Quantum Beam Sci., Volume 5, Issue 4 (December 2021) – 7 articles

In this research, a finite element (FE) technique was used to predict the residual stresses in laser-peened aluminum 5083 at different power densities. A dynamic pressure profile was used to create the pressure wave in an explicit model, and the stress results were extracted once the solution was stabilized. It is shown that as power density increases from 0.5 to 4 GW/cm², the induced residual stresses develop monotonically deeper from 0.42 to 1.40 mm. However, with an increase in the power density, the maximum magnitude of the sub-surface stresses increases only up to a certain threshold (1 GW/cm² for aluminum 5083). Above this threshold, a complex interaction of the elastic and plastic waves occurring at peak pressures above ≈2.5 Hugoniot Elastic Limit (HEL) results in decreased surface stresses. The FE results are corroborated with physical experiments and observations. Full article

This work concerns neutron doses associated with the use of a Siemens Primus M5497 electron accelerator, which is operated in the photon mode at 15 MV. The conditions offer a situation within which a fraction of the bremsstrahlung emission energies exceed the photoneutron threshold. For different field sizes, an investigation has been made of neutron dose equivalent values at various measurement locations, including: (i) At the treatment table, at a source-surface distance of 100 cm; (ii) at the level of the floor directly adjacent to the treatment table; and (iii) in the control room and patient waiting area. The evaluated neutron dose equivalent was found to range from 0.0001 to 8.6 mSv/h, notably with the greatest value at the level of the floor directly adjacent to the treatment couch (8.6 mSv/h) exceeding the greatest value on the treatment table (5.5 mSv/h). Low values ranging from unobservable to between 0.0001 to 0.0002 mSv/h neutron dose were recorded around the control room and patient waiting area. For measurements on the floor, the study showed the dose equivalent to be greatest with the jaws closed. These data, most particularly concerning neutron distribution within the treatment room, are of great importance in making steps towards improving patient safety via the provision of protective measures. Full article

The nanopore formation process that occurs by supplying a thermal spike to single crystal CeO₂ has been simulated using a molecular dynamics method. As the initial condition, high thermal energy was supplied to the atoms in a nano-cylinder placed at the center of a fluorite structure. A nanopore was generated abruptly at around 0.3 ps after the irradiation, grew to its maximum size at 0.5 ps, shrank during the time to 1.0 ps, and finally equilibrated. The nanopore size increased with increasing effective stopping power gSe (i.e., the thermal energy deposited per unit length in the specimen), but it became saturated when gSe was 0.8 keV/nm or more. This finding will provide useful information for precise control of the size of nanopores. Our simulation confirmed nanopore formation found in the actual experiment, irradiation of CeO₂ with swift heavy ions, but could not reproduce crystalline hillock formation just above the nanopores. Full article

Recent studies have shown that the presence of dissolved salts in water can exhibit peculiar flow boiling and two-phase flow regimes. Two-phase flow and convective flow boiling are typically characterized with the help of void fraction measurements. To quantitatively improve our understanding of two-phase flow and boiling phenomenon with seawater coolant, void fraction data are needed, which can not be obtained from optical imaging. In this paper, we present experimental void fraction measurements of saturated flow boiling of tap water and seawater using X-ray radiography. X-rays with a maximum energy level of 40 KeV were used for imaging the exit region of the heated test section. At lower heat flux levels, the two phase flow in seawater was bubbly and homogeneous in nature, resulting in higher void fractions as compared to tap water. With an increase in heat flux, the flow regime was similar to slug flow, and void fraction measurements approached similarity with tap water. The predicted pressure drop using the measured void faction shows good agreement with the measured total pressure drop across the test section, demonstrating the validity of the measurement process. Full article

It has been known that the modification of non-metallic solid materials (oxides, nitrides, etc.), e.g., the formation of tracks, sputtering representing atomic displacement near the surface and lattice disordering are induced by electronic excitation under high-energy ion impact. We have investigated lattice disordering by the X-ray diffraction (XRD) of SiO₂, ZnO, Fe₂O₃ and TiN films and have also measured the sputtering yields of TiN for a comparison of lattice disordering with sputtering. We find that both the degradation of the XRD intensity per unit ion fluence and the sputtering yields follow the power-law of the electronic stopping power and that these exponents are larger than unity. The exponents for the XRD degradation and sputtering are found to be comparable. These results imply that similar mechanisms are responsible for the lattice disordering and electronic sputtering. A mechanism of electron–lattice coupling, i.e., the energy transfer from the electronic system into the lattice, is discussed based on a crude estimation of atomic displacement due to Coulomb repulsion during the short neutralization time (~fs) in the ionized region. The bandgap scheme or exciton model is examined. Full article

Amorphous selenium (a-Se) is a glass-former capable of deposition at high rates by thermal evaporation over a large area. It was chosen as a direct conversion material due to its appealing properties for imaging in both low and high X-ray energy ranges (<30 keV and <30 keV, respectively). It has a bandgap of 2.2 eV and can achieve high photodetection efficiency at short wavelengths less than 400 nm which makes it appealing for indirect conversion detectors. The integration of a-Se with readout integrated circuits started with thin-film transistors for digital flat panel X-ray detectors. With increasing applications in life science, biomedical imaging, X-ray imaging, high energy physics, and industrial imaging that require high spatial resolution, the integration of a-Se and CMOS is one direct way to improve the high-contrast visualization and high-frequency response. Over the past decade, significant improvements in a-Se/CMOS technologies have been achieved with improvements to modulation transfer function and detective quantum efficiency. We summarize recent advances in integrating and photon-counting detectors based on a-Se coupled with CMOS readout and discuss some of the shortcomings in the detector structure, such as low charge conversion efficiency at low electric field and high dark current at high electric field. Different pixel architectures and their performance will be highlighted. Full article

Scanning transmission X-ray microscopy (STXM) was utilized for analysing the bioremediation of Cr(VI) by Citrobacter freundii, a species of gram-negative bacteria. The biosorption and bioreduction processes were analysed by the chemical mapping of cells biosorbed at different concentrations of Cr(VI). STXM spectromicroscopy images were recorded at O K-edge and Cr L-edge. A thorough analysis of the X-ray absorption features corresponding to different oxidation states of Cr in the biosorbed cell indicated the coexistence of Cr(III) and Cr(VI) at higher concentrations. This signifies the presence of partially reduced Cr(VI) in addition to biosorbed Cr(VI). In addition, the Cr(III) signal is intense compared with Cr(VI) at different regions of the cell indicating excess of reduced Cr. Speciation of adsorbed Cr was analysed for the spectral features of biosorbed cell and comparison with Cr standards. Analysis of absorption onset, L3/L2 ratio and absorption fine structure concludes that adsorbed Cr is predominantly present as Cr(III) hydroxide or oxyhydroxide. The evolution of absorption features in the duration of biosorption process was also studied. These time lapse studies depict the gradual decrement in Cr(VI) signal as biosorption proceeds. A strong evidence of interaction of Cr with the cell material was also observed. The obtained results provide insights into the biosorption process and chemical speciation of Cr on the cells. Full article