Next Article in Journal
Whole-Body Acute Contact Toxicity of Formulated Insecticide Mixtures to Blue Orchard Bees (Osmia lignaria)
Next Article in Special Issue
An Easy Procedure to Quantify Anticoagulant Rodenticides and Pharmaceutical Active Compounds in Soils
Previous Article in Journal
Novel QSAR Models for Molecular Initiating Event Modeling in Two Intersecting Adverse Outcome Pathways Based Pulmonary Fibrosis Prediction for Biocidal Mixtures
Previous Article in Special Issue
2,2-Bis(4-Hydroxyphenyl)-1-Propanol—A Persistent Product of Bisphenol A Bio-Oxidation in Fortified Environmental Water, as Identified by HPLC/UV/ESI-MS
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

A Toolbox for the Determination of Nitroaromatic Explosives in Marine Water, Sediment, and Biota Samples on Femtogram Levels by GC-MS/MS

Institute of Toxicology and Pharmacology for Natural Scientists, University Medical School Schleswig-Holstein, Brunswiker Straße 10, 24105 Kiel, Germany
*
Author to whom correspondence should be addressed.
Submission received: 12 February 2021 / Revised: 7 March 2021 / Accepted: 12 March 2021 / Published: 16 March 2021

Abstract

:
To determine the amount of the explosives 1,3-dinitrobenzene, 2,4-dinitrotoluene, 2,4,6-trinitrotoluene, and its metabolites in marine samples, a toolbox of methods was developed to enhance sample preparation and analysis of various types of marine samples, such as water, sediment, and different kinds of biota. To achieve this, established methods were adapted, improved, and combined. As a result, if explosive concentrations in sediment or mussel samples are greater than 10 ng per g, direct extraction allows for time-saving sample preparation; if concentrations are below 10 ng per g, techniques such as freeze-drying, ultrasonic, and solid-phase extraction can help to detect even picogram amounts. Two different GC-MS/MS methods were developed to enable the detection of these explosives in femtogram per microliter. With a splitless injector, limits of detection (LODs) between 77 and 333 fg/µL could be achieved in only 6.25 min. With the 5 µL programmable temperature vaporization—large volume method (PTV-LVI), LODs between 8 and 47 fg/µL could be achieved in less than 7 min. The detection limits achieved by these methods are among the lowest published to date. Their reliability has been tested and confirmed by measuring large and diverse sample sets.

1. Introduction

The release of nitro-aromatic explosives from corroding marine-dumped munitions is a worldwide problem with growing environmental concern [1]. In Germany alone, it is assumed that 1.8 million metric tons of conventional munitions were dumped into the North and Baltic Seas during or after the First and Second World Wars, and 1.6 million metric tons of these munitions are still rusting at the seafloor to date [2]. For 2,4,6-trinitrotoluene (TNT), one of the main explosives used in bombs, grenades, mines, and torpedoes, accumulation has been proven in marine organisms, such as the blue mussel Mytilus edulis [3,4,5,6] and dab Limanda limanda [7,8]. In order to assess contamination of the North Sea and the Baltic Sea by the legacy of war as comprehensively as possible, with regard to present and future ecotoxicological consequences, the examination of large quantities of various abiotic and biotic samples for TNT, its metabolites, and other munitions components such as 1,3-dinitobenzene and 2,4-dinitrotoluene is required.
Gas and liquid chromatography techniques have been routinely used in the detection of nitro-organic explosives for over fifty years [9,10]. Coupled with mass selective detectors, they not only allow quantitative analysis but also qualitative screening for unknown substances or unsuspected compounds in samples. Modern mass spectrometric techniques, such as triple, quadrupole, or Orbitrap mass spectrometry, allow limits of detection, depending on the components, in the range of femto- to atto-gram per injection [11]. Several publications have since been published dealing with the detection of various explosives and their metabolites in quite different matrices, such as the EPA methods 529 (explosives in drinking water by GC/MS) [12], 8330 (water, soil, and sediment by HPLC) [13], and 8095 (explosives by gas chromatography) [14]. Fields addressed in these publications were exposure to legacies of land-based warfare [15], anti-terror [16], or forensic issues such as the detection of minute traces of explosives in evidence such as clothing and containers [17]. However, more than twenty years ago, research groups have investigated the release of explosives into seawater at marine munitions dumping grounds [18]. Regarding the detection of explosives in marine samples, a whole series of articles have been published in recent years, e.g., for water [19], sediment [19,20], blue mussels [3,4,5,6], and dab [7,8].
In abiotic samples, such as water or sediments, larger concentrations of unmetabolized TNT were found, while it is rarely detectable in biota samples, e.g., in the bioindicator mussel Mytilus spp. [3]. Here, mainly TNT metabolites such as 4-amino-2,6-dinitrotoluene (4-ADNT), and to a lesser extent, 2-amino-4,6-dinitrotoluene (2-ADNT), were found [3]. Additionally, biota samples contain large quantities of polar organic molecules, such as fatty acids and steroids, the so-called sample matrix, which coelute during the extraction of the explosives and, therefore, interfere with the analytical material. In abiotic samples, the proportion of soluble matrix is usually lower.
In this study, sample preparation methods were developed and optimized for the detection of TNT, its metabolites 2- and 4-ADNT, and the explosive byproducts 1,3-dinitrobenzene (1,3-DNB) and 2,4-dinitrotoluene (2,4-DNT). The goal was to develop a toolbox of methods that enable the detection of these compounds in different abiotic and biotic samples at sub-nanogram levels. Depending on the expected concentrations, many samples can either be processed quickly or purified and concentrated better through additional steps to achieve even lower detection limits.

2. Materials and Methods

2.1. Materials and Chemicals

Trinitrotoluene (98.9% purity, 1 mg/mL, in acetonitrile (ACN):methanol (MeOH) 50:50), 1,3-dinitrobenzene (97.0% purity, 1 mg/mL, in ACN:MeOH 50:50), 2,4-dinitrotoluene (98.3% purity, 1 mg/mL, in ACN:MeOH 50:50), 4-amino-2,6-dinitrotoluene (98.4% purity, 1 mg/mL, in ACN:MeOH 50:50), and 2-amino-4,6-dinitrotoluene (97.8% purity, 1 mg/mL, in ACN:MeOH 50:50) were purchased from AccuStandard, New Haven, USA. Isotopically labeled TNT (13C7, 99%; 15N3, 98%, 1 mg/mL in benzene, wetted with >33% H2O) was purchased from Cambridge Isotope Laboratories, Inc., Andover, USA. Acetonitrile (UHPLC-grade, purity ≥ 99.97%) was purchased from Th. Geyer (Renningen, Germany) and used without further purification. CHROMABOND Easy polystyrene-divinylbenzene-copolymer reversed-phase solid-phase extraction columns 80 µm, 3 mL/200 mg (Macherey Nagel, Düren, Germany) were used. Ultrapure water (18.2 MΩ cm) was prepared on-site with a Veolia ELGA Purelab Flex system. Sea water was collected with a 2 L Ruttner water trap (Hydro-Bios, Kiel, Germany) from the Kiel Fjord. Live blue mussels (food grade) were purchased from the Kiel mussel farm and stored at −20 °C before use. Freeze-dried sediments from previous studies, stored at −20 °C, were used.

2.2. Water Sample Preparation

Water samples were prepared by a method adapted from Gledhill et al. (2019) [19]. Seawater (1L) was measured into an EVA infusion bag (ICU Medical, Inc, San Clemente, CA, USA) containing 200 µL of a 250 ng/mL 13C15N-TNT solution as internal standard, and introduced through an unconditioned Chromabond Easy SPE column in the absence of light at 4 °C. The water was then discarded, columns were dried in vacuum (0.5 h) and eluted with 4 mL ACN. The eluate was concentrated to 600 µL using a RVC 2-25 CDplus rotary vacuum concentrator (Martin Christ Gefriertrocknungsanlagen GmbH, Osterode, Germany) and stored in 1.5 mL amber vials at −20 °C.

2.3. Sediment Sample Preparation

Twenty grams of wet sediment were weighed into 100 mL screw top beakers and lyophilized in an Alpha 2–4 LSCplus freeze drier (Martin Christ Gefriertrocknungsanlagen GmbH, Osterode, Germany) for 16–18 h. Samples were homogenized by shaking and 2 g of each was weighed into 15 mL polypropylene tubes. 13C15N-TNT (100 µL of a 250 ng/mL solution) and 4.9 mL ACN were then added, and the samples were shaken on a VF2 vortex mixer (Ika Works Inc., Staufen im Breisgau, Germany) for 60 s, prior to sonication for 15 min (Bandelin Sonorex Super RK 510 H, BANDELIN electronic GmbH & Co. KG, Berlin, Germany). After 10 min of centrifugation (4100 rpm, 4 °C, Heraeus Megafuge 11 R, Thermo Fisher Scientific Inc., Waltham, MA, USA), supernatants were filtered through 0.22 µm PTFE filters, concentrated to 600 µL using a Christ RVC 2-25 CDplus rotary vacuum concentrator and stored in 1.5 mL amber vials at −20 °C.
To achieve lower limits of detection, 100 g wet sediment were mixed with 250 mL bidest water, shaken for 80 min, sonicated for 15 min, centrifuged (4500 rpm at 10 °C for 15 min; J2-HS centrifuge, Beckman Coulter GmbH, Krefeld, Germany), filtered through a 595 1/2 pleated filter and introduced into SPE-columns using mild vacuum. Columns were dried for 30 min i.vac., eluted with 4 mL ACN, concentrated to 600 µL, and stored at −20 °C in 1.5 mL amber vials.

2.4. Mussel Sample Preparation

Fresh mussels were prepared according to Strehse et al. 2017 [3]. Mussels were thawed, homogenized using an IKA T25 ULTRA Turrax (IKA Werke GmbH & Co. Kg, Staufen im Breisgrau, Germany) and aliquoted as 1 g portions into 15 mL polypropylene tubes. Five milliliters ACN was added to each sample, and samples were vortexed for 1 min and centrifuged for 10 min (4100 rpm, 4 °C). The supernatants were transferred to 10 mL graded flasks and made up to 10 mL with ACN. One milliliter of each solution was transferred into a 1.5 mL amber vial containing 50 ng 13C15N-TNT and stored at −80 °C.
For solid-phase extraction, mussels were freeze-dried for 48–72 h. Lyophilized mussels were homogenized using an IKA A11 basic analytical mill (IKA Werke GmbH & Co. Kg, Staufen im Breisgrau, Germany), and aliquots of 150–500 mg were weighed into lightproof 5 mL tubes. An amount of 1.9 mL ACN and 100 µL of a 50 ng/mL 13C15N-TNT solution were added as internal standard, then samples were vortexed for 60 s, sonicated for 15 min, and centrifuged at 4100 rpm (4 °C) for 15 min. Supernatants were transferred into 25 mL graded flasks, made up with ultrapure water, and introduced onto unconditioned Chromabond Easy SPE-columns using a mild vacuum. Columns were then dried i.v.ac for 30 min, and samples were eluted with 4 mL ACN, concentrated to 600 µL, and stored at −80 °C in 1.5 mL amber vials.

2.5. GC-MS/MS Analysis

A Thermo Scientific TRACE 1310 gas chromatograph, equipped with a split/splitless-injector (SSL) and a programmable temperature vaporization (PTV) injector, a TriPlus 100 LS autosampler, and coupled to a TSQ 8000 EVO triple quadrupole mass spectrometer with electron ionization source was used. The GC was equipped with a TraceGold TG-5MS amine 15 m × 0.25 mm × 0.25 µm column (Thermo Fisher Scientific Inc., Waltham, MA, USA) and was connected to the respective injector. Splitless injections on the SSL injector were performed on quartz wool (Thermo Fisher Scientific Inc., Waltham, MA, USA) or CarboFrit (Restek Coorperation, Bellefonte, PA, USA) injection port liner (dimensions: 4 mm × 6.5 mm × 78.5 mm), while large-volume injections were carried out on the PTV-injector with packed quartz wool liners (2 mm × 2.75 mm × 120 mm, Thermo Fisher Scientific Inc., Waltham, MA, USA)). Helium served as a carrier gas for the GC, and Argon as collision gas for the mass spectrometer (both Alphagaz, purity 99.999%). Spectra were recorded and analyzed in TraceFinder 4.1 and Chromeleon 7.2 (Thermo Fisher Scientific Inc., Waltham, MA, USA). GC-MS/MS programs developed for this study are outlined in Table 1.

2.6. External and Internal Standards

External standards were prepared by diluting a 100 µg/mL solution of each of the five explosives with ACN to obtain concentrations of 0.1–100 ng/mL. Calibration curves were automatically calculated by the software Chromeleon, based on double injections of a standard row before each batch of samples. During measurements, an external standard in the order of magnitude of the expected concentrations was injected at regular intervals between samples. For TNT, isotopically pure 13C15N-TNT was used as the internal standard. Solutions of 50, 250, and 500 ng/mL ACN were prepared, and depending on the desired standard concentration, 100 uL of one of the solutions were added to the samples. The signals of both internal and external standards were used to compensate for the change in signal intensity caused by matrix effects over the course of measurements. To check for carry-over effects, a blank solvent was measured before each external standard. Even with concentrations of up to 1000 ng/mL, no carry-over was observed.

2.7. Matrix Standards

Matrix-specific limits of detection and quantification were determined with spiked matrix samples. Uncontaminated sediments and mussel samples from previous investigations, as well as water from the Kiel Fjord and 18.2 MΩ cm ultrapure water, were used. From previously freeze-dried sediments, 2 g aliquots were prepared as described above, concentrated to 600 µL, and spiked with all five explosive chemicals at concentrations of 0.1–0.9 ng/mL. Water samples from Kiel Fjord were extracted in the solid phase, concentrated to 600 µL, and spiked in the same manner. Since explosives were found in the Fjord water at concentrations ranging from 0.12–2.2 ng/L, additional ultrapure water was concentrated through Chromabond Easy SPE columns and the eluates were spiked with explosives at concentrations from 0.1 to 0.9 ng/mL of the explosives. Mussels, purchased from the Kiel mussel farm in August 2020, were prepared according to Strehse et al. 2017 [3] and spiked with 0.1 to 0.9 ng/mL of the explosives. The second set of mussels samples was prepared using the freeze-drying and solid-phase extraction method and was spiked from 0.01 to 0.09 ng/mL, as well as from 0.1 to 0.9 ng/mL. The detection limits for all samples were determined using the splitless quartz wool liner method. Additionally, for the freeze-dried mussels, the programmable temperature vaporization—large volume method (PTV-LVI) method was tested.

3. Results

3.1. GC-MS/MS Method Development and Optimization

The mass spectrometer was operated in secondary reaction monitoring mode, as this allows reliable detection of the substances even at very low concentrations. The quantitative and qualitative transitions observed, and the corresponding collision energies are also presented in Table 2. The instrumental Limits of Detection determined for both methods can be found in Table 3. Figure 1 shows the chromatograms of different concentrations used to determine them.

3.1.1. Splitless Injection Methods

The splitless technique allows injection of up to 1 µL without the use of a retention gap. In splitless injection, the sample is injected into the liner at a temperature well above the boiling point of the solvent. Irrespective of their boiling points, all analytes are vaporized at the same temperature immediately after injection.
To determine the optimal injector temperature, 1 µL of a 10 ng/mL mixture of 1,3-DNB, 2,4-DNT, TNT, 4-ADNT, and 2-ADNT was injected into a splitless packed quartz wool liner at various temperatures between 180 °C and 300 °C, and the peak areas of the compounds were recorded. Thus, 230 °C was determined as the optimum injection temperature, as shown Figure 2a. According to Emmrich et al. 2001 [21], the use of packed CarboFrit liner instead of quartz wool is highly recommended. The same packing material was used by Marder et al. (2018) [22]. Initial experiments with an injector temperature of 290 °C almost resulted in a complete loss of the TNT peak from the second injection onwards, so temperatures between 180 and 280 °C were tested. The highest intensities were obtained at a temperature of 270 °C (Figure 2b). Although initial tests looked promising, CarboFit liners did not provide a clear advantage over the more favorable quartz wool liners within the detection limits (Table 3).
Since many of the explosives are temperature sensitive (e.g., TNT starts to decompose around 150 °C [23,24]), the dwell time on the column was minimized by a rapid oven program, and the 15 m column was used instead of 30 m. Thermo Fisher Scientific TG-5MS amine columns, which are specially deactivated to reduce tailing of amines such as 2- and 4-ADNT, were found to provide better results compared to standard 5% diphenyl/95% dimethyl-polysiloxan phases. Columns were trimmed by 5 cm each time the liner was exchanged.
The initial oven temperature was set to 100 °C to prevent condensation of the solvent on the column. Higher initial temperatures resulted in a peak broadening of 1,3-DNB. After a 0.20 min condensation phase, the oven temperature was increased by 30 °C/min. This was the highest rate at which 4- and 2-ADNT could still be clearly separated. The retention times are between 2.43 min (1,3-DNB) and 4.42 min (2-ADNT), as presented in Table 2. After 2-ADNT has left the column, it was heated to 280 °C at 80 °C/min and held for one minute to remove low volatile compounds. Thus, a total runtime of only 6.25 min could be achieved.

3.1.2. PTV Large Volume Injection Method

Different types of liners were tested; packed quartz wool, CarboFrit, baffled glass, and sintered glass. Although the latter allows the highest injection volumes; in preliminary tests, up to 50 µL were tested with standards in acetonitrile, these liners are extremely susceptible to contamination by matrix components due to the dense glass mesh. Initial tests with spiked water and mussel samples showed a rapid decrease in peak intensities after only a few injections, even when the injection volume was reduced to 5 µL. This was accompanied by a clearly visible discoloration of the liner. They were, therefore, not used further for method development. According to the manufacturer, baffled liners are suitable for volumes up to 10 µL; however, no satisfactory results could be obtained here. After a few measurements, strong turbidity of the column end could be observed, which indicates insufficient retainment of the sample solution in the liner before evaporation. The best results were obtained with quartz wool which, however, limits the injection volume to <10 µL.
Five µL was chosen as the best compromise between detection limit and wear. A solvent split of 0.18 min at 70 °C and 50 mL/min split flow was set at the beginning of the injector heating program, followed by a 5 °C/s temperature increase to a final temperature of 240 °C. The remaining low volatile compounds were removed from the liner by 200 mL/min split-flow 1.5 min after the final temperature was reached.
The oven program of the splitless method was adapted. Due to the solvent split, the initial time at 100 °C was increased from 0.2 to one minute. The heating rate was set for 35 °C/min to 220 °C (0.7 min), and by 70 °C/min to 280 °C. Total run time was just under 7 min. Due to the solvent split at the beginning of the heating program, the retention times in the PTV method were somewhat longer than the splitless method. They are between 3.20 min (1,3-DNB) and 5.07 min (2-ADNT) and can be found in Table 2. Instrumental Limits of Detection of the PTV-LVI method can be found in Table 3; Figure 1c shows the chromatograms from 0.00 to 0.09 ng/mL which were used to determine them.

3.2. Improvement of Sample Preparation

3.2.1. Water Samples

In previous studies, conducted directly at the surface of exposed explosives, TNT concentrations of more than 3 mg/L were measured, but these concentrations decreased to 3.3 µg/L at a distance of only 50 cm from the exposure site [25]. In open water, concentrations ranging from <0.5–>7.1 ng/L were detected in a large number of water samples collected from 114 stations during a research cruise along the German Baltic coast, with the highest concentrations found in nearshore water and near the bottom [26].
The method of water sampling was adopted from Gledhill et al. 2019 [19] and adapted slightly. In the current study, bags were connected to the upper end of the column, via a homemade adapter instead of the Luer lock connection at the bottom, and the eluate was concentrated to 600 µL in vacuum.
The effect of preconditioning on the performance of columns, as mentioned in the Macherey Nagel application database, was tsted; since manufacturers advertised these columns as ready-to-use. Preconditioning with acetone followed by water, ACN followed by water, and acetone followed by ACN were tested against the unconditioned columns in terms of process efficiency by extracting 10 ng of each explosive from 1 L ultrapure water. Process efficiency, matrix effect, and recovery efficiency were determined for the unconditioned columns (Figure 3a). No major advantage was found for the conditioning step regarding the process efficiency (Figure 3b).

3.2.2. Sediment Samples

For sediment samples, the method published in the UDEMM Best Practice Guide [27] was initially used. Twenty grams of sediment were measured and freeze-dried. The average weight lost during drying was 24.9 ± 3.8% (n = 18). From the homogenated samples, 2 g were weighed for preparation. Previous tests have shown that explosive concentrations in sediments are often very low, and occur only when sediment and munitions are in direct contact. They can be found in the samples. Even in an area with TNT concentrations of more than 50 pg/g water, sediment concentrations were below 1 pg/g. Therefore, in order to detect even lower amounts of explosives in sediment samples, a method was developed using solid-phase extraction for 100 g non-freeze-dried sediment. With this method, explosive concentrations of less than 10 pg/g sediment could be detected in samples collected close to sunken warships. TNT (0.6 ng/mL, corresponding to 6 pg/g weight), 4-ADNT (0.3 ng/mL, 3 pg/g weight), and 2-ADNT (0.5 ng/mL, 5 pg/g weight) were detected in a sample in which no explosives were measured in 2 g of freeze-dried material (Figure 4).

3.2.3. Mussel Samples

While the method of mussel preparation published by Strehse et al. 2017 [3] was capable of proving the accumulation of TNT and its metabolites and allows quick and simple preparation of large quantities of samples, its limits of detection were relatively high (1.2–3.5 ng/g wet weight). This was because the mussels were homogenized as a whole and thus contained large quantities of water. Moreover, samples were then aliquoted into 1 g portions in 10 mL of ACN, thus equaling only 0.1 g of whole mussel tissue per mL. In open water experiments with mussels transplanted in the dumping area Kolberger Heide, concentrations of up to 31.0 ng/g w.w. TNT, 131.3 ng/g w.w. 4-ADNT, and 103.8 ng/g w.w. 2-ADNT were recorded in mussels after 93 days of exposure, which were placed directly on free-lying hexanite (German: “Schiesswolle”) [3], while in mussels exposed in similar time frames in the vicinity of corroding mines only 4-ADNT could be detected at concentrations of 2.4–7.8 ng/g w.w. [4]. Furthermore, a near-linear decrease in 4-ADNT concentration was observed; between 10 cm and 1 m vertical distance, it had decreased by almost 90% [5]. Therefore, for mussels placed in open water from less polluted areas, 4-ADNT concentrations well below 1 ng/g w.w. can be expected.
To achieve lower limits of detection, the water was gently removed from the mussel tissue by freeze-drying. The average dry weight (d.w.) was determined as 10.0 ± 2.1% of the wet weight (w.w.) (n = 14). Approximately 250 mg of the freeze-dried tissue was extracted in 2 mL ACN by means of an ultrasonic bath. The samples were analyzed using the 5 µL large volume injection programmable temperature vaporization method. Coeluted polar mussel compounds such as fatty acids, sterols, etc., however, resulted in a rapid decrease in sensitivity such that a 1 ng/mL standard mix was not detected after measuring less than 10 samples.
Polytetrafluoroethylene (PTFE) filters, as recommended by Bae et al. [28], were tested to reduce the buildup of coarse mussel debris on the liners, with process efficiencies slightly above 100% for 0.22 and 0.45 µm pore sizes (mussel samples were spiked with 50 or 100 ng/mL of the standard mixture, n = 3).
Furthermore, a solid phase extraction method was developed to separate the explosives from the matrix. An amount of 250 to 500 mg mussel tissue was extracted in 2 mL ACN as described above. After centrifugation, the supernatant was made up to 25 mL in ultrapure water and concentrated by solid-phase extraction. The eluate was concentrated to 600 µL. Freeze-drying prior to processing reduced the detection limits in the mussel samples by a factor of 100, and even by a factor of 1000 in combination with solid-phase extraction (Table 4). The reliability of both methods was tested and confirmed using calibration standards in a series of measurements of actual samples (Figure 5).

3.2.4. Limits of Detection/-Quantification and Linear Range

Limits of detection (LOD) and—quantification (LOQ) of the methods were determined for solvent standards in ACN, water, sediment, and mussels (fresh and lyophilized) by splitless injection on quartz wool liners (SL QW), and for solvent standards as well as lyophilized mussels by the programmable temperature vaporization large volume injection method (PTV LVI). The calibration standard method according to EUR 28,099 EN was used [29]. Matrix blank samples were spiked with a mixture of the analytes in five equidistant steps, from zero to ten times the estimated limit of detection. For each concentration, two independent samples were prepared. The LOD was calculated in an excel sheet, and LOQ was defined as 3.3 times the LOD.
For the SL QW-method, LODs between 95 and 333 fg/µL (equals the quantity on the column) were achieved. Similar or minimally lower detection limits were observed using CarboFrit liners. For the PTV large volume injection method, limits were 3 times (TNT, 47 fg/µL, 235 fg on column) to 12 times (4-ADNT, 8 fg/µL, 40 fg on column) lower. LODs and LOQs for standards prepared in ACN are displayed in Table 3. Linearity was determined for all components between the LOQ and 500 ng/mL (R2 ≥ 0.995).
Due to the small differences between CarboFrit and quartz wool liner, matrix-specific LODs were determined only for the latter. The values obtained were divided by the amount of sample used and thus converted to ng/L or ng/g (w.w. or d.w). The calculation for sediments refers to the extraction of 2 g of lyophilized material. With the extraction of 100 g wet sediment using the solid phase method, 30–50 times lower detection limits could be achieved. Comparing fresh mussels with freeze-dried ones, taking into account the 90% weight loss due to freeze-drying, detection limits achieved for 2- and 4-ADNT were 100-fold lower using SL QW and almost a thousand-fold lower using PTV-LVI. Matrix-specific LODs and LOQs can be found in Table 4.

4. Discussion

Compared to split-/splitless injectors, programmable temperature vaporization injectors have some advantages. With programmable temperature vaporization injectors, the sample is applied to the liner at temperatures below the boiling point of the solvent, which is then heated to a target temperature at a rate of a few degrees per second. Thus, each substance is vaporized at its precise boiling point, and this protects temperature-labile analytes. During this process, the solvent can be selectively evaporated and larger amounts of the analyte can be injected into the liner (up to several 100 µL). However, its disadvantages are the significantly lower liner volumes required (which lead to faster contamination of the packing material by low-volatility matrix components), and the significantly high cost of the liners.
The methods established in this study allow sample- and concentration-dependent preparation, and detection of the five main legacy explosive chemicals from marine-dumped munitions. In accordance with the expected concentration and desired limits of detection, work-up is fast, and with the addition of further cleaning steps such as solid-phase extraction, even the lowest concentrations can be determined. Detection limits from a few tens to a few hundreds of femtograms per microliter could be achieved in all matrices tested.
Compared to Strehse et al., 2017 [3], a combination of freeze-drying and solid-phase extraction allowed a hundred times lower detection limits for 4- and 2-ADNT in mussels when analyzed by splitless injection. These detection limits recorded could also be a thousand times lower when using the PTV injector.
Moreover, this method is excellent for rapid and reliable analysis of large amounts of samples and, with the improvements developed here, allows detection limits between 1.2 and 3.5 ng/g wet weight (equivalent to 12–35 ng/g dry weight). Importantly for both methods, their suitability was proven on large measurement series, as shown in Figure 5.
In comparison with other GC- and LC-MS methods reported in recent years, the detection limits achieved in this study are among the lowest published so far (Table 5). They are more than one order of magnitude lower than those described by Gordon et al. 2018 [20] and Dawidziuk et al. 2018 [30]. Moreover, with the exception of TNT, these detection limits are even more sensitive than those found by Gledhill et al. 2019 [19] using UHPLC-Orbitrap-MS. Only Kirchner et al. 2007 [31] yielded a lower detection limit for TNT and a comparable one for 2,4-DNT. However, their measurements were performed by on-column injection onto a very short column of 5 m, which is likely to lead to very rapid contamination due to the complex matrices in the marine samples. Furthermore, their detection limits were determined from the signal-to-noise ratios, which makes the comparability between the methods difficult.

5. Conclusions

With the methods presented in this study, reliable, fast, and sensitive determination of low explosive concentrations in marine samples, such as water, sediment, and marine biota are possible. The splitless injection method allows rapid measurement in only 6.25 min with limits of detection between 77 to 333 fg/µL. Combined with the applied extraction and sample preparation methods, it can be adapted for multiple types of biotic and abiotic samples. For biota samples (e.g., Mytilus spp.), in which the parent TNT concentration is lower compared to its metabolites, the large volume injection method allows detection limits that are even 10 times lower (of note: 8–47 fg/µL, corresponds 40 to 235 µg on column). Altogether, the methods described in the present investigation are among those with the lowest detection limits published to date and have successfully been proven for their reliability on actual samples, i.e., samples obtained from different scientific research projects [3,4,5,6]. Furthermore, for the splitless method, using over 200 samples, the areas of an external 10 ng/mL standard remained constant for 1,3-DNB, 2,4-DNT, 2- and 4-ADNT, and only decreased by 50% for TNT. This allows automatic measurements over several days. The PTV method has been proven over a batch with 50 samples and has provided consistent results for 2- and 4-ADNT over the entire course of measurement.

Author Contributions

Conceptualization, T.H.B. and J.S.S.; methodology, T.H.B.; validation, T.H.B.; formal analysis, T.H.B.; investigation, T.H.B., T.B., and A.C.H.; resources, T.H.B., J.S.S., and E.M.; writing—original draft preparation, T.H.B.; writing—review and editing, J.S.S. and E.M.; visualization, T.H.B.; supervision, E.M.; project administration, J.S.S. and E.M.; funding acquisition, J.S.S. and E.M. All authors have read and agreed to the published version of the manuscript.

Funding

This work was financially supported by the Schleswig-Holstein Ministry of Energy, Agriculture, the Environment, Nature, and Digitisation (MELUND), the German Environment Agency (UBA), and the INTERREG North Sea Region European Regional Development Fund.

Institutional Review Board Statement

Ethical review and approval were waived for this study, as only invertebrates were used that are not subject to the German Animal Welfare Experimental Animal Ordinance (Tierschutz-Versuchstierverordnung—TierSchVersV).

Data Availability Statement

Data are contained within the article.

Acknowledgments

The authors would like to thank Thomas Stegemann (Thermo Fisher Scientific Inc.) for his help with Chromeleon software and optimization of GC-MS/MS methods and Kristina Andrea Thiemann (Kiel University) for her contribution to the collection, preparation, and measurement of samples.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Bełdowski, J.; Brenner, M.; Lehtonen, K.K. Contaminated by War: A Brief History of Sea-Dumping of Munitions. Mar. Environ. Res. 2020, 162, 105189. [Google Scholar] [CrossRef]
  2. Böttcher, C.; Knobloch, T.; Rühl, N.-P.; Sternheim, J.; Wichert, U.; Wöhler, J. Munitionsbelastung der Deutschen Meeresgewässer—Bestandsaufnahme und Empfehlungen; Bundesamt für Seeschifffahrt und Hydrographie (BSH), Sekretariat Bund/Länder-Messprogramm für die Meeresumwelt von Nord-und Ostsee (BMLP): Hamburg, Germany, 2011; p. 174. [Google Scholar]
  3. Strehse, J.S.; Appel, D.; Geist, C.; Martin, H.-J.; Maser, E. Biomonitoring of 2,4,6-Trinitrotoluene and Degradation Products in the Marine Environment with Transplanted Blue Mussels (m. Edulis). Toxicology 2017, 390, 117–123. [Google Scholar] [CrossRef]
  4. Appel, D.; Strehse, J.S.; Martin, H.-J.; Maser, E. Bioaccumulation of 2,4,6-Trinitrotoluene (TNT) and Its Metabolites Leaking from Corroded Munition in Transplanted Blue Mussels (m. Edulis). Mar. Pollut. Bull. 2018, 135, 1072–1078. [Google Scholar] [CrossRef] [PubMed]
  5. Maser, E.; Strehse, J.S. “Don’t Blast”: Blast-in-Place (BiP) Operations of Dumped World War Munitions in the Oceans Signifi-cantly Increase Hazards to the Environment and the Human Seafood Consumer. Arch. Toxicol. 2020, 94, 1941–1953. [Google Scholar] [CrossRef]
  6. Strehse, J.S.; Maser, E. Marine Bivalves as Bioindicators for Environmental Pollutants with Focus on Dumped Munitions in the Sea: A Review. Mar. Environ. Res. 2020, 158, 105006. [Google Scholar] [CrossRef]
  7. Koske, D.; Straumer, K.; Goldenstein, N.I.; Hanel, R.; Lang, T.; Kammann, U. First Evidence of Explosives and Their Degra-dation Products in Dab (Limanda Limanda L.) from a Munition Dumpsite in the Baltic Sea. Mar. Pollut. Bull. 2020, 155, 111131. [Google Scholar] [CrossRef]
  8. Koske, D.; Goldenstein, N.I.; Rosenberger, T.; Machulik, U.; Hanel, R.; Kammann, U. Dumped Munitions: New Insights into the Metabolization of 2,4,6-Trinitrotoluene in Baltic Flatfish. Mar. Environ. Res. 2020, 160, 104992. [Google Scholar] [CrossRef]
  9. Williams, A.F.; Murray, W.J. Determination of Traces of Ethyleneglycol Dinitrate (and Nitroglycerine) in Blood and Urine. Nature 1966, 210, 816–817. [Google Scholar] [CrossRef]
  10. Alley, B.J.; Dykes, H.W. Gas-Liquid Chromatographic Determination of Nitroglycerine in Pharmaceutical Preparations. J. Chromatogr. 1972, 72, 182–186. [Google Scholar] [CrossRef]
  11. Patterson, D.G.; Welch, S.M.; Turner, W.E.; Sjödin, A.; Focant, J.-F. Cryogenic Zone Compression for the Measurement of Dioxins in Human Serum by Isotope Dilution at the Attogram Level Using Modulated Gas Chromatography Coupled to High Resolution Magnetic Sector Mass Spectrometry. J. Chromatogr. A 2011, 1218, 3274–3281. [Google Scholar] [CrossRef] [Green Version]
  12. Munch, J.W. Method 529 Determination of Explosives and Related Compounds in Drinking Water by Solid Phaseextraction and Capillary Column Gaschromatography/Mass Spectrometry (GC/MS); National Exposure Research Laboratory, Office of Research and Development, US Environmental Protection Agency: Cincinnati, OH, USA, 2002. [Google Scholar]
  13. US Environmental Protection Agency. Method 8330B Nitroaromatics, Nitramines, and Nitrate Esters by Highperformance Liquid Chroma-Tography (HPLC); US Environmental Protection Agency: Washington, DC, USA, 2006.
  14. US Environmental Protection Agency. Method 8095 Explosives by Gas Chromatography; US Environmental Protection Agency: Washington, DC, USA, 2007.
  15. Preslan, J.E.; Hatrel, B.B.; Emerson, M.; White, L.; George, W.J. An Improved Method for Analysis of 2,4,6-Trinitrotoluene and Its Metabolites from Compost and Contaminated Soils. J. Hazard. Mater. 1993, 33, 329–337. [Google Scholar] [CrossRef]
  16. Staples, E.J.; Viswanathan, S. Ultrahigh-Speed Chromatography and Virtual Chemical Sensors for Detecting Explosives and Chemical Warfare Agents. IEEE Sens. J. 2005, 5, 622–631. [Google Scholar] [CrossRef]
  17. Sigman, M.E.; Ma, C.-Y. Detection Limits for GC/MS Analysis of Organic Explosives. J. Forensic Sci. 2001, 46, 6–11. [Google Scholar] [CrossRef]
  18. Barshick, S.-A.; Griest, W.H. Trace Analysis of Explosives in Seawater Using Solid-Phase Microextraction and Gas Chroma-tography/Ion Trap Mass Spectrometry. Anal. Chem. 1998, 70, 3015–3020. [Google Scholar] [CrossRef]
  19. Gledhill, M.; Beck, A.J.; Stamer, B.; Schlosser, C.; Achterberg, E.P. Quantification of Munition Compounds in the Marine Environment by Solid Phase ExtractionUltra High Performance Liquid Chromatography with Detection by Electrospray IonisationMass Spectrometry. Talanta 2019, 200, 366–372. [Google Scholar] [CrossRef]
  20. Gordon, D.; Nawała, J.; Szala, M.; Dziedzic, D.; Dawidziuk, B.; Popiel, S. Development of Analytical Methods Used for the Study of 2,4,6-Trinitrotoluene Degradation Kinetics in Simulated Sediment Samples from the Baltic Sea. Mar. Pollut. Bull. 2018, 135, 397–410. [Google Scholar] [CrossRef]
  21. Emmrich, M.; Lahrz, T.; Spyra, W. Influence of Solvents and Gas Chromatographic Injector Conditions on the Detectability of Nitroaromatic Compounds. J. Chromatogr. A 2001, 918, 121–126. [Google Scholar] [CrossRef]
  22. Marder, D.; Tzanani, N.; Prihed, H.; Gura, S. Trace Detection of Explosives with a Unique Large Volume Injection Gas Chromatography-Mass Spectrometry (LVI-GC-MS) Method. Anal. Methods 2018, 10, 2712–2721. [Google Scholar] [CrossRef]
  23. Guidry, R.M.; Davis, L.P. Thermochemical Decomposition of Explosives. I. TNT Kinetic Parameters Determined from ESR Investigation. Thermochim. Acta 1979, 32, 1–18. [Google Scholar] [CrossRef]
  24. Ahmad, M.F.; Hussain, A.; Malik, A.Q. Thermal decomposition and kinetic evaluation of decanted 2,4,6-trinitrotoluene (TNT) for reutilization as composite material. In IOP Conference Series: Materials Science and Engineering, Proceedings of the 14th International Symposium on Advanced Materials, National Centre for Physics, Islamabad, Pakistan, 12–16 October 2015; IOP Publishing Ltd.: Bristol, UK, 2016; Volume 146, p. 012032. [Google Scholar] [CrossRef] [Green Version]
  25. Beck, A.J.; van der Lee, E.M.; Eggert, A.; Stamer, B.; Gledhill, M.; Schlosser, C.; Achterberg, E.P. In situ measurements of explosive compound dissolution fluxes from exposed munition material in the Baltic Sea. Environ. Sci. Technol. 2019, 53, 5652–5660. [Google Scholar] [CrossRef]
  26. Kampmeier, M.; Greinert, J.; Strehse, J.; Beck, A.J.; Wichert, U.; Diller, N.; Kurbjuhn, T.; Wenzlaff, E.; Schröder, J. RV Poseidon POS530Cruise Report “MineMoni 2018”. Available online: https://oceanrep.geomar.de/47567/1/CruiseReport_POS530_v05_final.pdf (accessed on 26 February 2021).
  27. Greinert, J.; Appel, D.; Beck, A.; Eggert, A.; Gräwe, U.; Kampmeier, M.; Martin, H.-J.; Maser, E.; Schlosser, C.; Song, Y.; et al. Practical Guide for Environmental Monitoring of Conventional Munitions in the Seas. Results from the BMBF Funded Pro-ject UDEMM “Umweltmonitoring Für Die Delaboration von Munition Im Meer”; GEOMAR Report, N. Ser. 054; GEOMAR Helmholtz Centre for Ocean Research: Kiel, Germany, 2019. [Google Scholar]
  28. Bae, B.; Autenrieth, R.; Bonner, J.S. Baseline separation of 2,4,6-Trinitrotoluene (TNT) and its Biotrans-Formation products using HPLC: Precautions for analytes loss. Environ. Eng. Res. 1999, 4, 135–142. [Google Scholar]
  29. European Commission, Joint Research Centre. Guidance Document on the Estimation of LOD and LOQ for Measurements in the Field of Contaminants in Feed and Food; Publications Office of the EU: Luxembourg, 2016. [Google Scholar]
  30. Dawidziuk, B.; Nawała, J.; Dziedzic, D.; Gordon, D.; Popiel, S. Development, Validation and Comparison of Three Methods of Sample Preparation Used for Identification and Quantification of 2,4,6-Trinitrotoluene and Products of Its Degradation in Sediments by GC-MS/MS. Anal. Methods 2018, 10, 5188–5196. [Google Scholar] [CrossRef]
  31. Kirchner, M.; Matisová, E.; Hrouzková, S.; Húšková, R. Fast GC and GC-MS analysis of explosives. Petroleum Coal 2007, 49, 2–79. [Google Scholar]
Figure 1. Chromatograms of the calibration standards used to determine the limits of detection (LODs) of the (a) splitless quartz wool (b) splitless CarboFrit and (c) programmable temperature vaporization—large volume injection methods. Peaks are 1: 1,3-dinitrobenzene (1,3-DNB); 2: 2,4-dinitrotoluene (2,4-DNT); 3: TNT; 4: 4-amino-2,6-dinitrotoluene (4-ADNT); 5: 2-amino-2,4-dinitrotoluene (2-ADNT).
Figure 1. Chromatograms of the calibration standards used to determine the limits of detection (LODs) of the (a) splitless quartz wool (b) splitless CarboFrit and (c) programmable temperature vaporization—large volume injection methods. Peaks are 1: 1,3-dinitrobenzene (1,3-DNB); 2: 2,4-dinitrotoluene (2,4-DNT); 3: TNT; 4: 4-amino-2,6-dinitrotoluene (4-ADNT); 5: 2-amino-2,4-dinitrotoluene (2-ADNT).
Toxics 09 00060 g001
Figure 2. Temperature optimization for splitless injection using (a) packed quartz wool and (b) CarboFrit injection port liners. The optimum temperature was determined to be 230 °C for the quartz wool and 270 °C for the CarboFrit liner.
Figure 2. Temperature optimization for splitless injection using (a) packed quartz wool and (b) CarboFrit injection port liners. The optimum temperature was determined to be 230 °C for the quartz wool and 270 °C for the CarboFrit liner.
Toxics 09 00060 g002
Figure 3. (a) Process efficiency (PE; n = 6), matrix effect (ME; n = 6), and recovery efficiency (RE, n = 2) of 10 ng of the mentioned explosives by SPE-Extraction with unconditioned Chromabond Easy columns. (b) Process efficiency of different column conditions. No major advantages were found compared to the unconditioned ones.
Figure 3. (a) Process efficiency (PE; n = 6), matrix effect (ME; n = 6), and recovery efficiency (RE, n = 2) of 10 ng of the mentioned explosives by SPE-Extraction with unconditioned Chromabond Easy columns. (b) Process efficiency of different column conditions. No major advantages were found compared to the unconditioned ones.
Toxics 09 00060 g003
Figure 4. Comparison of the same sediment sample once processed with 2 g freeze-dried material and once with 100 g wet sediment with a 0.5 ng/mL standard. While no explosives were found in the lyophilized sample, 0.6 ng TNT (1), 0.3 ng 4-ADNT (2), and 0.5 ng 2-ADNT (3) were detected in the wet one.
Figure 4. Comparison of the same sediment sample once processed with 2 g freeze-dried material and once with 100 g wet sediment with a 0.5 ng/mL standard. While no explosives were found in the lyophilized sample, 0.6 ng TNT (1), 0.3 ng 4-ADNT (2), and 0.5 ng 2-ADNT (3) were detected in the wet one.
Toxics 09 00060 g004
Figure 5. Course of the peak area of an external standard of (a) 10 ng/mL injected after every 16 measurements for a batch of 220 mussel samples prepared according to Strehse et al. 2017 and measured by splitless injection, and (b) 1 ng/mL 50 freeze-dried/SPE extracted samples measured by PTV-LVI. The intensity of TNT decreased by 50% (splitless) and 90% (PTV-LVI) during measurements, while the intensities of the other explosives increased slightly after the first measurements and then remained at the same level. For the splitless method, 13C15N-TNT was used as an internal standard to correct the area of TNT.
Figure 5. Course of the peak area of an external standard of (a) 10 ng/mL injected after every 16 measurements for a batch of 220 mussel samples prepared according to Strehse et al. 2017 and measured by splitless injection, and (b) 1 ng/mL 50 freeze-dried/SPE extracted samples measured by PTV-LVI. The intensity of TNT decreased by 50% (splitless) and 90% (PTV-LVI) during measurements, while the intensities of the other explosives increased slightly after the first measurements and then remained at the same level. For the splitless method, 13C15N-TNT was used as an internal standard to correct the area of TNT.
Toxics 09 00060 g005
Table 1. GC-MS/MS programs for splitless and large volume injections.
Table 1. GC-MS/MS programs for splitless and large volume injections.
ParameterSplitlessLarge Volume Injection
InjectorSplit-/splitlessProgrammable temp. vaporization
Inlet linerQuartz woolCarboFritQuartz wool
Injection volume1 µL5 µL
Injection temperature230 °C270 °C70 °C, (0.18 min, 50 mL × min−1)
5 °C/s to 240 °C (1.5 min, no split)
240 °C (5 min, 200 mL/min−1)
Column flow1.5 mL × min−11.2 mL × min−1
Oven temp.100 °C (0.20 min), 30 °C/min to 220 °C (0.30 min), 80 °C to 280 °C (1 min) 100 °C (1 min), 35 °C/min to 220 °C (0.7 min), 70 °C to 280 °C (1 min)
Total run time6.25 min6.99 min
Transfer line temp.250 °C
Ion source temp.300 °C
Ionization methodEI
Table 2. Retention times for the splitless (Rt SL) and programmable temperature vaporization (PTV)-large volume injection (Rt LVI) methods; quantitative (Q) and qualitative (q) secondary reaction monitoring transitions (m/z) of explosives and internal standard 13C15N-2,4,6-trinitrotoluene (TNT).
Table 2. Retention times for the splitless (Rt SL) and programmable temperature vaporization (PTV)-large volume injection (Rt LVI) methods; quantitative (Q) and qualitative (q) secondary reaction monitoring transitions (m/z) of explosives and internal standard 13C15N-2,4,6-trinitrotoluene (TNT).
CompoundRt SL [min]Rt LVI
[min]
Molecular Mass
[g × mol−1]
Transition
[m/z]
CE [eV]
1,3-Dinitrobenzene2.433.20168.11Q122.0 > 75.012
q168.0 > 75.020
q168.0 > 122.08
2,4-Dinitrotoluene2.773.52182.13Q165.0 > 63.122
q165.0 > 90.116
q165.0 > 118.18
Trinitrotoluene3.414.09227.13Q210.0 > 164.16
q164.0 > 90.110
q108.0 > 76.112
13C15N-Trinitrotoluene3.414.09237.06Q220.1 > 173.16
q220.1 > 203.18
q189.1 > 82.110
4-Amino-2,6-dinitrotoluene4.224.85197.15Q197.0 > 180.16
q180.0 > 163.18
q163.0 > 78.014
2-Amino-4,6-dinitrotoluene4.425.07197.15Q197.0 > 180.16
q180.0 > 133.06
q180.0 > 67.012
Table 3. Detection and quantification limits of the applied methods. On column, volumes are 1 µL for the splitless and 5 µL for the PTV large-volume method.
Table 3. Detection and quantification limits of the applied methods. On column, volumes are 1 µL for the splitless and 5 µL for the PTV large-volume method.
CompoundSL QWSplitless, CarboFrit LinerPTV-LVI
LOD LOQR2LOD LOQR2LOD LOQR2
fg/µLfg/µLfg/µL
1,3-DNB33310990.944433010890.9664321050.9644
2,4-DNT772540.9968862840.995110330.9934
TNT1525020.98791504950.9852471550.9878
4-ADNT953140.9951882890.98968260.9959
2-ADNT1033410.9943602100.994411370.9919
Table 4. Matrix-specific limits of detection of the methods developed for water, sediment, and mussel samples.
Table 4. Matrix-specific limits of detection of the methods developed for water, sediment, and mussel samples.
CompoundWaterSedimentMussels by Strehse et al. 2017 [3]Freeze Dried Mussels by Solid Phase Extraction
SL QWPTV LVI
LOD LOQ
ng/L
R2LOD LOQ
ng/g d.w.
R2LOD LOQ
ng/g w.w.
R2LOD LOQ
ng/g d.w.
R2LOD LOQ
ng/g d.w.
R2
1,3DNB0.200.660.9780.100.330.9442.27.20.9750.270.880.9770.030.100.985
2,4DNT0.050.150.9980.020.080.9962.27.30.9750.230.750.9830.040.120.990
TNT0.090.300.9810.050.150.9883.511.50.9400.471.600.9640.200.680.986
4ADNT0.060.190.9940.030.090.9951.55.10.9870.270.900.9880.050.170.973
2ADNT0.060.200.9920.030.100.9941.24.00.9920.100.320.9990.040.140.980
Table 5. Comparison of the instrumental detection limits (pg/µL) achieved in this study with those published by other authors.
Table 5. Comparison of the instrumental detection limits (pg/µL) achieved in this study with those published by other authors.
Present StudyGledhill et al.
2019 [19]
Gordon et al.
2018 [20]
Dawidziuk et al.
2018 [30]
Kirchner et al.
2007 [31]
MethodSL QWPTV LVILC-OrbitrapGC-MS/MSGC-MS/MSGC-MS
pg/µL
1,3-DNB0.3330.0320.153.64.8
2,4-DNT0.0770.0101.052.74.30.063
TNT0.1520.0470.036560.419.90.029
4-ADNT0.0950.0080.05047
2-ADNT0.1030.0110.03013.1
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Bünning, T.H.; Strehse, J.S.; Hollmann, A.C.; Bötticher, T.; Maser, E. A Toolbox for the Determination of Nitroaromatic Explosives in Marine Water, Sediment, and Biota Samples on Femtogram Levels by GC-MS/MS. Toxics 2021, 9, 60. https://0-doi-org.brum.beds.ac.uk/10.3390/toxics9030060

AMA Style

Bünning TH, Strehse JS, Hollmann AC, Bötticher T, Maser E. A Toolbox for the Determination of Nitroaromatic Explosives in Marine Water, Sediment, and Biota Samples on Femtogram Levels by GC-MS/MS. Toxics. 2021; 9(3):60. https://0-doi-org.brum.beds.ac.uk/10.3390/toxics9030060

Chicago/Turabian Style

Bünning, Tobias Hartwig, Jennifer Susanne Strehse, Ann Christin Hollmann, Tom Bötticher, and Edmund Maser. 2021. "A Toolbox for the Determination of Nitroaromatic Explosives in Marine Water, Sediment, and Biota Samples on Femtogram Levels by GC-MS/MS" Toxics 9, no. 3: 60. https://0-doi-org.brum.beds.ac.uk/10.3390/toxics9030060

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop