/mL); a linear regression with R2 = 0.9994 was obtained using Waters QuanLynx software (LOD 0.005 mg/mL, LOQ 0.01 mg/mL).

3. Results and Discussion

3.1. SFE–CO2, LE–CO2 and US–SFE–CO2 of Green Coffee Beans

Computational simulation studies on caffeine extraction from a fixed bed of coffee beans indicate that acoustic waves could significantly accelerate the kinetics of SFE thanks to their physical/mechanical effects on the treated vegetal matrix, therefore leading to an improvement of extraction rate and yield [9]. To the best of our knowledge, effective experimental works involving the hybrid technology US–SFE–CO2 in coffee decaffeination have not been reported so far.
This study aims to evaluate the possibility of using the effect of cavitation to improve the SFE–CO2 of caffeine from Arabica green coffee beans, in terms of reducing the process time and temperature and also enriching extracts.
Several experiments were carried out under US assistance, and silent conditions, using samples with 31% moisture. It was decided that all tests would be performed in a relatively short process time (1 h), although that does not lead to exhaustive caffeine extraction, which is an operation that usually requires several hours [10]. Nevertheless, under these conditions, a preliminary assessment of the beneficial effects of US–SFE–CO2 was performed. The highest extraction temperature was set at 75 °C.
Different conditions were applied in the first runs using SFE–CO2 alone. The extraction vessel was filled to about 80% maximum volume with 185g of matrix (Table 1, entry one and two). For the sake of comparison, LE–CO2 (Table 1, entry three) was also performed. US–SFE–CO2 was then initially carried out under the same experimental conditions as in SFE–CO2 (Table 1, entries four and five). Subsequently, the influence of both lower pressure and sample amount were tested at the highest temperature (Table 1, entries six and seven, respectively).
Qualitative and quantitative analyses were performed using UPLC-MS/MS on the freeze-dried extracts in order to evaluate caffeine extraction yields and sample enrichment. Data (Table 1) were compared to the mean caffeine content in coffee (9.46 mg/g) obtained from exhaustive conventional water extraction in order to calculate the decaffeination percentage achieved.
Results clearly show that temperature plays a crucial role in extractions carried out under silent conditions (entries one, two and three). Although a poor extraction yield was observed when CO2 was used in liquid conditions, extract purity was relatively high. Under supercritical conditions, yields were found to be directly correlated to increasing temperature and also gave better extract purity, which reached 83.2% at 75 °C. Despite reports by Machmudah et al. [8] on the solubility of caffeine in SC–CO2 at pressures above 19 MPa/190 bar, caffeine solubility increases with increasing temperature, which however is in agreement with Saldana et al. [19].

3.2. US–SFE–CO2 Efficiency

By comparing entries one and four, both carried out at 75 °C and 250 bar, it is possible to see that caffeine amount and decaffeination percentages were doubled thanks to the cavitation phenomenon. A better result if compared with data reported by Farouk & Hasan [14], that showed an enhancement of caffeine extraction yield by around 15%–25%. Moreover, our results evidenced the effect of sonication on extract purity (90.1%). A similar trend can be observed when comparing entries two and five, which were performed at low temperature (40 °C). These preliminary results demonstrate how US is a potential, efficient way of enhancing mass transfer processes in SFE. The use of US enabled higher yields in a shorter time, in agreement with Rodríguez et al. [20] who observed 109%–150% improvement at 30 min comparing SFE–CO2 and US–SFE–CO2 in cocoa butter extraction.
Lower pressure (125 vs. 250 bar) and lower filling volume (50 g vs. 185) (entry six and seven, respectively) confirmed the pivotal role of CO2 pressure [21] as well as a better sound wave diffusion in the sonication cone of the horn tip. Entry four gave up to 90.1% of caffeine in the extract and 18.19% of sample decaffeination. The obtained results showed that the caffeine extraction yield was lower, by about 12%, at 125 bar (entry six). US intensity must be strong enough to induce vibrational effects [22] when a probe system equipped with a titanium horn (40 kHz; P = 90% W) was employed. In the case of a lower sample amount in the extraction vessel (entry seven) higher mass extraction was achieved; a caffeine amount of 2.97 mg per gram of coffee bean was raised, whereas 1.72 mg/g was obtained in entry four. These values reveal that there is an increase in the sonication effect when less vessel volume was occupied by the matrix, thus allowing for better propagation of acoustic waves at lower pressure. Anyway, under these conditions, extracts showed 20% less of caffeine content. This, as observed by field emission scanning electron microscopy by Balachandran et al. [23] that reported 200 µm surface damage in ginger particles, is more likely due to stronger cell-wall rupture and then to higher metabolite release, which results in our case in a lower selectivity for caffeine.
In order to evaluate decaffeination kinetics, the best extraction conditions (entry four) were used for longer times, 2, 3, 4 h (entries eight, nine, ten). It was found that longer extraction times gave a higher decaffeination percentage, up to 63.1% after 4 h, with no significant influence on extract purity.

4. Conclusions

In this preliminary study on caffeine extraction from Arabica green coffee beans, SFE–CO2 and US–SFE–CO2 have been compared under different experimental conditions. Results show that, in 1 h of extraction time, the effect of acoustic waves can lead to a doubling of caffeine extraction yield and around 10% higher extract purity. The best experimental parameters (US–SFE–CO2, 75 °C, 250 bar, 185g of sample amount) were also tested at longer process times, and thus 63.1% decaffeination was achieved in 4 h. These experimental data lay the foundation for further studies into caffeine US–SFE–CO2 from coffee beans, both as an improvement of the decaffeination process in the coffee industry, and as an effective technique to produce purer extracts in shorter times for industrial use.

Author Contributions

Conceptualization, A.B. (Arianna Binello) and G.C.; methodology, J.M. and G.C.; validation, A.B. (Alessandro Barge); formal analysis A.B. (Alessandro Barge); investigation, J.M.; data curation, J.M.; writing—original draft preparation, J.M. and A.B. (Arianna Binello); writing—review and editing G.C.; supervision, G.C. All authors have read and agreed to the published version of the manuscript.

Funding

The Manunet Transnational Call 2019 Project “Ultraclean” is warmly acknowledged.

Acknowledgments

Inga Grigaliunaite (FeyeCon, Weesp-Holand) is warmly acknowledged for the valuable technical assistance.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Vuong, Q.V.; Roach, P.D. Caffeine in green tea: Its removal and isolation. Sep. Purif. Rev. 2014, 43, 155–174. [Google Scholar] [CrossRef]
  2. Global $350M Caffeine Market Outlook and Forecast 2020–2027. Available online: https://www.globenewswire.com/news-release/2020/03/02/1993360/0/en/Global-350M-Caffeine-Market-Outlook-and-Forecast-2020-2027.html (accessed on 1 August 2020).
  3. Shinde, R.R.; Shinde, N.H. Extraction of caffeine from coffee and preparation of anacin drug. Int. J. Eng. Res. Technol. 2017, 10, 236–239. [Google Scholar]
  4. Andreeva, E.Y.; Dmitrienko, S.G.; Zolotov, Y.A. Methylxanthines: Properties and determination in various objects. Russ. Chem. Rev. 2012, 81, 397–414. [Google Scholar] [CrossRef]
  5. Belay, A.; Ture, K.; Redi, M.; Asfaw, A. Measurement of caffeine in coffee beans with UV/vis spectrometer. Food Chem. 2008, 108, 310–315. [Google Scholar] [CrossRef]
  6. Kumar, V.; Ravishankar, G.A. Current trends in producing low levels of caffeine in coffee berry and processed coffee powder. Food Rev. Int. 2009, 25, 175–197. [Google Scholar] [CrossRef]
  7. Hasan, N.; Farouk, B. Mass transfer enhancement in supercritical fluid extraction by acoustic waves. J. Supercrit. Fluids 2013, 80, 60–70. [Google Scholar] [CrossRef]
  8. Machmudah, S.; Kitada, K.; Sasaki, M.; Goto, M.; Munemasa, J.; Yamagata, M. Simultaneous Extraction and Separation Process for Coffee Beans with Supercritical CO2 and Water. Ind. Eng. Chem. Res. 2011, 50, 2227–2235. [Google Scholar] [CrossRef]
  9. Reddy, V.; Saharay, M. Solubility of Caffeine in Supercritical CO2: A Molecular Dynamics Simulation Study. J. Phys. Chem. B 2019, 123, 9685–9691. [Google Scholar] [CrossRef]
  10. Marco, I.D.; Riemma, S.; Iannone, R. Life cycle assessment of supercritical CO2 extraction of caffeine from coffee beans. J. Supercrit. Fluid 2018, 133, 393–400. [Google Scholar] [CrossRef]
  11. Araújo, M.N.; Paladonai, A.Q.; Azevedo, L.; Hamerski, F.; Pedersen Voll, F.A.; Corazza, M.L. Enhanced extraction of spent coffee grounds oil using high-pressure CO2 plus ethanol solvents. Ind. Crop. Prod. 2019, 141, 111723. [Google Scholar] [CrossRef]
  12. Chemat, F.; Rombaut, N.; Sicaire, A.-G.; Meullemiestre, A.; Fabiano-Tixier, A.-S.; Abert-Vian, M. Ultrasound assisted extraction of food and natural products. Mechanisms, techniques, combinations, protocols and applications. A review. Ultrason. Sonochem. 2017, 34, 540–560. [Google Scholar] [CrossRef] [PubMed]
  13. Wen, L.; Zhang, Z.; Sun, D.-W.; Sivagnanam, S.P.; Tiwari, B.K. Combination of emerging technologies for the extraction of bioactive compounds. Crit. Rev. Food Sci. Nutr. 2020, 60, 1826–1841. [Google Scholar] [CrossRef] [PubMed]
  14. Farouk, B.; Hasan, N. Acoustic wave generation in near-critical supercritical fluids: Effects on mass transfer and extraction. J. Supercrit. Fluids 2015, 96, 200–210. [Google Scholar] [CrossRef]
  15. Shirsath, S.R.; Sonawane, S.H.; Gogate, P.R. Intensification of extraction of natural products using ultrasonic irradiations—A review of current status. Chem. Eng. Process. Proc. Intens. 2012, 53, 10–23. [Google Scholar] [CrossRef]
  16. Heilmann, W. Decaffeination of Coffee. In Coffee: Recent Developments; Clarke, R.J., Vitzthum, O.G., Eds.; Blackwell Science Ltd.: London, UK, 2001; pp. 108–124. [Google Scholar]
  17. Dassoff, E.S.; Li, Y.O. Mechanisms and effects of ultrasound-assisted supercritical CO2 extraction. Trends Food Sci. Technol. 2019, 86, 492–501. [Google Scholar] [CrossRef]
  18. Riera, E.; Blanco, A.; García, J.; Benedito, J.; Mulet, A.; Gallego-Juárez, J.A. High-power ultrasonic system for the enhancement of mass transfer in super-critical CO2 extraction processes. Phys. Proced. 2010, 3, 141–146. [Google Scholar] [CrossRef] [Green Version]
  19. Saldana, M.D.A.; Mohamed, R.S.; Baer, M.G.; Mazzafera, P. Extraction of purine alkaloids from mate (Ilex paraguariensis) using supercritical CO2. J. Agric. Food Chem. 1999, 47, 3804–3808. [Google Scholar] [CrossRef]
  20. Rodríguez, Ó.; Ortuño, C.; Simal, S.; Benedito, J.; Femenia, A.; Rosselló, C. Acoustically assisted supercritical CO2 extraction of cocoa butter: Effects on kinetics and quality. J. Supercrit. Fluids 2014, 94, 30–37. [Google Scholar]
  21. Tang, W.Q.; Li, D.C.; Lv, Y.X.; Jiang, J.G. Extraction and removal of caffeine from green tea by ultrasonic-enhanced supercritical fluid. J. Food Sci. 2010, 75, C363–C368. [Google Scholar] [CrossRef]
  22. Hu, A.; Zhao, S.; Liang, H.; Qiu, T.; Chen, G. Ultrasound assisted supercritical fluid extraction of oil and coixenolide from adlay seed. Ultrason. Sonochem. 2007, 14, 219–224. [Google Scholar] [CrossRef]
  23. Balachandran, S.; Kentish, S.E.; Mawson, R.; Ashokkumar, M. Ultrasonic en- hancement of the supercritical extraction from ginger. Ultrason. Sonochem. 2006, 13, 471–479. [Google Scholar] [CrossRef] [PubMed]
Table 1. Experimental conditions for caffeine extraction from Arabica green coffee beans and caffeine determination using UPLC-MS/MS analyses. Reported data are the mean of two experiments.
Table 1. Experimental conditions for caffeine extraction from Arabica green coffee beans and caffeine determination using UPLC-MS/MS analyses. Reported data are the mean of two experiments.
EntrySample (g)Temperature (°C)Pressure (bar)Extraction MethodTotal Caffeine (mg)Extract Caffeine %Caffeine mg/g Coffee BeansDecaffein. %Time (h)
1185752501 a155.1 ± 10.683.2 ± 5.90.838 ± 0.068.86 ±0.611
2185402501 a59.2 ± 4.576.2 ± 5.80.320 ± 0.023.38 ± 0.261
318520702 b26.3 ± 3.880.2 ± 11.60.142 ± 0.021.50 ± 0.211
4185752503 c318.3 ± 19.790.1 ± 5.61.72 ± 0.118.19 ± 1.11
5185402503 c126.5 ± 10.483.9 ± 6.90.684 ± 0.067.23 ± 0.61
6185751253 c279.8 ± 15.874.1 ± 4.21.51 ± 0.0815.98 ± 0.91
750752503 c148.5 ± 9.369.0 ± 4.32.97 ± 0.1831.4 ± 1.91
8185752503 c673.8 ± 25.887.3 ± 3.33.64 ± 0.1238.5 ± 1.42
9185752503 c906.5 ±30.691.6 ± 3.16.04 ± 0.251.8 ± 1.83
10185752503 c1104.3 ± 40.193.4 ± 3.35.97 ± 0.263.1 ± 2.34
a Supercritical CO2 extraction (SFE–CO2); b extraction with liquid CO2 (LE–CO2); c ultrasound supercritical CO2 extraction (US–SFE–CO2).

Share and Cite

MDPI and ACS Style

Menzio, J.; Binello, A.; Barge, A.; Cravotto, G. Highly-Efficient Caffeine Recovery from Green Coffee Beans under Ultrasound-Assisted SC–CO2 Extraction. Processes 2020, 8, 1062. https://0-doi-org.brum.beds.ac.uk/10.3390/pr8091062

AMA Style

Menzio J, Binello A, Barge A, Cravotto G. Highly-Efficient Caffeine Recovery from Green Coffee Beans under Ultrasound-Assisted SC–CO2 Extraction. Processes. 2020; 8(9):1062. https://0-doi-org.brum.beds.ac.uk/10.3390/pr8091062

Chicago/Turabian Style

Menzio, Janet, Arianna Binello, Alessandro Barge, and Giancarlo Cravotto. 2020. "Highly-Efficient Caffeine Recovery from Green Coffee Beans under Ultrasound-Assisted SC–CO2 Extraction" Processes 8, no. 9: 1062. https://0-doi-org.brum.beds.ac.uk/10.3390/pr8091062

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop