1. Introduction
Minimization of reflectance of an input (output) facet of a light-guide is our study’s primary task. While also providing a small enough angular divergence of the forward scattered beam, we get the maximal transmittance—the light-guide designers’ main trouble. Therefore, we demonstrate the results based on the transmittance characteristics. Engraving a facet was chosen as the means allowing for solving the problem in a broad wavelength spectrum. To design the surface engraved structure providing minimal reflection, we developed the proper physical model in the previous stage [
1]. This model is based on the variations calculus and allows predicting the required shape of engraving, providing minimal reflection. This considered structure (in that study and here as well) is formed by pins on a plane facet (the pins can be replaced by similarly shaped indentations) made from the same matter as the light-guide itself. The model deals with infinite size layered structures with dielectric parameters calculated according to the Maxwell–Garnett approximation (e.g., [
2]). The analysis was given in the frame of the single scattering (Born’s) approximation. The obtained result require the pins to be elements possessing a constant slope, i.e., cones or pyramids. The theoretically required slope angle depends only on the refraction index of the light-guide medium. The study in [
1] concerns only conically shaped pins and indentations. The existence of multiple scattering leads to the necessity of smoothing cones to paraboloids (in the literature, other different shapes are discussed without preliminary justification [
3], which are indeed hardly achievable). The authors of [
1] also noted that maximization of the facets’ fill-factor is not less important, and thus (smoothed) pyramidal structures promise to be more efficient.
With the right choice of the conical unit-cells (pins or indentations) and structure parameters (as their height and diameter), one can get the transmission of a small size facet a little more than 98% and the flatness in the given wavelength range as 1% (and it is especially desirable to reduce just this parameter).
Another aspect widely discussed in the literature is the randomization of an anti-reflection (AR) structure. We have to note that the positive effect of this procedure was not confirmed up today by reliable results and conclusions [
3,
4,
5,
6,
7]. Our remarks concerning the fill-factor suggest height-randomization of the pins (but not the bottom size and position) in the structure to get possibly a higher and more uniform transmission for the broadband spectrum. However, they are only preliminary expectations. We tested all these states numerically in the present study.
One can evaluate the anti-reflection efficiency of a surface structure from two different criteria.
The first evaluation can be done for the structure itself, while used in the ideal condition: it is an engraved infinite surface illuminated by a plane wave.
Such structures can be approximated by a multilayered configuration that describes a layer with a gradient index when the number of layers tends to infinity. The rigorous theoretical analysis of this structure’s response is given in
Appendix A.
Another evaluation (more relevant for different applications) can be done for an actual facet of a particular shape and a finite square. With this, one has to pay attention to the geometrical parameters. In practical cases, we deal with a given size facet, illuminated by a specific beam. Therefore, a part of the energy can avoid the structured surface. Thus, it contributes to the extra-reflection measured in the experiment.
Moreover, dealing with a nano-structured facet of a light-guide and using the chosen wavelength, we often cannot minimize the size of the focal spot of the input beam. We did not provide this analysis in the previous publication, taking into consideration only the part of the beam power which hits the facet. Reducing the edge effect requires additional means. The problem is analogous to one of reducing side-lobes of a beam diffracted by a hole. This is the old problem of classical optics. One of the conventional means, resolving it for a circular hole, is in using Gaussian beams. The proper illustration given below is imported (and restored) from [
8].
The graphs in this
Figure 1 demonstrate that the Gaussian beam provides a concentration of diffracted energy in the main lob while reducing the energy diffracted to the side lobes. We can probe such a solution in our case as well. It means using the apodization of the whole structure. However, the simplified calculations (see
Appendix B) show that:
- -
The angular distribution of the diffracted beam occurs to be partly smoothed by the pins’ parabolic shape, but not by an edge apodization.
- -
A large enough critical angle for total internal reflection (TIR) in our case (light-guide material) allows collecting all forth-scattering peaks. Thus, the edge effect is not significant at all.
- -
Apodization, in turn, leads to redistribution of the beam energy in favor of the side lobes. This effect will increase the losses by those lobes, for which the TIR condition will be broken.
Summarizing, we state that the considered structures do not require any correction for diminishing the edge effects.
Recall that the additional requirement complicated our general task (as in the previous stage too). We took it upon ourselves to meet the above criteria for a light-guide, which a high optical contrast with its surroundings. In our study, we deal with Si light-guide, which is transparent in our wavelength range and provides the transmission about 82% for a wide enough polished surface.
We note that all the results below were obtained by numerical calculations fulfilled by the commercial simulator “Lumerical”, which uses the FDTD method. The numerical simulations were performed for the given size facet. “Lumerical” solves the Maxwell equations numerically under the boundary conditions determined by the facet and the light-guide itself. The multiple scattering is taken into account automatically. Thus, we dependably estimated the advantages of pins smoothing.
2. Parabolic Smoothing
As discussed in the previous section, the multiple scattering contribution forces us to modify the conical shape of the unit cells obtained by solving the variational reflection minimization problem. For a discussion of the multiple scattering effect contribution, see, for example, Simonetti and Garnett in [
9,
10,
11]. Our previous publication shows that an effective modification is using a paraboloid shape instead of the proper cone. Here, we test the efficiency of smoothing pyramidal unit-cells.
The advantage of parabolic smoothing is obtaining the surface smooth also with respect to its derivatives (a higher order of smoothness).
It is necessary to note that this recommendation cannot be accepted as the general one, equally efficient for any shape of the cross-section. Numerical tests are required for any specific configuration of the cross-section. However, the main conclusion can be made: smoothing leads to a better flatness of transmission characteristic as the function of the wavelength. It is already seen in Figure 5 of [
1] (in a sense, it is appropriate to point to Chebyshev-type fillers as an analogy (see, e.g., [
12])). The smoothing efficiency is tested here for round, square, rectangular, and hexagonal basis of unit-cells (pins).
3. Height Randomization of Pins in Conic-Parabolic Structure
It is well known (see, e.g., [
3]) that one can obtain almost zero reflection for a single spectral line. Such a result is achieved without any randomization. However, any widening of the required spectral range affects the possible minimal reflection while understanding it in terms of the mean value. However, this is not yet the well-defined formulation of the goal. For a trustful evaluation of the role of randomization, one has to proceed from an explicit criterion. In the present discussion, we accept the following one:
- -
maximization of the mean value of transmission in the required spectral interval (); and
- -
minimization of the standard deviation of transmission (defined as usually: ).
Previous discussions on the effect of randomization can be found, e.g., in [
4,
5]. However, first, we have to emphasize some significant aspects.
- (a)
The true effect of randomization can only be seen for a large enough facet. Any statistics is valid only for a large number of elements (unit cells).
- (b)
The optimal structure of the whole facet has to take into account the profile of the illuminating beam.
The illumination scheme in a virtual experiment (and, namely, this illumination—of the Gaussian shape—is taken into account in our numerical calculations) is depicted in
Figure 2. In our calculations, we use our laboratory fiber laser providing 7
m diameter of the focal point and
of divergences after the focus. The Si light-guide has the aperture of 20 × 1.5
m.
We see immediately that this geometry does not respond to the requirements mentioned above. Therefore, the results presented below are not the best which could be obtained with the same pin-structure in the ideal conditions. In the previous publication, we discussed the possible effect of randomization of pins’ heights in the structure (see
Figure 3). Here, we present numerical analysis results, which show that the conclusions about the efficiency of the randomization are not straightforward.
First, we recall the results concerning the effect of the height of conic, parabolic smoothed pins on the transmittance of the facet.
Turn to the graphs depicting the transmission efficiency of the facets studded by parabolic pins (the small dimension of its aperture is 20 × 3). In the numerical calculations (here and after), we define transmission of the facet on a light-guide input (output) surface as the forward scattering in the range of angles required for the light-guide.
Here, the value of the standard deviation indicates the randomization level.
We calculated the parameters chosen as the criterion:
For nonrandom structure (
), the mean transmission is
and the standard deviation of transmission is (
). The results are given in detail in
Table 1.
We see (
Figure 4) that, for the given facet, it is not easy to conclude which one of the tested randomized structures is the best. The conclusion here is: for small apertures, randomization is not efficient. It is not a surprising result; it is already mentioned above.
.
However, some conclusions can still be made: a larger requires a larger mean value of H.
It is interesting, but the actual technology restricts a possible value of the height. For example, while using Focused Ion Beam (FIB), we face the restriction as
, where
is the base diameter of the paraboloid. For laboratory tests, one often chooses the available equipment. Today, we can use also the laser engraving [
13,
14], lithography [
15], and the most accurate nano-scribe technology [
16]. The last one is perhaps the most expensive and hardly available for Si. However, it is possibly the single one allowing to obtain the difficult to locate pins, as we require. As we estimate, lithography is more attractive for series manufacturing and hardly useful for samples gradually varying in depth. The laser methods’ advantages or disadvantages depend on the sample material and scale and the achievable diameter of the focal spot.) This fact puts an additional restriction on the ability and efficiency of randomization. Moreover, based on our results, we can state that randomization does not improve the transmission function’s flatness.
4. Pyramidal Structures
As discussed above, pyramidal pins potentially promise an increase in transparency due to improved fill-factor. We obtain the best fill-factor for rectangular (square, for specific facet shapes) pyramids. The illustrations of the structure, based on square and hexagonal pyramids, are given in
Figure 10.
The square and hexagonal shapes differ not only by the fill-factor but also by the scattering shape. Therefore, the final conclusion can be made only after accurate numerical calculations.
The pyramidal structures were considered in different studies (e.g., [
17,
18]); however, only as a case and without general conclusions. Here, we generalize the analysis that allows us to provide confident recommendations. When using rectangular facets, the main evident advantages of pyramidal structures are in increasing the fill factor. A facet composed of hexagonal pyramids retains a free area at the edges anyway. Our illustrations in
Figure 10 show this fact in the evident form. For the correct comparison of the two structures’ efficiency, we have to take their sizes more or less equivalent (we chose the criterion as equality of their heights and their bottom and upper areas). For example, where the height of the pyramid is
nm, the side of the bottom base of the square-based pyramid is
nm, and the upper square is
nm, and the same areas for the hexagon pyramids. The results are shown in
Figure 11.
For easier comparison, we give below the mean values and standard deviations of transmission for the tested pyramids (in natural units). The results given in detail in the
Table 7.
The results are slightly different, but the square pyramid is still preferred. Therefore, further, we consider only this type of pyramids.
Adopting a bottom of the pyramidal uni-cell of rectangular and not a square shape, one can achieve the fill-factor as 1. The results of the proper test are demonstrated in
Figure 12.
In terms of area, the rectangular pyramids’ base was taken equal to the bottom of the square one. However, the aspect ratio was taken to be appropriate to obtain a fill factor of 1. The results show the advantage of a regular rectangular structure. The mean transmission reaches the level as 99%.
However, the size of the rectangular base is determined by the shape of the facet; thus, it must be a specific choice every time. In order not to be limited to a particular form of the facet, in the following, we analyze mainly the square bases of the pyramids. Only one specific case was taken to assess the maximum fill factor’s influence, and it shows its importance. For this particular facet, the improving factor for the mean transmission is
, but the improvement of the standard deviation is significant (
Figure 13).
4.1. Truncated and Smoothed Rectangular Pyramids
Recall, first that, dealing with cones ([
1]), we obtained the best results for those with the bottom diameter
nm. Therefore, in further analysis, we accept the pyramids with a similar bottom area. As previously, we expect some improvement in the transmission by smoothing the pyramids. It seems natural enough to expect an impoverished scattering angular spectrum for smoother scatterers. The height of the parabolic cap (smoothing) is taken as 200 nm. The results of both cases are given in figure. The height of the parabolic cap (smoothing) is taken as 200 nm. The results of both cases are given in
Figure 13.
The smoothed surface provides an apparent improvement. The mean value of transmission achieved a value of 0.983, with a standard deviation of about 0.0014 (i.e., the smoothing of pins significantly improves the flatness). Smoothing of rectangular pyramids is more problematic; however, recalling our previous estimation, one can hope to get the mean value of transmission about
0.987. In the next short section, we show the results of randomizing the pins’ height on the facet. Another possibility, modification of the edge pins to smooth the edge effect, is discussed in
Appendix B.
4.2. Randomization of Height of the Unit-Cells in Smoothed Pyramidal Structures
In this section, we try the effect of height randomization for the pyramidal structure. The results for different
are depicted in
Figure 14.
As is seen, the randomization of pin height in the pyramidal structure works even worse than in the conical structure. Moreover, it can give even a negative effect. These results are not so surprising. In the literature, we can find an intensive discussion on the pros and cons of randomization (see, e.g., [
4]). Such results of randomization for conic structures are discussed above. Thus, we can conclude that any randomization can provide an effect (positive or negative) only for large enough facets.
A numerical analysis of a large facet is a bulky task. A gradient index model for large surfaces (described in [
1]) is to be accurate enough in their central area (where edge effects do not contribute). The model works in a range of wavelengths matched to it. Moreover, in this range, we do not indicate an essential dependence of the reflectance (transmittance) on the wavelength. Therefore, the need in randomization looks doubtful (see
Appendix B in the present work).
5. The Simple Way for Comparing Calculation and Experimental Results
Underline from the very beginning, the numerical calculation of the reflection and transmission for the wave passed through a light-guide is a very bulky problem. With this, any laboratory measurements (of reflection or transmission characteristics) deal just with a wave transmitted through a light-guide once or several times. However, there is a workaround, which allows for significantly simplifying the necessary calculations.
First, we consider a plane wave propagating through space (filled by a medium with the refractive index n) bounded by flat parallel (normal to the direction of wave propagation) boundaries. Call it a slab (despite its infinite side boundaries). Let air be its ambient medium.
Let r and t be the reflectance and transmittance, respectively, of each boundary facet and R and T the reflectance and transmittance of the whole slab. Designate the thickness of this slab as D. Let also the input wave amplitude be 1.
For the reflection from the slab (in the scalar form), we have (see, e.g., [
19])
where
.
In turn, for the transmission though this slab, we write
From this equations, we get the simple relation
Principally, measuring R and T, one can estimate the reflectance r of the facet and compare it with the calculated value. However, this task’s single problem is the accurate measurement of D (of the order as ).
On the other hand, we get similar equations while dealing not with the infinite plane but a light-guide mode (for a single-mode light-guide or the proper superposition of modes for a multi-mode one) with a single difference. Namely, the factor has to be replaced by another one (designated as ).
Thus, the factor is the single obstacle for simple experimental testing of our mathematical model.
6. Discussion and Conclusions
This study is the continuation of the previous one [
1], where we developed the semi-analytic formalism for calculating the parameters of a meta-surface made from a high-index dielectric material, similar to that used for the light-guide. Our analysis demonstrated the transparency effect also to high optical index optical light-guides (Si). Basing on the previous results, we analyzed more cumbersome structures and estimated maximal transmission while using structural surfaces (facets). We considered only those types of engraving which can be fabricated, therefore omitting shapes which can be defined by polynomial functions of higher than 2 (or even more complicated). In addition, we restricted our analysis by the height of the unit cells achievable for FIB technology, i.e.,
.
The pyramids were introduced since they satisfy our theoretical predictions and fill rectangular facets more effectively (even achieving the total fill). Despite its more complex scattering side surface (a ribbing one), numerical calculations demonstrate an improvement compared to cones. Note that hexagonal base pyramids occur less effectively than the rectangular ones. Again, the base size is determined by the required spectral range and also by the fill-factor. The hexagonal base leaves a certain unfilled edge anyway.
Smoothing the top has an essential effect for improving the transmission. In turn, the optimally tailored rectangular base improves the transmission additionally.
We showed that this configuration allows achieving 0.987 transmission level in 1–2-micron wavelength range with the flatness of about 0.2%. We note that flatness is a crucial characteristic, limited together with the mean value of the minimal transmission in the required spectral band. On the contrary, randomizing the pins’ heights does not provide a remarkable effect, and the pyramidal structure worsens the transmission. This negative effect can be explained by the small size and specific aspect ratio of the facet.
The surface smallness does not result in transmission degradation determined by the edge effects but restricts the engraving’s positive impact.
Here, and in the previous work, we provide a systematic analysis of the structures, justified theoretically in the single-scattering approximation. Improvements in transmission (reflection) and especially flatness characteristics were achieved. It is worth highlight that the effect was obtained not so much due to the shape of the pins (conical or pyramidal), but due to their smoothing and increasing the fill-factor. The shape smoothing allows for adopting the structures to the actual multi-scattering case. Moreover, the smoothed pins are easily realizable. The approach elaborated in our study is equally useful for other shapes and sizes of facets. We can claim that we obtained the best possible result for realizable facets for the considered rectangular profile with the given size.