Electricity, Volume 2, Issue 2 (June 2021) – 7 articles

This paper presents an effective solution to overcome the problem caused by intermittent energy sources that are connected to a balanced/unbalanced distribution system using a superconducting magnetic energy storage (SMES) system by mitigating the voltage and frequency fluctuations during wind gusts. The fuzzy logic control technique (FLC) is used with SMES to improve the voltage and frequency. A squirrel cage induction generator (SCIG) is applied as the wind energy generator. The IEEE 33-bus distribution system is used to validate the proposed method. Buses 18 33 are the weakest points in this system; thus, the wind and SMES systems are connected to the system at these buses. We used MATLAB/Simulink to simulate the performance of the IEEE 33-bus system (balanced/unbalanced) considering the SMES, wind system, and fuzzy logic control (FLC). The simulation results show the high performance of the proposed control method to alleviate the voltage and frequency fluctuation and achieve the power leveling strategy of the studied system. Full article

Nowadays, response to electricity consumption growth is mainly supported by efficiency; therefore, this is the new main goal in the development of electric distribution networks, which must fully comply with the system’s constraints. In recent decades, the issue of independent reactive power services, including the optimal placement of capacitors in the grid due to the restructuring of the electricity industry and the creation of a competitive electricity market, has received attention from related companies. In this context, a genetic algorithm is proposed for optimal planning of capacitor banks. A case study derived from a real network, considering the application of suitable daily profiles for loads and generators, to obtain a better representation of the electrical conditions, is discussed in the present paper. The results confirmed that some placement solutions can be obtained with a good compromise between costs and benefits; the adopted benefits are energy losses and power factor infringements, taking into account the network technical limits. The feasibility and effectiveness of the proposed algorithm for optimal placement and sizing of capacitor banks in distribution systems, with the definition of a suitable control pattern, have been proved. Full article

The introduction of series capacitors in transmission lines causes problems in terms of reliability and the security of distance protection relays. As distance protection is widely used in the transmission network, the challenge of applying it to series compensated lines has been taken up by utilities and relay manufacturers in various ways. In the field of power system protection, developments are largely driven by relay manufacturers, and are often not published in the academic literature; the status and trend of the relay manufacturer’s development are better found in their product manuals and patent activity. Further insight into specific implementations by transmission utilities can be found from publications in industry-led forums and some academic journals. This article surveys the status and development of distance protection for series compensated lines, with a focus on industrial implementation and practical considerations. Factors that influence the protection of series compensated lines are presented. Implementation examples reported by utilities are summarized as examples of the different situations encountered and the methods used to deal with them. It is observed that many utilities use communication-aided protection in series compensated lines, and distance protection is used with reduced reach. Solutions described in relay manuals are presented to demonstrate the manufacturers’ approaches to problems associated with series capacitor protection. While there are methods to counter voltage inversion, current inversion seems to represent a more serious challenge. A patent overview indicates the trends in this domain to be moving towards time-domain-based faster protection methods. Full article

Electromagnetic fields and the heat of a metal oxide varistor (MOV), in which a lightning impulse current flows, are calculated using the finite-difference time-domain (FDTD) method. The MOV is represented with small rectangular parallelepiped cells, each of which has a resistivity dependent on electric field and temperature. For this purpose, the expression of resistivity as a function of the electric field, proposed previously, is extended to include the dependence on temperature. The temperature dependence is based on voltages across an MOV for impulse currents of 0.5 to 10 kA at temperatures in a range from about 300 to 900 K, measured by Andoh et al. (2000). FDTD-calculated waveform of voltage across the MOV agrees well with the corresponding measured one for a short impulse current with a magnitude of about 4 kA and a duration of about 30 μs. In addition, the temperature on the surface of the MOV agrees well with the corresponding measured one. Further, calculations are carried out for the MOV with a nonuniform resistivity distribution, which roughly simulates deterioration or degradation of the MOV, for a long duration current having a magnitude of 5 kA. The proposed expression of resistivity, given as a function of electric field and temperature, is useful in studying electro-thermal calculations, which can provide insights into causes of MOV damages. Full article

The operation and the development of power system networks introduce new types of stability problems. The effect of the power generation and consumption on the frequency of the power system can be described as a demand/generation imbalance resulting from a sudden increase/decrease in the demand and/or generation. This paper investigates the impact of a loss of generation on the transient behaviour of the power grid frequency. A simplified power system model is proposed to examine the impact of change of the main generation system parameters (system inertia, governor droop setting, load damping constant, and the high-pressure steam turbine power fraction), on the primary frequency response in responding to the disturbance of a 1.32 GW generation loss on the UK power grid. Various rates of primary frequency responses are simulated via adjusting system parameters of the synchronous generators to enable the controlled generators providing a fast-reliable primary frequency response within 10 s after a loss of generation. It is concluded that a generation system inertia and a governor droop setting are the most dominant parameters that effect the system frequency response after a loss of generation. Therefore, for different levels of generation loss, the recovery rate will be dependent on the changes of the governor droop setting values. The proposed model offers a fundamental basis for a further investigation to be carried on how a power system will react during a secondary frequency response. Full article

The global development of high-voltage direct-current (HVDC) systems in fields such as renewable energy sources, interconnection of asynchronous grids or power transmission over great distances, is unquestionably important. Though widely used, the modular multilevel converter with half-bridge cells is sensitive to DC pole-to-pole faults and the time-response of the protections is critical. Reliability and availability are paramount: circuit-breakers must minimize the effects of any fault on the converter, while ensuring rapid restart. This paper focuses on the modelling aspects to analyse the behaviour of HVDC stations during DC pole-to-pole faults, using either AC or DC circuit-breakers, with different parameters. The proposed model can represent the main issues met by the converter cells during DC faults, such as semiconductor overcurrents and overvoltages, allowing a proper design of the cells. Full article

Due to the predicted rise of Unmanned Aircraft Systems (UAS) in commercial, civil, and military operations, there is a desire to make UASs more energy efficient so they can proliferate with ease of deployment and maximal life per charge. To address current limitations, a three-tiered approach is investigated to mitigate Unmanned Aerial Vehicle (UAV) hover time, reduce network datalink transmission to a ground station, and provide a real-time framework for Sense-and-Avoidance (SAA) target classification. An energy-efficient UAS architecture framework is presented, and a corresponding SAA prototype is developed using commercial hardware to validate the proposed architecture using an experimental methodology. The proposed architecture utilizes classical computer vision methods within the Detection Subsystem coupled with deeply learned Convolutional Neural Networks (CNN) within the Classification Subsystem. Real-time operations of three frames per second are realized enabling UAV hover time and associated energy consumption during SAA processing to be effectively eliminated. Additional energy improvements are not addressed in the scope of this work. Inference accuracy is improved by 19% over baseline COTS models and current non-adaptive, single-stage SAA architectures. Overall, by pushing SAA processing to the edge of the sensors, network offload transmissions and reductions in processing time and energy consumption are feasible and realistic in future battery-powered electric air transportation systems. Full article