Wind Turbine Aerodynamics

A special issue of Applied Sciences (ISSN 2076-3417). This special issue belongs to the section "Energy Science and Technology".

Deadline for manuscript submissions: closed (30 September 2018) | Viewed by 98207
Related Special Issue: https://0-www-mdpi-com.brum.beds.ac.uk/journal/applsci/special_issues/wind_turbine_aerodynamics_II

Printed Edition Available!
A printed edition of this Special Issue is available here.

Special Issue Editor

Department of Wind Energy, Aero and Fluid Dynamics Section, Nils Koppels Allé, Building 403, 2800 Kgs. Lyngby, Denmark
Interests: wind turbine aerodynamics; wind turbine aeroacoustics; wake modelling; wind turbine design; computational fluid dynamics; computational aero acoustics; wind farm layout optimization
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

In order to reach the goal of 100% renewable energy consumption, wind energy, as a pioneer of renewable energy, is developing very quickly all over the world. To reduce the levelized cost of energy (LCOE), the size of a single wind turbine has been increased to 10 MW nowadays and it will increase further in the near future. Big wind turbines and their associated wind farms have many challenges in aerodynamics, aero-elasticity and aeroacoustics. The typical effects are mainly related to the increase in Reynolds number and blade flexibility. This Special Issue collects some important works addressing the aerodynamic challenges to help scientifically the realization of such development.

Prof. Wen Zhong Shen
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Applied Sciences is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2400 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • Wind turbine
  • Wind farm
  • Aerodynamics
  • Aero-elasticity
  • Aeroacoustics
  • Fluid-structure interaction

Published Papers (22 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Editorial

Jump to: Research

4 pages, 161 KiB  
Editorial
Special Issue on Wind Turbine Aerodynamics
by Wen Zhong Shen
Appl. Sci. 2019, 9(9), 1725; https://0-doi-org.brum.beds.ac.uk/10.3390/app9091725 - 26 Apr 2019
Cited by 4 | Viewed by 2062
Abstract
In order to reach the goal of 100% renewable energy in energy systems, wind energy, as a pioneer of renewable energy, is developing very quickly all over the world [...] Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)

Research

Jump to: Editorial

22 pages, 9651 KiB  
Article
Development of an Efficient Numerical Method for Wind Turbine Flow, Sound Generation, and Propagation under Multi-Wake Conditions
by Zhenye Sun, Wei Jun Zhu, Wen Zhong Shen, Emre Barlas, Jens Nørkær Sørensen, Jiufa Cao and Hua Yang
Appl. Sci. 2019, 9(1), 100; https://0-doi-org.brum.beds.ac.uk/10.3390/app9010100 - 28 Dec 2018
Cited by 3 | Viewed by 2900
Abstract
The propagation of aerodynamic noise from multi-wind turbines is studied. An efficient hybrid method is developed to jointly predict the aerodynamic and aeroacoustics performances of wind turbines, such as blade loading, rotor power, rotor aerodynamic noise sources, and propagation of noise. This numerical [...] Read more.
The propagation of aerodynamic noise from multi-wind turbines is studied. An efficient hybrid method is developed to jointly predict the aerodynamic and aeroacoustics performances of wind turbines, such as blade loading, rotor power, rotor aerodynamic noise sources, and propagation of noise. This numerical method combined the simulations of wind turbine flow, noise source and its propagation which is solved for long propagation path and under complex flow environment. The results from computational fluid dynamics (CFD) calculations not only provide wind turbine power and thrust information, but also provide detailed wake flow. The wake flow is computed with a 2D actuator disc (AD) method that is based on the axisymmetric flow assumption. The relative inflow velocity and angle of attack (AOA) of each blade element form input data to the noise source model. The noise source is also the initial condition for the wave equation that solves long distance noise propagation in frequency domain. Simulations were conducted under different atmospheric conditions which showed that wake flow is an important part that has to be included in wind turbine noise propagation. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

15 pages, 2093 KiB  
Article
Comparison of the Blade Element Momentum Theory with Computational Fluid Dynamics for Wind Turbine Simulations in Turbulent Inflow
by Sebastian Ehrich, Carl Michael Schwarz, Hamid Rahimi, Bernhard Stoevesandt and Joachim Peinke
Appl. Sci. 2018, 8(12), 2513; https://0-doi-org.brum.beds.ac.uk/10.3390/app8122513 - 06 Dec 2018
Cited by 11 | Viewed by 3712
Abstract
In this work three different numerical methods are used to simulate a multi-megawatt class class wind turbine under turbulent inflow conditions. These methods are a blade resolved Computational Fluid Dynamics (CFD) simulation, an actuator line based CFD simulation and a Blade Element Momentum [...] Read more.
In this work three different numerical methods are used to simulate a multi-megawatt class class wind turbine under turbulent inflow conditions. These methods are a blade resolved Computational Fluid Dynamics (CFD) simulation, an actuator line based CFD simulation and a Blade Element Momentum (BEM) approach with wind fields extracted from an empty CFD domain. For all three methods sectional and integral forces are investigated in terms of mean, standard deviation, power spectral density and fatigue loads. It is shown that the average axial and tangential forces are very similar in the mid span, but differ a lot near the root and tip, which is connected with smaller values for thrust and torque. The standard deviations in the sectional forces due to the turbulent wind fields are much higher almost everywhere for BEM than for the other two methods which leads to higher standard deviations in integral forces. The difference in the power spectral densities of sectional forces of all three methods depends highly on the radial position. However, the integral densities are in good agreement in the low frequency range for all methods. It is shown that the differences in the standard deviation between BEM and the CFD methods mainly stem from this part of the spectrum. Strong deviations are observed from 1.5 Hz onward. The fatigue loads of torque for the CFD based methods differ by only 0.4%, but BEM leads to a difference of up to 16%. For the thrust the BEM simulation results deviate by even 29% and the actuator line by 7% from the blade resolved case. An indication for a linear relation between standard deviation and fatigue loads for sectional as well as integral quantities is found. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

18 pages, 5357 KiB  
Article
A Fully Coupled Computational Fluid Dynamics Method for Analysis of Semi-Submersible Floating Offshore Wind Turbines Under Wind-Wave Excitation Conditions Based on OC5 Data
by Yin Zhang and Bumsuk Kim
Appl. Sci. 2018, 8(11), 2314; https://0-doi-org.brum.beds.ac.uk/10.3390/app8112314 - 20 Nov 2018
Cited by 36 | Viewed by 8186
Abstract
Accurate prediction of the time-dependent system dynamic responses of floating offshore wind turbines (FOWTs) under aero-hydro-coupled conditions is a challenge. This paper presents a numerical modeling tool using commercial computational fluid dynamics software, STAR-CCM+(V12.02.010), to perform a fully coupled dynamic analysis of the [...] Read more.
Accurate prediction of the time-dependent system dynamic responses of floating offshore wind turbines (FOWTs) under aero-hydro-coupled conditions is a challenge. This paper presents a numerical modeling tool using commercial computational fluid dynamics software, STAR-CCM+(V12.02.010), to perform a fully coupled dynamic analysis of the DeepCwind semi-submersible floating platform with the National Renewable Engineering Lab (NREL) 5-MW baseline wind turbine model under combined wind–wave excitation environment conditions. Free-decay tests for rigid-body degrees of freedom (DOF) in still water and hydrodynamic tests for a regular wave are performed to validate the numerical model by inputting gross system parameters supported in the Offshore Code Comparison, Collaboration, Continued, with Correlations (OC5) project. A full-configuration FOWT simulation, with the simultaneous motion of the rotating blade due to 6-DOF platform dynamics, was performed. A relatively heavy load on the hub and blade was observed for the FOWT compared with the onshore wind turbine, leading to a 7.8% increase in the thrust curve; a 10% decrease in the power curve was also observed for the floating-type turbines, which could be attributed to the smaller project area and relative wind speed required for the rotor to receive wind power when the platform pitches. Finally, the tower-blade interference effects, blade-tip vortices, turbulent wakes, and shedding vortices in the fluid domain with relatively complex unsteady flow conditions were observed and investigated in detail. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

17 pages, 5494 KiB  
Article
Design and Testing of a LUT Airfoil for Straight-Bladed Vertical Axis Wind Turbines
by Shoutu Li, Ye Li, Congxin Yang, Xuyao Zhang, Qing Wang, Deshun Li, Wei Zhong and Tongguang Wang
Appl. Sci. 2018, 8(11), 2266; https://0-doi-org.brum.beds.ac.uk/10.3390/app8112266 - 16 Nov 2018
Cited by 12 | Viewed by 5572
Abstract
The airfoil plays an important role in improving the performance of wind turbines. However, there is less research dedicated to the airfoils for Vertical Axis Wind Turbines (VAWTs) compared to the research on Horizontal Axis Wind Turbines (HAWTs). With the objective of maximizing [...] Read more.
The airfoil plays an important role in improving the performance of wind turbines. However, there is less research dedicated to the airfoils for Vertical Axis Wind Turbines (VAWTs) compared to the research on Horizontal Axis Wind Turbines (HAWTs). With the objective of maximizing the aerodynamic performance of the airfoil by optimizing its geometrical parameters and by considering the law of motion of VAWTs, a new airfoil, designated the LUT airfoil (Lanzhou University of Technology), was designed for lift-driven VAWTs by employing the sequential quadratic programming optimization method. Afterwards, the pressure on the surface of the airfoil and the flow velocity were measured in steady conditions by employing wind tunnel experiments and particle image velocimetry technology. Then, the distribution of the pressure coefficient and aerodynamic loads were analyzed for the LUT airfoil under free transition. The results show that the LUT airfoil has a moderate thickness (20.77%) and moderate camber (1.11%). Moreover, compared to the airfoils commonly used for VAWTs, the LUT airfoil, with a wide drag bucket and gentle stall performance, achieves a higher maximum lift coefficient and lift–drag ratios at the Reynolds numbers 3 × 105 and 5 × 105. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

18 pages, 5922 KiB  
Article
An Optimization Framework for Wind Farm Design in Complex Terrain
by Ju Feng, Wen Zhong Shen and Ye Li
Appl. Sci. 2018, 8(11), 2053; https://0-doi-org.brum.beds.ac.uk/10.3390/app8112053 - 25 Oct 2018
Cited by 34 | Viewed by 3602
Abstract
Designing wind farms in complex terrain is an important task, especially for countries with a large portion of complex terrain territory. To tackle this task, an optimization framework is developed in this study, which combines the solution from a wind resource assessment tool, [...] Read more.
Designing wind farms in complex terrain is an important task, especially for countries with a large portion of complex terrain territory. To tackle this task, an optimization framework is developed in this study, which combines the solution from a wind resource assessment tool, an engineering wake model adapted for complex terrain, and an advanced wind farm layout optimization algorithm. Various realistic constraints are modelled and considered, such as the inclusive and exclusive boundaries, minimal distances between turbines, and specific requirements on wind resource and terrain conditions. The default objective function in this framework is the total net annual energy production (AEP) of the wind farm, and the Random Search algorithm is employed to solve the optimization problem. A new algorithm called Heuristic Fill is also developed in this study to find good initial layouts for optimizing wind farms in complex terrain. The ability of the framework is demonstrated in a case study based on a real wind farm with 25 turbines in complex terrain. Results show that the framework can find a better design, with 2.70% higher net AEP than the original design, while keeping the occupied area and minimal distance between turbines at the same level. Comparison with two popular algorithms (Particle Swarm Optimization and Genetic Algorithm) also shows the superiority of the Random Search algorithm. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

19 pages, 7166 KiB  
Article
Condition Monitoring of Wind Turbine Blades Using Active and Passive Thermography
by Hadi Sanati, David Wood and Qiao Sun
Appl. Sci. 2018, 8(10), 2004; https://0-doi-org.brum.beds.ac.uk/10.3390/app8102004 - 22 Oct 2018
Cited by 39 | Viewed by 5048
Abstract
The failure of wind turbine blades is a major concern in the wind power industry due to the resulting high cost. It is, therefore, crucial to develop methods to monitor the integrity of wind turbine blades. Different methods are available to detect subsurface [...] Read more.
The failure of wind turbine blades is a major concern in the wind power industry due to the resulting high cost. It is, therefore, crucial to develop methods to monitor the integrity of wind turbine blades. Different methods are available to detect subsurface damage but most require close proximity between the sensor and the blade. Thermography, as a non-contact method, may avoid this problem. Both passive and active pulsed and step heating and cooling thermography techniques were investigated for different purposes. A section of a severely damaged blade and a small “plate” cut from the undamaged laminate section of the blade with holes of varying diameter and depth drilled from the rear to provide “known” defects were monitored. The raw thermal images captured by both active and passive thermography demonstrated that image processing was required to improve the quality of the thermal data. Different image processing algorithms were used to increase the thermal contrasts of subsurface defects in thermal images obtained by active thermography. A method called “Step Phase and Amplitude Thermography”, which applies a transform-based algorithm to step heating and cooling data was used. This method was also applied, for the first time, to the passive thermography results. The outcomes of the image processing on both active and passive thermography indicated that the techniques employed could considerably increase the quality of the images and the visibility of internal defects. The signal-to-noise ratio of raw and processed images was calculated to quantitatively show that image processing methods considerably improve the ratios. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

26 pages, 10071 KiB  
Article
Aerodynamic Force and Comprehensive Mechanical Performance of a Large Wind Turbine during a Typhoon Based on WRF/CFD Nesting
by Shitang Ke, Wenlin Yu, Jiufa Cao and Tongguang Wang
Appl. Sci. 2018, 8(10), 1982; https://0-doi-org.brum.beds.ac.uk/10.3390/app8101982 - 19 Oct 2018
Cited by 13 | Viewed by 3590
Abstract
Compared with normal wind, typhoons may change the flow field surrounding wind turbines, thus influencing their wind-induced responses and stability. The existing typhoon theoretical model in the civil engineering field is too simplified. To address this problem, the WRF (Weather Research Forecasting) model [...] Read more.
Compared with normal wind, typhoons may change the flow field surrounding wind turbines, thus influencing their wind-induced responses and stability. The existing typhoon theoretical model in the civil engineering field is too simplified. To address this problem, the WRF (Weather Research Forecasting) model was introduced for high-resolution simulation of the Typhoon “Nuri” firstly. Secondly, the typhoon field was analyzed, and the wind speed profile of the boundary layer was fitted. Meanwhile, the normal wind speed profile with the same wind speed of the typhoon speed profile at the gradient height of class B landform in the code was set. These two wind speed profiles were integrated into the UDF (User Defined Function). On this basis, a five-MW wind turbine in Shenzhen was chosen as the research object. The action mechanism of speed was streamlined and turbulence energy surrounding the wind turbine was disclosed by microscale CFD (Computational Fluid Dynamics) simulation. The influencing laws of a typhoon and normal wind on wind pressure distribution were compared. Finally, key attention was paid to analyzing the structural response, buckling stability, and ultimate bearing capacity of the wind turbine system. The research results demonstrated that typhoons increased the aerodynamic force and structural responses, and decreased the overall buckling stability and ultimate bearing capacity of the wind turbine. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

18 pages, 5448 KiB  
Article
Impact of Economic Indicators on the Integrated Design of Wind Turbine Systems
by Jianghai Wu, Tongguang Wang, Long Wang and Ning Zhao
Appl. Sci. 2018, 8(9), 1668; https://0-doi-org.brum.beds.ac.uk/10.3390/app8091668 - 15 Sep 2018
Cited by 2 | Viewed by 3785
Abstract
This article presents a framework to integrate and optimize the design of large-scale wind turbines. Annual energy production, load analysis, the structural design of components and the wind farm operation model are coupled to perform a system-level nonlinear optimization. As well as the [...] Read more.
This article presents a framework to integrate and optimize the design of large-scale wind turbines. Annual energy production, load analysis, the structural design of components and the wind farm operation model are coupled to perform a system-level nonlinear optimization. As well as the commonly used design objective levelized cost of energy (LCoE), key metrics of engineering economics such as net present value (NPV), internal rate of return (IRR) and the discounted payback time (DPT) are calculated and used as design objectives, respectively. The results show that IRR and DPT have the same effect as LCoE since they all lead to minimization of the ratio of the capital expenditure to the energy production. Meanwhile, the optimization for NPV tends to maximize the margin between incomes and costs. These two types of economic metrics provide the minimal blade length and maximal blade length of an optimal blade for a target wind turbine at a given wind farm. The turbine properties with respect to the blade length and tower height are also examined. The blade obtained with economic optimization objectives has a much larger relative thickness and smaller chord distributions than that obtained for high aerodynamic performance design. Furthermore, the use of cost control objectives in optimization is crucial in improving the economic efficiency of wind turbines and sacrificing some aerodynamic performance can bring significant reductions in design loads and turbine costs. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

24 pages, 1713 KiB  
Article
Assessment of Turbulence Modelling in the Wake of an Actuator Disk with a Decaying Turbulence Inflow
by Hugo Olivares-Espinosa, Simon-Philippe Breton, Karl Nilsson, Christian Masson, Louis Dufresne and Stefan Ivanell
Appl. Sci. 2018, 8(9), 1530; https://0-doi-org.brum.beds.ac.uk/10.3390/app8091530 - 01 Sep 2018
Cited by 5 | Viewed by 3658
Abstract
The characteristics of the turbulence field in the wake produced by a wind turbine model are studied. To this aim, a methodology is developed and applied to replicate wake measurements obtained in a decaying homogeneous turbulence inflow produced by a wind tunnel. In [...] Read more.
The characteristics of the turbulence field in the wake produced by a wind turbine model are studied. To this aim, a methodology is developed and applied to replicate wake measurements obtained in a decaying homogeneous turbulence inflow produced by a wind tunnel. In this method, a synthetic turbulence field is generated to be employed as an inflow of Large-Eddy Simulations performed to model the flow development of the decaying turbulence as well as the wake flow behind an actuator disk. The implementation is carried out on the OpenFOAM platform, resembling a well-documented procedure used for wake flow simulations. The proposed methodology is validated by comparing with experimental results, for two levels of turbulence at inflow and disks with two different porosities. It is found that mean velocities and turbulent kinetic energy behind the disk are well estimated. The development of turbulence lengthscales behind the disk resembles what is observed in the free flow, predicting the ambient turbulence lengthscales to dominate across the wake, with little effect of shear from the wake envelope. However, observations of the power spectra confirm that shear yields a boost to the turbulence energy within the wake noticeable only in the low turbulence case. The results obtained show that the present implementation can successfully be used in the modelling and analysis of turbulence in wake flows. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

19 pages, 11007 KiB  
Article
Accurate RANS Simulation of Wind Turbine Stall by Turbulence Coefficient Calibration
by Wei Zhong, Hongwei Tang, Tongguang Wang and Chengyong Zhu
Appl. Sci. 2018, 8(9), 1444; https://0-doi-org.brum.beds.ac.uk/10.3390/app8091444 - 23 Aug 2018
Cited by 19 | Viewed by 3808
Abstract
Stall, a complex phenomenon related to flow separation, is difficult to be predicted accurately. The motivation of the present study is to propose an approach to improve the simulation accuracy of Reynolds Averaged Navier–Stokes equations (RANS) for wind turbines in stall. The approach [...] Read more.
Stall, a complex phenomenon related to flow separation, is difficult to be predicted accurately. The motivation of the present study is to propose an approach to improve the simulation accuracy of Reynolds Averaged Navier–Stokes equations (RANS) for wind turbines in stall. The approach is implemented in three steps in simulations of the S809 airfoil and the NREL (National Renewable Energy Laboratory) Phase VI rotor. The similarity between airfoil and rotor simulations is firstly investigated. It is found that the primary reason for the inaccuracy of rotor simulation is not the rotational effect or the 3-D effect, but the turbulence-related problem that already exists in airfoil simulation. Secondly, a coefficient of the SST turbulence model is calibrated in airfoil simulation, ensuring the onset and development of the light stall are predicted accurately. The lift of the airfoil in the light stall, which was overestimated about 30%, is reduced to a level consistent with experimental data. Thirdly, the calibrated coefficient is applied to rotor simulation. That makes the flow patterns on the blade properly simulated and the pressure distribution of the blade, as well as the torque of the rotor, are predicted more accurately. The relative error of the predicted maximum torque is reduced from 34.4% to 3.2%. Furthermore, the procedure of calibration is applied to the MEXICO (Model Experiments in Controlled Conditions) rotor, and the predicted pressure distributions over blade sections are better than the CFD (Computational Fluid Dynamics) results from the Mexnext project. In essence, the present study provides an approach for calibrating rotor simulation using airfoil experimental data, which enhances the potential of RANS in accurate simulation of the wind turbine aerodynamic performance. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

16 pages, 5258 KiB  
Article
Evaluation of the Power-Law Wind-Speed Extrapolation Method with Atmospheric Stability Classification Methods for Flows over Different Terrain Types
by Chang Xu, Chenyan Hao, Linmin Li, Xingxing Han, Feifei Xue, Mingwei Sun and Wenzhong Shen
Appl. Sci. 2018, 8(9), 1429; https://0-doi-org.brum.beds.ac.uk/10.3390/app8091429 - 22 Aug 2018
Cited by 16 | Viewed by 3675
Abstract
The atmospheric stability and ground topography play an important role in shaping wind-speed profiles. However, the commonly used power-law wind-speed extrapolation method is usually applied, ignoring atmospheric stability effects. In the present work, a new power-law wind-speed extrapolation method based on atmospheric stability [...] Read more.
The atmospheric stability and ground topography play an important role in shaping wind-speed profiles. However, the commonly used power-law wind-speed extrapolation method is usually applied, ignoring atmospheric stability effects. In the present work, a new power-law wind-speed extrapolation method based on atmospheric stability classification is proposed and evaluated for flows over different types of terrain. The method uses the wind shear exponent estimated in different stability conditions rather than its average value in all stability conditions. Four stability classification methods, namely the Richardson Gradient (RG) method, the Wind Direction Standard Deviation (WDSD) method, the Wind Speed Ratio (WSR) method and the Monin–Obukhov (MO) method are applied in the wind speed extrapolation method for three different types of terrain. Tapplicability is analyzed by comparing the errors between the measured data and the calculated results at the hub height. It is indicated that the WSR classification method is effective for all the terrains investigated while the WDSD method is more suitable in plain areas. Moreover, the RG and MO methods perform better in complex terrains than the other methods, if two-level temperature data are available. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

12 pages, 2012 KiB  
Article
Measurements of High-Frequency Atmospheric Turbulence and Its Impact on the Boundary Layer of Wind Turbine Blades
by Alois Peter Schaffarczyk and Andreas Jeromin
Appl. Sci. 2018, 8(9), 1417; https://0-doi-org.brum.beds.ac.uk/10.3390/app8091417 - 21 Aug 2018
Cited by 6 | Viewed by 3304
Abstract
To gain insight into the differences between onshore and offshore atmospheric turbulence, pressure fluctuations were measured for offshore wind under different environmental conditions. A durable piezo-electric sensor was used to sample turbulent pressure data at 50 kHz. Offshore measurements were performed at a [...] Read more.
To gain insight into the differences between onshore and offshore atmospheric turbulence, pressure fluctuations were measured for offshore wind under different environmental conditions. A durable piezo-electric sensor was used to sample turbulent pressure data at 50 kHz. Offshore measurements were performed at a height of 100 m on Germany’s FINO3 offshore platform in the German Bight together with additional meteorological data provided by Deutscher Wetterdienst (DWD). The statistical evaluation revealed that the stability state in the atmospheric boundary does not seem to depend on simple properties like the Reynolds number, wind speed, wind direction, or turbulence level. Therefore, we used higher statistical properties (described by so-called shape factors) to relate them to the stability state. Data was classified to be either within an unstable, neutral, or stable stratification. We found that, in case of stable stratification, the shape factor was mostly close to zero, indicating that a thermally stable environment produces closer-to Gaussian distributions. Non-Gaussian distributions were found in unstable and neutral boundary layer states, and an occurrence probability was estimated. Possible impacts on the laminar-turbulent transition on the blade are discussed with the application of so-called laminar airfoils on wind turbine blades. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

20 pages, 4936 KiB  
Article
Comparative Study of Dynamic Stall under Pitch Oscillation and Oscillating Freestream on Wind Turbine Airfoil and Blade
by Chengyong Zhu and Tongguang Wang
Appl. Sci. 2018, 8(8), 1242; https://0-doi-org.brum.beds.ac.uk/10.3390/app8081242 - 27 Jul 2018
Cited by 19 | Viewed by 4664
Abstract
This study aims to assess the dynamic stall of the wind turbine blade undergoing pitch oscillation (PO) and oscillating freestream (OF), respectively. Firstly, a thin-airfoil theoretical analysis was performed to differentiate between these two dynamic effects. During upstroke, PO results in a positive [...] Read more.
This study aims to assess the dynamic stall of the wind turbine blade undergoing pitch oscillation (PO) and oscillating freestream (OF), respectively. Firstly, a thin-airfoil theoretical analysis was performed to differentiate between these two dynamic effects. During upstroke, PO results in a positive effective airfoil camber, while OF has an additional negative effective airfoil camber, and yet in contrast during downstroke, PO decreases the effective camber, while OF increases the effective camber. Secondly, the equivalence relation between PO and OF is investigated by numerically solving the unsteady Reynolds-averaged Navier-Stokes equations. The difference between PO and OF mainly exists in the linear part of the aerodynamic loads. Because the difference is great at high reduced frequencies or angle of attack (AOA) amplitudes, PO and OF should be treated separately for dynamic stall from different aerodynamic sources. Thirdly, the Beddoes-Leishman dynamic model coupled with Bak’s rotational stall delay model was used to predict the yawed responses of the blade section. The obtained results show different aerodynamic responses between PO and OF, although consideration of rotational augmentation can greatly improve the accuracy of the lift and drag coefficients. To improve the understanding and coupling modeling of rotational augmentation and dynamic stall, an extended analysis of the coupled effect was performed as well. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

18 pages, 3688 KiB  
Article
Wind Turbine Optimization for Minimum Cost of Energy in Low Wind Speed Areas Considering Blade Length and Hub Height
by Han Yang, Jin Chen and Xiaoping Pang
Appl. Sci. 2018, 8(7), 1202; https://0-doi-org.brum.beds.ac.uk/10.3390/app8071202 - 23 Jul 2018
Cited by 28 | Viewed by 5428
Abstract
In recent years, sites with low annual average wind speeds have begun to be considered for the development of new wind farms. The majority of design methods for a wind turbine operating at low wind speed is to increase the blade length or [...] Read more.
In recent years, sites with low annual average wind speeds have begun to be considered for the development of new wind farms. The majority of design methods for a wind turbine operating at low wind speed is to increase the blade length or hub height compared to a wind turbine operating in high wind speed sites. The cost of the rotor and the tower is a considerable portion of the overall wind turbine cost. This study investigates a method to trade-off the blade length and hub height during the wind turbine optimization at low wind speeds. A cost and scaling model is implemented to evaluate the cost of energy. The procedure optimizes the blades’ aero-structural performance considering blade length and the hub height simultaneously. The blade element momentum (BEM) code is used to evaluate blade aerodynamic performance and classical laminate theory (CLT) is applied to estimate the stiffness and mass per unit length of each blade section. The particle swarm optimization (PSO) algorithm is applied to determine the optimal wind turbine with the minimum cost of energy (COE). The results show that increasing rotor diameter is less efficient than increasing the hub height for a low wind speed turbine and the COE reduces 16.14% and 17.54% under two design schemes through the optimization. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

15 pages, 3330 KiB  
Article
Optimize Rotating Wind Energy Rotor Blades Using the Adjoint Approach
by Lena Vorspel, Bernhard Stoevesandt and Joachim Peinke
Appl. Sci. 2018, 8(7), 1112; https://0-doi-org.brum.beds.ac.uk/10.3390/app8071112 - 10 Jul 2018
Cited by 9 | Viewed by 3191
Abstract
Wind energy rotor blades are highly complex structures, both combining a large aerodynamic efficiency and a robust structure for lifetimes up to 25 years and more. Current research deals with smart rotor blades, improved for turbulent wind fields, less maintenance and low wind [...] Read more.
Wind energy rotor blades are highly complex structures, both combining a large aerodynamic efficiency and a robust structure for lifetimes up to 25 years and more. Current research deals with smart rotor blades, improved for turbulent wind fields, less maintenance and low wind sites. In this work, an optimization tool for rotor blades using bend-twist-coupling is developed and tested. The adjoint approach allows computation of gradients based on the flow field at comparably low cost. A suitable projection method from the large design space of one gradient per numerical grid cell to a suitable design space for rotor blades is derived. The adjoint solver in OpenFOAM is extended for external flow. As novelty, we included rotation via the multiple reference frame method, both for the flow and the adjoint field. This optimization tool is tested for the NREL Phase VI turbine, optimizing the thrust by twisting of various outer parts between 20–50% of the blade length. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

17 pages, 12938 KiB  
Article
Aerodynamic Performance of Wind Turbine Airfoil DU 91-W2-250 under Dynamic Stall
by Shuang Li, Lei Zhang, Ke Yang, Jin Xu and Xue Li
Appl. Sci. 2018, 8(7), 1111; https://0-doi-org.brum.beds.ac.uk/10.3390/app8071111 - 10 Jul 2018
Cited by 15 | Viewed by 5276
Abstract
Airfoils are subjected to the ‘dynamic stall’ phenomenon in significant pitch oscillations during the actual operation process of wind turbines. Dynamic stall will result in aerodynamic fatigue loads and further cause a discrepancy in the aerodynamic performance between design and operation. In this [...] Read more.
Airfoils are subjected to the ‘dynamic stall’ phenomenon in significant pitch oscillations during the actual operation process of wind turbines. Dynamic stall will result in aerodynamic fatigue loads and further cause a discrepancy in the aerodynamic performance between design and operation. In this paper, a typical wind turbine airfoil, DU 91-W2-250, is examined numerically using the transition shear stress transport (SST) model under a Reynolds number of 3×105. The influence of a reduced frequency on the unsteady dynamic performance of the airfoil model is examined by analyzing aerodynamic coefficients, pressure contours and separation point positions. It is concluded that an increasingly-reduced frequency leads to lower aerodynamic efficiency during the upstroke process of pitching motions. The results show the movement of the separation point and the variation of flow structures in a hysteresis loop. Additionally, the spectrum of pressure signals on the suction surface is analyzed, exploring the level of dependence of pressure fluctuation on the shedding vortex and oscillation process. It provides a theoretical basis for the understanding of the dynamic stall of the wind turbine airfoil. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

21 pages, 8384 KiB  
Article
Development of a CFD-Based Wind Turbine Rotor Optimization Tool in Considering Wake Effects
by Jiufa Cao, Weijun Zhu, Wenzhong Shen, Jens Nørkær Sørensen and Tongguang Wang
Appl. Sci. 2018, 8(7), 1056; https://0-doi-org.brum.beds.ac.uk/10.3390/app8071056 - 28 Jun 2018
Cited by 8 | Viewed by 4164
Abstract
In the present study, a computational fluid dynamic (CFD)-based blade optimization algorithm is introduced for designing single or multiple wind turbine rotors. It is shown that the CFD methods provide more detailed aerodynamics features during the design process. Because high computational cost limits [...] Read more.
In the present study, a computational fluid dynamic (CFD)-based blade optimization algorithm is introduced for designing single or multiple wind turbine rotors. It is shown that the CFD methods provide more detailed aerodynamics features during the design process. Because high computational cost limits the conventional CFD applications in particular for rotor optimization purposes, in the current paper, a CFD-based 2D Actuator Disc (AD) model is used to represent turbulent flows over wind turbine rotors. With the ideal case of axisymmetric flows, the simulation time is significantly reduced with the 2D method. The design variables are the shape parameters comprising the chord, twist, and relative thickness of the wind turbine rotor blades as well as the rotational speed. Due to the wake effects, the optimized blade shapes are different for the upstream and downstream turbines. The comparative aerodynamic performance is analyzed between the original and optimized reference wind turbine rotor. The results show that the present numerical optimization algorithm for multiple turbines is efficient and more advanced than conventional methods. The current method achieves the same accuracy as 3D CFD simulations, and the computational efficiency is not significantly higher than the Blade Element Momentum (BEM) theory. The paper shows that CFD for rotor design is possible using a high-performance single personal computer with multiple cores. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

23 pages, 8056 KiB  
Article
Variable Pitch Approach for Performance Improving of Straight-Bladed VAWT at Rated Tip Speed Ratio
by Zhenzhou Zhao, Ruixin Wang, Wenzhong Shen, Tongguang Wang, Bofeng Xu, Yuan Zheng and Siyue Qian
Appl. Sci. 2018, 8(6), 957; https://0-doi-org.brum.beds.ac.uk/10.3390/app8060957 - 11 Jun 2018
Cited by 28 | Viewed by 5593
Abstract
This paper presents a new variable pitch (VP) approach to increase the peak power coefficient of the straight-bladed vertical-axis wind turbine (VAWT), by widening the azimuthal angle band of the blade with the highest aerodynamic torque, instead of increasing the highest torque. The [...] Read more.
This paper presents a new variable pitch (VP) approach to increase the peak power coefficient of the straight-bladed vertical-axis wind turbine (VAWT), by widening the azimuthal angle band of the blade with the highest aerodynamic torque, instead of increasing the highest torque. The new VP-approach provides a curve of pitch angle designed for the blade operating at the rated tip speed ratio (TSR) corresponding to the peak power coefficient of the fixed pitch (FP)-VAWT. The effects of the new approach are exploited by using the double multiple stream tubes (DMST) model and Prandtl’s mathematics to evaluate the blade tip loss. The research describes the effects from six aspects, including the lift, drag, angle of attack (AoA), resultant velocity, torque, and power output, through a comparison between VP-VAWTs and FP-VAWTs working at four TSRs: 4, 4.5, 5, and 5.5. Compared with the FP-blade, the VP-blade has a wider azimuthal zone with the maximum AoA, lift, drag, and torque in the upwind half-cycle, and yields the two new larger maximum values in the downwind half-cycle. The power distribution in the swept area of the turbine changes from an arched shape of the FP-VAWT into the rectangular shape of the VP-VAWT. The new VP-approach markedly widens the highest-performance zone of the blade in a revolution, and ultimately achieves an 18.9% growth of the peak power coefficient of the VAWT at the optimum TSR. Besides achieving this growth, the new pitching method will enhance the performance at TSRs that are higher than current optimal values, and an increase of torque is also generated. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Graphical abstract

18 pages, 4980 KiB  
Article
A Simplified Free Vortex Wake Model of Wind Turbines for Axial Steady Conditions
by Bofeng Xu, Tongguang Wang, Yue Yuan, Zhenzhou Zhao and Haoming Liu
Appl. Sci. 2018, 8(6), 866; https://0-doi-org.brum.beds.ac.uk/10.3390/app8060866 - 25 May 2018
Cited by 14 | Viewed by 4328
Abstract
A simplified free vortex wake (FVW) model called the vortex sheet and ring wake (VSRW) model was developed to rapidly calculate the aerodynamic performance of wind turbines under axial steady conditions. The wake in the simplified FVW model is comprised of the vortex [...] Read more.
A simplified free vortex wake (FVW) model called the vortex sheet and ring wake (VSRW) model was developed to rapidly calculate the aerodynamic performance of wind turbines under axial steady conditions. The wake in the simplified FVW model is comprised of the vortex sheets in the near wake and the vortex rings, which are used to replace the helical tip vortex filament in the far wake. The position of the vortex ring is obtained by the motion equation of its control point. Analytical formulas of the velocity induced by the vortex ring were introduced to reduce the computational time of the induced velocity calculation. In order to take into account both accuracy and calculation time of the VSRW model, the length of the near wake was cut off at a 120° wake age angle. The simplified FVW model was used to calculate the aerodynamic load of the blade and the wake flow characteristic. The results were compared with measurement results and the results from the full vortex sheet wake model and the tip vortex wake model. The computational speed of the simplified FVW model is at least an order of magnitude faster than other two conventional models. The error of the low-speed shaft torque obtained from the simplified FVW model is no more than 10% relative to the experiment at most of wind speeds. The normal and tangential force coefficients obtained from the three models agree well with each other and with the measurement results at the low wind speed. The comparison indicates that the simplified FVW model predicts the aerodynamic load accurately and greatly reduces the computational time. The axial induction factor field in the near wake agrees well with the other two FVW models and the radial expansion deformation of the wake can be captured. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

21 pages, 10471 KiB  
Article
CFD Simulations of Flows in a Wind Farm in Complex Terrain and Comparisons to Measurements
by Matias Sessarego, Wen Zhong Shen, Maarten Paul Van der Laan, Kurt Schaldemose Hansen and Wei Jun Zhu
Appl. Sci. 2018, 8(5), 788; https://0-doi-org.brum.beds.ac.uk/10.3390/app8050788 - 15 May 2018
Cited by 32 | Viewed by 5238
Abstract
This article describes Computational Fluid Dynamics (CFD) simulations of flows in a wind farm in complex terrain in Shaanxi, China and the comparisons of the computational results with utility scale field measurements. The CFD simulations performed in the study are using either a [...] Read more.
This article describes Computational Fluid Dynamics (CFD) simulations of flows in a wind farm in complex terrain in Shaanxi, China and the comparisons of the computational results with utility scale field measurements. The CFD simulations performed in the study are using either a Reynolds-Averaged Navier–Stokes (RANS) or Large-Eddy Simulation (LES) solver. The RANS method together with an Actuator Disc (AD) approach is employed to predict the performance of the 25 wind turbines in the farm, while the LES and Actuator Line (AL) technique is used to obtain a detailed description of the flow field around a specific wind turbine #14 near two met masts. The AD-RANS simulation results are compared with the mean values of power obtained from field measurements. Furthermore, the AL-LES results are compared with the mean values of power, rotor speed, and wind speed measured from the wind turbine and its nearby two masts. Results from the simulations indicate that both AD-RANS and AL-LES methods can reasonably predict the performance of the wind farm and wind turbine #14, respectively, in complex terrain in Shaanxi. The mean percent difference obtained for power in the AD-RANS simulations was approximately 20%. Percent differences obtained for power and rotor RPM in the AL-LES varied between 0.08% and 11.6%. The mean percent differences in the AL-LES for power and rotor RPM are approximately 7% and 1%, respectively. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Figure 1

17 pages, 7126 KiB  
Article
Aerodynamics and Motion Performance of the H-Type Floating Vertical Axis Wind Turbine
by Ying Guo, Liqin Liu, Xifeng Gao and Wanhai Xu
Appl. Sci. 2018, 8(2), 262; https://0-doi-org.brum.beds.ac.uk/10.3390/app8020262 - 09 Feb 2018
Cited by 9 | Viewed by 6119
Abstract
Aerodynamics and motion performance of the floating vertical wind turbine (VAWT) were studied in this paper, where the wind turbine was H-type and the floating foundation was truss spar type. Based on the double-multiple-stream-tube theory, the formulae were deduced to calculate the aerodynamic [...] Read more.
Aerodynamics and motion performance of the floating vertical wind turbine (VAWT) were studied in this paper, where the wind turbine was H-type and the floating foundation was truss spar type. Based on the double-multiple-stream-tube theory, the formulae were deduced to calculate the aerodynamic loads acting on the wind turbine considering the motions of the floating foundation. The surge-heave-pitch nonlinear coupling equations of the H-type floating VAWT were established. Aerodynamics and motion performance of a 5 MW H-type floating VAWT was studied, and the effect of the floating foundation motions on the aerodynamic loads was analyzed. It is shown that the motions of the floating foundation on the aerodynamics cannot be ignored. The motion of the H-type floating VAWT was also compared with that of the Φ-type floating VAWT: they have the same floating foundation, rated output power, mooring system and total displacement. The results show that the H-type floating VAWT has better motion performance, and the mean values of surge, heave and pitch of the H-type floating VAWT are much smaller comparing with the Φ-type floating VAWT. Full article
(This article belongs to the Special Issue Wind Turbine Aerodynamics)
Show Figures

Graphical abstract

Back to TopTop