materials-logo

Journal Browser

Journal Browser

Corrosion, Properties and Characterization in Concrete

A special issue of Materials (ISSN 1996-1944). This special issue belongs to the section "Construction and Building Materials".

Deadline for manuscript submissions: closed (20 September 2023) | Viewed by 31153

Special Issue Editors

Department of Infrastructure Engineering, The University of Melbourne, Parkville, VIC 3010, Australia
Interests: concrete corrosion; reactive transport of sulfate and chloride ions in concrete; performance assessment of glass and aluminum cladding against hail storms; engineering reliability; machine learning
School of Materials Science and Engineering, Tongji University, Shanghai 201804, China
Interests: concrete durability; functional materials; multi-scale determination

Special Issue Information

Dear Colleagues,

Due to the low cost, ready availability, and comprehensive performance of raw materials, concrete has been widely used in the construction of engineering structures for many decades. However, the durability of reinforced concrete (RC) structures could be significantly compromised under extreme environmental conditions, such as sulfate and chlorine ion attack in a marine environment. As the deterioration of concrete could lead to the significant reduction in the service life of RC structures, and the ultimately the potential loss of billions of dollars, the fundamental understanding of corrosion, properties and characterization in concrete becomes increasingly important. With the development of microscopic new techniques in material science in last decade, significant advances have been made in capturing the change in the microstructure of concrete at different degrading stages under various environmental conditions. In addition, the development of modern concrete using supplementary cementitious materials (e.g., fly ash and slag) and the application of advanced 3D printing and nanotechnology represent the direction of future concrete development. This Special Issue contributes to a useful reference for further research and development of new advanced concrete technology to prolong the service-life of concrete structures.

Prof. Dr. Lihai Zhang
Dr. Kai Wu
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Materials is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • concrete
  • corrosion
  • microstructure
  • fly ash and slag
  • nanotechnology
  • 3D printing
  • microscopy

Published Papers (19 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

14 pages, 4291 KiB  
Article
The Influence Mechanism of Interfacial Characteristics between CSH and Montmorillonite on the Strength Properties of Cement-Stabilized Montmorillonite Soil
by Jinyu Ge, Fei Xu, Hua Wei, Qiang Wang, Hu Peng, Juan Zhou and Huaisen Li
Materials 2023, 16(22), 7141; https://0-doi-org.brum.beds.ac.uk/10.3390/ma16227141 - 13 Nov 2023
Viewed by 659
Abstract
To elucidate the impact mechanism of the interfacial characteristics of Calcium Silicate Hydrate gel (CSH)–Montmorillonite (MMT) at the nanoscale on the strength of cement-stabilized montmorillonite soil, this paper begins by examining the interfacial energy. Through Molecular Dynamics (MD) simulation methods, the energy at [...] Read more.
To elucidate the impact mechanism of the interfacial characteristics of Calcium Silicate Hydrate gel (CSH)–Montmorillonite (MMT) at the nanoscale on the strength of cement-stabilized montmorillonite soil, this paper begins by examining the interfacial energy. Through Molecular Dynamics (MD) simulation methods, the energy at the MMT and CSH binding interface is quantitatively calculated, and the correlation between the interfacial energy and macroscopic strength is determined in conjunction with grey relational analysis. Finally, based on the characterization results from X-ray diffraction (XRD), the accuracy and sources of deviation in the MD simulation results are discussed. The study shows the CSH-MMT interfacial energy is composed of van der Waals forces, hydrogen bond energy, and electrostatic interactions, which are influenced by the migration of cations; there is a good consistency between the CSH-MMT interfacial energy and the unconfined compressive strength (UCS) of cement-stabilized soil (cemented soil), with the interfacial energy decreasing as the number of water molecules increases and first decreasing then increasing as the number of MMT layers grows; by adjusting the mix proportions, the magnitude of the CSH-MMT interfacial energy can be altered, thereby optimizing the strength of the cemented soil. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

17 pages, 4072 KiB  
Article
Corrosion Activity of Stainless Steel SS430 and Carbon Steel B450C in a Sodium Silicate Modified Limestone-Portland Cement Extract
by David Bonfil, Lucien Veleva, Sebastian Feliu, Jr. and José Iván Escalante-García
Materials 2023, 16(14), 5066; https://0-doi-org.brum.beds.ac.uk/10.3390/ma16145066 - 18 Jul 2023
Viewed by 838
Abstract
Stainless steel SS430 and carbon steel B450C were exposed for 30 days to the aqueous extract of sodium silicate-modified limestone-Portland cement as an alternative for the partial replacement of the Portland cement clinker. The initial pH of 12.60 was lowered and maintained at [...] Read more.
Stainless steel SS430 and carbon steel B450C were exposed for 30 days to the aqueous extract of sodium silicate-modified limestone-Portland cement as an alternative for the partial replacement of the Portland cement clinker. The initial pH of 12.60 was lowered and maintained at an average of 9.60, associated with air CO2 dissolution and acidification. As a result, the carbon steel lost its passive state, and the corrosion potential (OCP) reached a negative value of up to 296 mV, forming the corrosion layer of FeO, and FeOOH. In the meaning time, on the stainless steel SS430 surface, a passive layer of Cr2O3 grew in the presence of FeO, Fe2O3 and Cr(OH)3 corrosion products; thus, the OCP shifted to more positive values of +150 mV. It is suggested that a self-repassivation process took place on the SS430 surface due to the accumulation of alkaline sulfates on the interface. Because of the chloride attack, SS430 presented isolated pits, while on B450C, their area was extended. The quantitative analysis of EIS Nyquist and Bode diagrams revealed that the Rp of the corrosion process for SS430 was 2500 kΩcm2, ≈32 times lower in magnitude than on B450C, for which the passive layer tended to disappear, while that on SS430 was ≈0.82 nm. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

17 pages, 7532 KiB  
Article
Experimental Investigation on Interface Performance of UHPC-Strengthened NC Structure through Push-Out Tests
by Yun-Chuan Zhao, Hong-Gang Lei, Lang-Kuo Guo and Guo-Yun Lu
Materials 2023, 16(5), 1766; https://0-doi-org.brum.beds.ac.uk/10.3390/ma16051766 - 21 Feb 2023
Cited by 2 | Viewed by 1100
Abstract
Strengthening concrete structures with ultra-high performance concrete (UHPC) can both improve the bearing capacity of the original normal concrete (NC) structure and prolong the service life of the structure due to the high strength and durability of UHPC. The key to the synergistic [...] Read more.
Strengthening concrete structures with ultra-high performance concrete (UHPC) can both improve the bearing capacity of the original normal concrete (NC) structure and prolong the service life of the structure due to the high strength and durability of UHPC. The key to the synergistic work of the UHPC-strengthened layer and the original NC structures lies in the reliable bonding of their interfaces. In this research study, the shear performance of the UHPC–NC interface was investigated by the direct shear (push-out test) test method. The effects of different interface preparation methods (smoothing, chiseling, and planting straight and hooked rebars) and different aspect ratios of planted rebars on the failure mode and shear performance of the pushed-out specimens were studied. Seven groups of push-out specimens were tested. The results show that the interface preparation method can significantly affect the failure mode of the UHPC–NC interface, which is specifically divided into interface failure, planted rebar pull-out, and NC shear failure. The critical aspect ratio for the pull-out or anchorage of planted rebars in UHPC is around 2. The interface shear strength of straight-planted rebar interface preparation is significantly improved compared with that of the chiseled and smoothened interfaces, and as the embedding length of the planted rebar becomes longer, it first increases greatly and then tends to be stable when the rebar planted in UHPC is fully anchored. The shear stiffness of UHPC–NC increases with the increase of the aspect ratio of planted rebars. A design recommendation based on the experimental results is proposed. This research study supplements the theoretical basis of the interface design of UHPC-strengthened NC structures. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

15 pages, 3174 KiB  
Article
Investigation on Roles of Packing Density and Water Film Thickness in Synergistic Effects of Slag and Silica Fume
by Yunchuan Zhao, Xuming Dong, Zicun Zhou, Jiangfeng Long, Guoyun Lu and Honggang Lei
Materials 2022, 15(24), 8978; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15248978 - 15 Dec 2022
Cited by 3 | Viewed by 1109
Abstract
The ternary blended cement with finer slag and silica fume (SF) could improve the packing density (PD) through the filling effect. The excess water (water more than needed for filling into voids between the cement particles) can be released to improve the fresh [...] Read more.
The ternary blended cement with finer slag and silica fume (SF) could improve the packing density (PD) through the filling effect. The excess water (water more than needed for filling into voids between the cement particles) can be released to improve the fresh properties and densify the microstructure which is beneficial for improving the hardened properties. To verify the hypothesis and reveal how and why (cement + slag + SF) the ternary blends could bring such advantages, the binder pastes incorporating slag and SF with various water-to-binder ratios were produced to determine the PD experimentally. To evaluate the optimum water demand (OWD) for maximum wet density, the influence of the dispersion state of the binder on PD was investigated using the wet packing density approach. The effect of PD of various binary and ternary binder systems on water film thickness (WFT), fluidity, setting time, and compressive strength development of cement paste was also investigated. The results show that the ternary blends could improve the PD and decrease the water film thickness (WFT). The enhanced PD and altered WFT are able to increase fluidity and compressive strength. The ternary blends could improve the compressive strengths by increasing PD and exerting nucleation and pozzolanic effects. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

16 pages, 8708 KiB  
Article
Mechanical Properties Evaluation of Polymer-Binding C-S-H Structure from Nanoscale to Macroscale: Hydroxyl-Terminated Polydimethylsiloxane (PDMS) Modified C-S-H
by Zheyu Zhu, Yue Zhou, Zhishan Huang, Zhongping Wang and Yuting Chen
Materials 2022, 15(23), 8361; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15238361 - 24 Nov 2022
Cited by 5 | Viewed by 1115
Abstract
Exploring and modifying the C-S-H structure at a micro–nano level is an effective solution to improve the performance of Portland cement. Compared with organics inserting C-S-H, the research on the performance of a polymer-binding C-S-H structure from nanoscale to macroscale is limited. In [...] Read more.
Exploring and modifying the C-S-H structure at a micro–nano level is an effective solution to improve the performance of Portland cement. Compared with organics inserting C-S-H, the research on the performance of a polymer-binding C-S-H structure from nanoscale to macroscale is limited. In this work, the mechanical properties of a modified C-S-H, using hydroxyl-terminated polydimethylsiloxane (PDMS) as the binders, are evaluated. The PDMS-modified C-S-H structures are introduced into macro-defect-free cement to obtain stress–strain curves changes at a macro scale. The AFM–FM was adopted to measure the morphology and elastic modulus of C-S-H at a nano scale. The molecular dynamics (MD) simulation was performed to assess the toughness, tensile properties, and failure mechanism. The results show that the PDMS-modified C-S-H powders change the break process and enhance ductility of MDF cement. The elastic modulus of PDMS-modified C-S-H is lower than pure C-S-H. When PDMS molecules are located between the stacking crystal units, it can enhance the toughness of C-S-H aggregates. The PDMS-modified C-S-H stacking structure has better plasticity, and its tensile strains are higher than the pure C-S-H. PDMS molecules hinder the initial crack expansion, leading to the branching of the initial crack. In addition, the measurement of AFM–FM can identify and obtain the mechanical properties of basic units of C-S-H. This paper enhances the understanding of cement strength sources and modification methods. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

16 pages, 3691 KiB  
Article
Experimental Study on the Flexural Properties of Concrete Beams Reinforced with Hybrid Steel/Fiber-Belt-Bars
by Wenhu Gu, Hengrui Liu and Yun Dong
Materials 2022, 15(10), 3505; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15103505 - 13 May 2022
Cited by 2 | Viewed by 1164
Abstract
Reinforcement corrosion poses a great threat to the safety of reinforced concrete structures, and the fiber-reinforced polymer is the ideal material to partially replace steel bars due to the high strength, light weight and good durability. However, the selection of appropriate fiber materials [...] Read more.
Reinforcement corrosion poses a great threat to the safety of reinforced concrete structures, and the fiber-reinforced polymer is the ideal material to partially replace steel bars due to the high strength, light weight and good durability. However, the selection of appropriate fiber materials and a reasonable ratio of fiber bar to steel bar is not clear. Here, we measured the mechanical properties of fiber bars containing aramid fiber and carbon fiber. The deflection deformation, crack distribution and maximum crack width of the concrete upon various loads were experimentally and theoretically investigated. The predictions of the maximum crack width and deflection of reinforced concrete beams under various loads were proposed in ACI standard, which may provide guidance for further applications of fiber-belt-bar-containing concrete beams. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

26 pages, 5786 KiB  
Article
Degradation Mechanism and Numerical Simulation of Pervious Concrete under Salt Freezing-Thawing Cycle
by Junzheng Xiang, Hengrui Liu, Hao Lu and Faliang Gui
Materials 2022, 15(9), 3054; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15093054 - 22 Apr 2022
Cited by 7 | Viewed by 1580
Abstract
In order to explore the occurrence area of pervious concrete freeze-thaw deterioration, the mass loss, strength deterioration, ultrasonic longitudinal wave velocity and dynamic elastic modulus attenuation of pervious concrete under freeze-thaw cycles were measured, and a prediction model of freeze-thaw damage was established. [...] Read more.
In order to explore the occurrence area of pervious concrete freeze-thaw deterioration, the mass loss, strength deterioration, ultrasonic longitudinal wave velocity and dynamic elastic modulus attenuation of pervious concrete under freeze-thaw cycles were measured, and a prediction model of freeze-thaw damage was established. The mechanical properties of hardened cement pastes with the same W/C ratio under freeze-thaw cycles were also measured. Mercury intrusion porosimetry (MIP) was used to measure the pore structure characteristic parameters and pore size distribution changes of cement paste under freeze-thaw cycle, and the microstructure evolution of interfacial transition zone (ITZ) of paste and aggregate was observed by SEM scanning electron microscopy. Finally, a pervious concrete model was established by DEM to analyze the relationship between the number of freeze-thaw cycles and the mesoscopic parameters. The results indicated that the quality, strength and dynamic elastic modulus of pervious concrete deteriorate to different degrees under the conditions of water freezing and salt freezing. The damage sensitivity and strength loss of freeze-thaw damage is greater than the dynamic elastic modulus loss, which is greater than mass loss. In the pervious concrete paste which underwent 100 freeze-thaw cycles, the pore structure and macro strength had no obvious change, and hardened paste and the aggregate-interface-generated defects increased with the increase in freezing and thawing times, indicating that the deterioration of pervious concrete performance under freeze-thaw cycles was closely related to the deterioration of the interface strength of the aggregate and hardened paste. The pervious concrete model established by DEM can accurately simulate the change of the compressive modulus and the strength of pervious concrete during freeze-thaw cycles. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

12 pages, 14683 KiB  
Article
Quantitative Analysis of the Calcium Hydroxide Content of EVA-Modified Cement Paste Based on TG-DSC in a Dual Atmosphere
by Zhenlei Zhang, Jiang Du and Meilun Shi
Materials 2022, 15(7), 2660; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15072660 - 04 Apr 2022
Cited by 6 | Viewed by 2329
Abstract
The calcium hydroxide (Ca(OH)2) content is one of the main indices of cement hydration degree. In order to accurately determine the calcium hydroxide content of ethylene and vinyl acetate (EVA) copolymer-modified cement paste, a dual atmosphere thermogravimetric method (first in an [...] Read more.
The calcium hydroxide (Ca(OH)2) content is one of the main indices of cement hydration degree. In order to accurately determine the calcium hydroxide content of ethylene and vinyl acetate (EVA) copolymer-modified cement paste, a dual atmosphere thermogravimetric method (first in an oxidizing atmosphere and then in an inert atmosphere) was used to track the mass loss and change in enthalpy by TG-DSC (simultaneous thermogravimetry and differential scanning calorimetry). The results showed that using the dual atmosphere thermogravimetric method, the source of mass loss can be distinguished. The exothermic peaks in an oxidizing atmosphere show the oxidation reactions of EVA, while the endothermic peak in an inert atmosphere is due to the pyrolysis reaction of EVA and the decomposition of the calcium hydroxide. The influence of EVA on cement hydration was investigated. The results showed that the polymer powder can be dispersed in water, forming a kind of composite membrane. The test method of dual atmosphere thermogravimetry to measure the calcium hydroxide content of polymer-modified cement pastes is more accurate and convenient than those previously applied. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

16 pages, 7390 KiB  
Article
Effect of Vehicle–Bridge Coupled Vibration on the Performance of Magnesium Phosphate Cement Repair Materials
by Sijia Liu, Long Yu, Hao Han, Feng Pan, Kai Wu and Zhenghong Yang
Materials 2021, 14(24), 7743; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14247743 - 15 Dec 2021
Cited by 3 | Viewed by 1737
Abstract
This study evaluates the effect of vehicle–bridge coupled vibration on the mechanical properties of fiber-reinforced magnesium phosphate cement (FR-MPC) composites and the bonding properties of repaired systems. By means of compressive and flexural bond strengths, fiber pullout, mercury intrusion porosimeter (MIP) and backscattered [...] Read more.
This study evaluates the effect of vehicle–bridge coupled vibration on the mechanical properties of fiber-reinforced magnesium phosphate cement (FR-MPC) composites and the bonding properties of repaired systems. By means of compressive and flexural bond strengths, fiber pullout, mercury intrusion porosimeter (MIP) and backscattered electron imaging (BSE) analysis, an enhanced insight was gained into the evolution of FR-MPC performance before and after vibration. Experimental results showed that the compressive strength and flexural strength of FR-MPC was increased when it was subjected to vibration. However, the effects of vibration on the flexural strength of plain magnesium phosphate cement (MPC) mortars was insignificant. The increased flexural strength of FR-MPC after vibration could be due to the high average bond strength and pull-out energy between the micro-steel fiber and the MPC matrix. Moreover, BSE analysis revealed that the interface structure between FR-MPC and an ordinary Portland cement (OPC) substrate was more compacted after vibration, which could possibly be responsible for the better bonding properties of FR-MPC. These findings are beneficial for construction project applications of FR-MPC in bridge repairing and widening. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

12 pages, 3637 KiB  
Article
Influence of Calcined Flue Gas Desulfurization Gypsum and Calcium Aluminate on the Strength and AFt Evolution of Fly Ash Blended Concrete under Steam Curing
by Yueran Zhang, Heng Zhang and Xiong Zhang
Materials 2021, 14(23), 7171; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14237171 - 25 Nov 2021
Cited by 6 | Viewed by 1333
Abstract
In order to improve the early strength of fly ash blended cement concrete under steam curing conditions, fly ash was partly substituted by calcined flue gas desulfurization (FGD) gypsum and active calcium aluminate. The effect of the composition and curing condition on the [...] Read more.
In order to improve the early strength of fly ash blended cement concrete under steam curing conditions, fly ash was partly substituted by calcined flue gas desulfurization (FGD) gypsum and active calcium aluminate. The effect of the composition and curing condition on the workability, mechanical property, and volume stability was systematically evaluated. The variety of hydration products and the evolution was determined by XRD to explore the formation kinetic of ettringite. Results show that the addition of calcined FGD gypsum and active calcium aluminate is able to improve the early compressive strength but using more FGD gypsum and a high sulfur aluminum ratio leads to a reduction in compressive strength from 28 to 90 days due to the increment of ettringite and crystallization of dihydrate gypsum. Both the free expansion ratio and limited expansion exhibited a continuous increasement with time, especially in the first 14 days of testing. Cracks were not observed on the surface of samples immersed in water for a year. The improvement of strength and shrinkage resistance is mainly due to the formation of ettringite generated before 14 days and the precipitation was highly limited from 14 to 28 days. Moreover, the characteristic peak of gypsum appeared after 28 days, indicating the conversion of partial of calcined FGD gypsum. The work presented here provides a new solution for improving the early strength of fly ash concrete without reducing the later strength and consuming extra energy. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

15 pages, 16284 KiB  
Article
Performance and Nanostructure Simulation of Phosphogypsum Modified by Sodium Carbonate and Alum
by Dongqing Zhong, Jingchen Wang, Guihua Hou, Luming Wang, Qian Wu and Bao Lu
Materials 2021, 14(19), 5830; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14195830 - 05 Oct 2021
Cited by 5 | Viewed by 1566
Abstract
This paper presents a new modification of the nanostructure of CaSO4·2H2O crystals containing nanopores. This nanoporous structure was achieved in phosphogypsum samples that were modified by sodium carbonate and alum. The effects of sodium carbonate and alum on the [...] Read more.
This paper presents a new modification of the nanostructure of CaSO4·2H2O crystals containing nanopores. This nanoporous structure was achieved in phosphogypsum samples that were modified by sodium carbonate and alum. The effects of sodium carbonate and alum on the properties of phosphogypsum were studied. X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods were used to explore the micro-mechanism of the composite system. Subsequently, molecular dynamics simulations were used to study the nanopore structures of the modified CaSO4·2H2O. The results show that the addition of sodium carbonate and alum reduced the absolute dry density by 23.1% compared with the original phosphogypsum sample, with a bending strength of 2.1 MPa and compressive strength of 7.5 MPa. In addition, new hydration products, sodium sulfate and sodium aluminum sulfate, were formed in the sample doped with sodium carbonate and alum. A new nanostructure of CaSO4·2H2O crystal containing nanopores was formed. Molecular simulations show that the hydration products were responsible for the surface nanopore formation, which was the main factor leading to an increase in mechanical strength. The presented nanopore structure yields lightweight and high strength properties in the modified phosphogypsum. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Graphical abstract

13 pages, 3503 KiB  
Article
Study on the Preparation and Properties of Impervious and Breathable Sand Based on Hydrophobic Theory
by Xiao Li, Xiong Zhang and Hao Ren
Materials 2021, 14(19), 5613; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14195613 - 27 Sep 2021
Cited by 3 | Viewed by 1425
Abstract
Land desertification, a severe global ecological and environmental problem, brings challenges to the sustainable utilization of land resources in the world. The purpose of this research is to use hydrophobic theory to prepare impervious and breathable sand, and to solve the problems of [...] Read more.
Land desertification, a severe global ecological and environmental problem, brings challenges to the sustainable utilization of land resources in the world. The purpose of this research is to use hydrophobic theory to prepare impervious and breathable sand, and to solve the problems of sandy soil that seeps easily and makes it difficult for vegetation to survive in desertified areas. The influences of coating material content, first-level and second-level rough structure on the impermeability and air permeability of impervious and breathable sand were studied. The research showed that, with the increase in coating material content, the impervious performance of the sample increased firstly and then decreased, and the air permeability rose continuously. The hydrostatic pressure resistance of the sample can reach an extreme value of 53 mm. The first-level rough structure of micron structure can greatly improve the hydrophobic performance, thus improving the impervious performance. The addition of micron calcium carbonate would improve the hydrostatic pressure resistance height of the sample to 190 mm. The sample would reach a superhydrophobic state in the condition of a first-level rough structure of a nano structure built by nano silica, and the contact angle was up to 152.0°, so that the hydrostatic pressure resistance height can rise to 205 mm. The best performance would be achieved under the condition of relatively less raw material with a second-level rough structure of micro–nano. At this point, the contact angle of the sample reached 152.8° and the hydrostatic pressure resistance height was up to 205 mm. At the same time, the air permeability index of the above four kinds of impervious and breathable sand met all planting requirements. The sample prepared can satisfy the demands of different degrees of impermeability and air permeability, and can be widely used in desertification control. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

12 pages, 11545 KiB  
Article
Influence of Mineral Additives on the Efflorescence of Ettringite-Rich Systems
by Linglin Xu, Siyu Liu, Peiming Wang and Zhenghong Yang
Materials 2021, 14(18), 5464; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14185464 - 21 Sep 2021
Cited by 2 | Viewed by 1844
Abstract
Efflorescence is aesthetically undesirable to all cementitious materials products and mainly results from the carbonation of hydrates and salt precipitation. Alternative binders without portlandite formation theoretically have much lower efflorescence risk, but in practice, the efflorescence of ettringite-rich systems is still serious. This [...] Read more.
Efflorescence is aesthetically undesirable to all cementitious materials products and mainly results from the carbonation of hydrates and salt precipitation. Alternative binders without portlandite formation theoretically have much lower efflorescence risk, but in practice, the efflorescence of ettringite-rich systems is still serious. This study reports the impacts of mineral additives on the efflorescence of ettringite-rich systems and the corresponding microstructural evolution. The effects of silica fume, limestone powder, and diatomite on efflorescence and the capillary pore structure of mortars were investigated from a multi-scale analysis. The composition and microstructure of efflorescent phases were revealed by optical microscope (O.M.), in-situ Raman spectroscopy, and Scanning Electron Microscopy (SEM). Results indicate that the addition of mineral additives can efficiently inhibit the efflorescence of reference, especially with silica fume. Similar to the ettringite-rich system, the efflorescence substances of all modifies are composed of ettringite and CaCO3, indicating that the addition of mineral admixture does not lead to chemical reactions, lower capillary absorption coefficient of mineral additives modified specimen, the denser pore structure and the lower efflorescence degree. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

14 pages, 8387 KiB  
Article
The Failure Mechanisms of Precast Geopolymer after Water Immersion
by Shunfeng Wang, Long Yu, Linglin Xu, Kai Wu and Zhenghong Yang
Materials 2021, 14(18), 5299; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14185299 - 14 Sep 2021
Cited by 5 | Viewed by 2248
Abstract
Precast geopolymers with lower water/binder (0.14), which mainly consists of alkali solution, fly ash (FA) and steel slag (SS), were manufactured through molding pressing technology. The failure mechanisms of precast geopolymers after water immersion were studied by testing the loss of compressive strength, [...] Read more.
Precast geopolymers with lower water/binder (0.14), which mainly consists of alkali solution, fly ash (FA) and steel slag (SS), were manufactured through molding pressing technology. The failure mechanisms of precast geopolymers after water immersion were studied by testing the loss of compressive strength, the pH of the leaching solution, the concentration of ions (Na+, Ca2+, Si4+ and Al3+), the evolution of phases, pore structure and morphology, and further discussion of the regulation evolution was performed. The results show that the harmful pores (>50 nm) of geopolymers progressively decrease from 70% to 50% after 28 days of water immersion when the content of steel slag increases from 0 to 80 wt.%. Compressive strength of geopolymers sharply reduces in the first 3 days and then increases during the water immersion process, but the phase composition varies slightly. Furthermore, increasing the content of steel slag could decrease the total porosity and further prevent the water resistance. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

17 pages, 7278 KiB  
Article
Identification of Chemical Bonds and Microstructure of Hydrated Tricalcium Silicate (C3S) by a Coupled Micro-Raman/BSE-EDS Evaluation
by Zheyu Zhu, Zhongping Wang, Yue Zhou, Yuting Chen and Kai Wu
Materials 2021, 14(18), 5144; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14185144 - 08 Sep 2021
Cited by 7 | Viewed by 2174
Abstract
Identifying the phase evolution and revealing the chemical bonds of hydrated cements accurately is crucial to regulate the performance of cementitious materials. In this paper, a coupled Raman/BSE-EDS analysis was proposed to determine the chemical bonds of tricalcium silicate hydrates and the interface [...] Read more.
Identifying the phase evolution and revealing the chemical bonds of hydrated cements accurately is crucial to regulate the performance of cementitious materials. In this paper, a coupled Raman/BSE-EDS analysis was proposed to determine the chemical bonds of tricalcium silicate hydrates and the interface transition zone (ITZ) between inner C-S-H and anhydrates. The results show that the Raman/BSE-EDS method can accurately identify the chemical bonds of inner C-S-H and inner ITZ regions, which confirms the mixed structure of inner C-S-H and nano calcium hydroxide (CH). The inner ITZ shows a lattice change region with a thickness of 700–1000 nm, which can be attributed to the pre-disassembly process of C3S crystal. The successful application of coupled Raman/BSE-EDS provides new insight into the hydration process and multi-structure features of traditional cementitious materials. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

11 pages, 1251 KiB  
Article
A Comprehensive Study on the Hardening Features and Performance of Self-Compacting Concrete with High-Volume Fly Ash and Slag
by Zhenghong Yang, Sijia Liu, Long Yu and Linglin Xu
Materials 2021, 14(15), 4286; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14154286 - 31 Jul 2021
Cited by 8 | Viewed by 1509
Abstract
The main concern of this work is to evaluate the influences of supplementary cementitious materials (fly ash, slag) and a new type of polycarboxylate superplasticizer containing viscosity modifying agents (PCE-VMA) on the performance of self-compacting concrete (SCC). The workability, hydration process, mechanical property, [...] Read more.
The main concern of this work is to evaluate the influences of supplementary cementitious materials (fly ash, slag) and a new type of polycarboxylate superplasticizer containing viscosity modifying agents (PCE-VMA) on the performance of self-compacting concrete (SCC). The workability, hydration process, mechanical property, chloride permeability, degree of hydration and pore structure of SCC were investigated. Results indicate that the addition of fly ash and slag slows down early hydration and decreases the hydration degree of SCC, and thus leads to a decline in compressive strengths, especially within the first 7 days. The addition of slag refines pore structure and contributes to lower porosity, and thus the chloride permeability of SCC is decreased during the late hydration stage. Additionally, a new factor of calculated water–binder ratio is put forward, which can directly reflect the free water content of concrete mixture after mixing, and guide the mix proportion design of SCC. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

11 pages, 4027 KiB  
Article
Steel Corrosion Behavior of Reinforced Calcium Aluminate Cement-Mineral Additions Modified Mortar
by Zhongping Wang, Yuting Chen, Zheyu Zhu, Xiang Peng, Kai Wu and Linglin Xu
Materials 2021, 14(14), 4053; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14144053 - 20 Jul 2021
Cited by 3 | Viewed by 1859
Abstract
Mineral additions can eliminate the conversion in calcium aluminate hydrates and thus inhibit the future strength retraction of calcium aluminate cement (CAC). However, the impacts of these additions on the protection capacity of CAC concrete in relation to the corrosion of embedded steel [...] Read more.
Mineral additions can eliminate the conversion in calcium aluminate hydrates and thus inhibit the future strength retraction of calcium aluminate cement (CAC). However, the impacts of these additions on the protection capacity of CAC concrete in relation to the corrosion of embedded steel reinforcement remains unclear. This paper focused on the corrosion behavior of steel reinforcement in slag, limestone powder, or calcium nitrate-modified CAC mortars via XRD and electrochemical methods (corrosion potential, electrochemical impedance, and linear polarization evaluation). The results indicate that strätlingite (C2ASH8), which is formed in slag-modified CAC, has poor chloride-binding ability, leading to decline in corrosion resistance of the steel reinforcement. The electrochemical parameters of specimens immersed in NaCl solution suddenly drop at 14 days, which is 28 days earlier than that of the references. In contrast, the Ca2[Al(OH)6]20.5CO3OH·H2O (CaAl·CO32−-LDH) and 3CaO·Al2O3·Ca(NO3)2·12H2O (NO3-AFm) in limestone powder and calcium nitrate-modified CAC mortar show great chloride-binding ability, thereby improving the corrosion resistance of the steel reinforcement. The electrochemical parameters of specimens modified with calcium nitrate maintain a slow decreasing trend within 90 days. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

10 pages, 2689 KiB  
Article
Impacts of Space Restriction on the Microstructure of Calcium Silicate Hydrate
by Yue Zhou, Zhongping Wang, Zheyu Zhu, Yuting Chen, Linglin Xu and Kai Wu
Materials 2021, 14(13), 3645; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14133645 - 30 Jun 2021
Cited by 7 | Viewed by 1676
Abstract
The effect of hydration space on cement hydration is essential. After a few days, space restriction affects the hydration kinetics which dominate the expansion, shrinkage and creep of cement materials. The influence of space restriction on the hydration products of tricalcium silicate was [...] Read more.
The effect of hydration space on cement hydration is essential. After a few days, space restriction affects the hydration kinetics which dominate the expansion, shrinkage and creep of cement materials. The influence of space restriction on the hydration products of tricalcium silicate was studied in this paper. The microstructure, morphology and composition of calcium silicate hydrate (C-S-H) were explored from the perspective of a specific single micropore. A combination of Raman spectra, Fourier transform infrared spectra, scanning electron microscopy and energy dispersive X-ray spectroscopy were employed. The results show that space restriction affects the structure of the hydration products. The C-S-H formed in the micropores was mainly composed of Q3 silicate tetrahedra with a high degree of polymerization. The C-S-H formed under standard conditions with a water to cement ratio of 0.5 mostly existed as Q2 units. Space restriction during hydration is conducive to the formation of C-S-H with silica tetrahedra of a high polymerization degree, while the amount of water filling the micropore plays no obvious role on the polymeric structure of C-S-H during hydration. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

18 pages, 7243 KiB  
Article
Cyclic Behavior of Reinforced High Strain-Hardening UHPC under Axial Tension
by Jin-Ben Gu, Jun-Yan Wang and Yi-Qing Guo
Materials 2021, 14(13), 3602; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14133602 - 28 Jun 2021
Cited by 2 | Viewed by 1563
Abstract
The cyclic tensile behavior of steel-reinforced high strain-hardening ultrahigh-performance concrete (HSHUHPC) was investigated in this paper. In the experimental program, 12 HSHUHPC specimens concentrically placed in a single steel reinforcement under cyclic uniaxial tension were tested, accompanied by acoustic emission (AE) source locating [...] Read more.
The cyclic tensile behavior of steel-reinforced high strain-hardening ultrahigh-performance concrete (HSHUHPC) was investigated in this paper. In the experimental program, 12 HSHUHPC specimens concentrically placed in a single steel reinforcement under cyclic uniaxial tension were tested, accompanied by acoustic emission (AE) source locating technology, and 4 identical specimens under monotonic uniaxial tension were tested as references. The experimental variables mainly include the loading pattern, the diameter of the embedded steel rebar, and the level of target strain at each cycle. The tensile responses of the steel-reinforced HSHUHPC specimens were evaluated using multiple performance measures, including the failure pattern, load–strain response, residual strain, stiffness degradation, and the tension-stiffening behavior. The test results showed that the enhanced bond strength due to the inclusion of steel fibers transformed the failure pattern of the steel-reinforced HSHUHPC into a single, localized macro-crack in conjunction with a sprinkling of narrow and closely spaced micro-cracks, which intensified the strain concentration in the embedded steel rebar. Besides, it was observed that the larger the diameter of the embedded steel rebar, the smaller the maximum accumulative tensile strain under cyclic tension, which indicated that the larger the diameter of the embedded steel rebar, the greater the contribution to the tensile stiffness of steel-reinforced HSHUHPC specimens in the elastic–plastic stage. In addition, it was found that a larger embedded steel rebar appeared to reduce the tension-stiffening effect (peak tensile strength) of the HSHUHPC. Moreover, the residual strain and the stiffness of the steel-reinforced HSHUHPC were reduced by increasing the number of cycles and finally tended toward stability. Nevertheless, different target strain rates in each cycle resulted in different eventual cumulative tensile strain rates; hence the rules about failure pattern, residual strain, and loading stiffness were divergent. Finally, the relationship between the accumulative tensile strain and the loading stiffness degradation ratio under cyclic tension was proposed and the tension-stiffening effect was analyzed. Full article
(This article belongs to the Special Issue Corrosion, Properties and Characterization in Concrete)
Show Figures

Figure 1

Back to TopTop