Submit to Materials Review for Materials Propose a Special Issue

Journal Browser

► Journal Browser

Adsorption and Desorption Behavior for Rare Earth Metal Ions

Print Special Issue Flyer
Special Issue Editors
Special Issue Information
Keywords
Published Papers

A special issue of Materials (ISSN 1996-1944). This special issue belongs to the section "Materials Physics".

Deadline for manuscript submissions: closed (20 June 2022) | Viewed by 17398

Share This Special Issue

Special Issue Editors

Dr. Adina Negrea

E-Mail Website
Guest Editor

Faculty of Industrial Chemistry and Environmental Engineering, Politehnica University of Timisoara, 6 Vasile Parvan Bvd., 300223 Timisoara, Romania
Interests: adsorption; metal recovery; SEM; FT-IR
Special Issues, Collections and Topics in MDPI journals

Dr. Narcis Duteanu

E-Mail Website
Guest Editor

Faculty of Industrial Chemistry and Environmental Engineering, Politehnica University of Timisoara, 2 Piata Victoriei, RO 300006 Timisoara, Romania
Interests: adsorption; metal recovery; SEM; XRD; FT-IR

Special Issue Information

Dear Colleagues,

Rapid development of human society ove last hundred years has resulted in a sharp increase in the number and ammount of pollutants emitted into the environment, leading at severe imbalances. Simultaneously was observed a huge increase into the rare earth element usage. Broad diversification of industrial products used for improvement of our living conditions is responsible for most pollutant emissions. In this context, it is important to produce suitable materials (adsorbents, catalysts, and so on) to reduce the pollutant amount discharged into the environment. Most suitable technology used for rare earth metal recovery is represented by adsorption. In this context it is important to better understand rare earth metallic ions adsorption – desorption processes.

The topics of interest include, but are not limited to: adsorption, desorption, characterisation techniques, scannin electron microscopy, scanning probe, optical microscopy, X-Ray diffraction, FT-IR.

Dr. Adina Negrea
Dr. Narcis Duteanu
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Materials is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

adsoprtion / desoprtion
rare earth metals
SEM
XRD
FT-IR

Published Papers (9 papers)

Download All Papers

Research

18 pages, 5227 KiB

Open AccessArticle

Vanadium (V) Adsorption from Aqueous Solutions Using Xerogel on the Basis of Silica and Iron Oxide Matrix

by Florin Matusoiu, Adina Negrea, Mihaela Ciopec, Narcis Duteanu, Petru Negrea, Paula Ianasi and Cătălin Ianasi

Materials 2022, 15(24), 8970; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15248970 - 15 Dec 2022

Cited by 2 | Viewed by 1086

Abstract

Vanadium is considered a strategic metal with wide applications in various industries due to its unique chemical and physical properties. On the basis of these considerations, the recovery of vanadium (V) is mandatory because of the lack of raw materials. Various methods are used to recover vanadium (V) from used aqueous solutions. This study develops a clean and effective process for the recovery of vanadium (V) by using the adsorption method. At the same time, this study synthesizes a material starting from silica matrices and iron oxides, which is used as an adsorbent material. To show the phase composition, the obtained material is characterized by X-ray diffraction showing that the material is present in the amorphous phase, with a crystal size of 20 nm. However, the morphological texture of the material is determined by the N₂ adsorption–desorption method, proving that the adsorbent material has a high surface area of 305 m²/g with a total pore volume of 1.55 cm³/g. To determine the efficiency of the SiO₂Fe_xO_y material for the recovery of vanadium through the adsorption process, the role of specific parameters, such as the L-to-V ratio, pH, contact time, temperature, and initial vanadium concentration, must be evaluated. The adsorption process mechanism was established through kinetic, thermodynamic, and equilibrium studies. In our case, the process is physical, endothermic, spontaneous, and takes place at the interface of SiO₂Fe_xO_y with V₂O₅. Following equilibrium studies, the maximum adsorption capacity of the SiO₂Fe_xO_y material was 58.8 mg (V)/g of material. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

18 pages, 2457 KiB

Open AccessArticle

Indium Recovery by Adsorption on MgFe₂O₄ Adsorbents

by Loredana Ciocărlie, Adina Negrea, Mihaela Ciopec, Narcis Duteanu, Petru Negrea, Paula Ianasi, Catalin Ianasi and Nicoleta Sorina Nemes

Materials 2022, 15(20), 7054; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15207054 - 11 Oct 2022

Cited by 4 | Viewed by 1484

Abstract

Indium and its compounds have many industrial applications and are widely used in the manufacture of liquid crystal displays, semiconductors, low temperature soldering, and infrared photodetectors. Indium does not have its own minerals in the Earth’s crust, and most commonly, indium is associated with the ores of zinc, lead, copper and tin. Therefore, it must be recovered as a by-product from other metallurgical processes or from secondary raw materials. The aim of this study is to investigate the adsorption properties for recovering indium from aqueous solutions using iron–magnesium composite (MgFe₂O₄). In addition, the results show that the material offers very efficient desorption in 15% HCl solution, being used for 10 adsorption–desorption cycle test. These results provide a simple and effective process for recovering indium. Present study was focuses on the synthesis and characterization of the material by physico-chemical methods such as: X-ray diffraction, FT-IR spectroscopy, followed by the adsorption tests. The XRD indicates that the MgFe₂O₄ phase was obtained, and the crystallite size was about 8 nm. New prepared adsorbent materials have a point of zero charge of 9.2. Studies have been performed to determine the influence of pH, initial indium solution concentration, material/solution contact time and temperature on the adsorption capacity of the material. Adsorption mechanism was established by kinetic, thermodynamic and equilibrium studies. At equilibrium a maximum adsorption capacity of 46.4 mg/g has been obtained. From kinetic and thermodynamic studies was proved that the studied adsorption process is homogeneous, spontaneous, endothermic and temperature dependent. Based on Weber and Morris model, we can conclude that the In (III) ions takes place at the MgFe₂O₄/In (III) solution–material interface. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

23 pages, 4373 KiB

Open AccessArticle

Silica- Iron Oxide Nanocomposite Enhanced with Porogen Agent Used for Arsenic Removal

by Georgiana Mladin, Mihaela Ciopec, Adina Negrea, Narcis Duteanu, Petru Negrea, Paula Ianasi and Cătălin Ianași

Materials 2022, 15(15), 5366; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15155366 - 04 Aug 2022

Cited by 14 | Viewed by 1390

Abstract

This study aims to remove arsenic from an aqueous medium by adsorption on a nanocomposite material obtained by the sol–gel method starting from matrices of silica, iron oxide and NaF (SiO₂/Fe(acac)₃/NaF). Initially, the study focused on the synthesis and characterization of the material by physico–chemical methods such as: X-ray diffraction, FT-IR spectroscopy, Raman spectroscopy, atomic force microscopy, and magnetization. Textural properties were obtained using nitrogen adsorption/desorption measurements. The zero load point, pHpZc, was also determined by the method of bringing the studied system into equilibrium. In addition, this study also provides a comprehensive discussion of the mechanism of arsenic adsorption by conducting kinetic, thermodynamic and equilibrium studies. Studies have been performed to determine the effects of adsorbent dose, pH and initial concentration of arsenic solution, material/arsenic contact time and temperature on adsorption capacity and material efficiency. Three theoretical adsorption isotherms were used, namely Langmuir, Freundlich and Sips, to describe the experimental results. The Sips isotherm was found to best describe the experimental data obtained, the maximum adsorption capacity being ~575 µg As(III)/g. The adsorption process was best described by pseudo-second order kinetics. Studies have been performed at different pH values to establish not only the optimal pH at which the adsorption capacity is maximum, but also which is the predominantly adsorbed species. The effect of pH and desorption studies have shown that ion exchange and the physiosorption mechanism are implicated in the adsorption process. From a thermodynamic point of view, parameters such as ΔG°, ΔH° and ΔS° were evaluated to establish the mechanism of the adsorption process. Desorption studies have been performed to determine the efficiency of the material and it has been shown that the material can be used successfully to treat a real-world example of deep water with a high arsenic content. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

25 pages, 6828 KiB

Open AccessArticle

Rare Earth Group Separation after Extraction Using Sodium Diethyldithiocarbamate/Polyvinyl Chloride from Lamprophyre Dykes Leachate

by Eman M. Allam, Taysser A. Lashen, Saeyda A. Abou El-Enein, Mohamed A. Hassanin, Ahmed K. Sakr, Mohamed F. Cheira, Aljawhara Almuqrin, Mohamed Y. Hanfi and M. I. Sayyed

Materials 2022, 15(3), 1211; https://0-doi-org.brum.beds.ac.uk/10.3390/ma15031211 - 05 Feb 2022

Cited by 17 | Viewed by 2787

Abstract

This study presents the first application of sodium diethyldithiocarbamate/polyvinyl chloride (DdTC/PVC) as a novel adsorbent for rare earth element (REE) sorption from leach liquors. DdTC/PVC has higher adsorption properties than other sorbents, the synthesis of DdTC/PVC is more accessible than other resins, and it is considered a more affordable sorbent. The three-liquid-phase extraction technique (TLPE) was applied to separate REEs into light, middle, and heavy rare earth elements as groups. The TLPE is an excellent achievable technique in the separation of REEs. DdTC/PVC was prepared as a sorbent to sorb rare-earth ions in chloride solution. It was described by XRD, SEM, TGA, and FTIR. The factors pH, initial rare-earth ion concentration, contact time, and DdTC/PVC dose were also analyzed. The ideal pH was 5.5, and the ideal equilibration time was found to be 45 min. The rare-earth ion uptake on DdTC/PVC was 156.2 mg/g. The rare-earth ion sorption on DdTC/PVC was fitted to Langmuir and pseudo-2nd-order models. The rare-earth ions’ thermodynamic adsorption was spontaneous and exothermic. In addition, rare-earth ion desorption from the loaded DdTC/PVC was scrutinized using 1 M HCl, 45 min time of contact, and a 1:60 S:L phase ratio. The obtained rare earth oxalate concentrate was utilized after dissolving it in HCl to extract and separate the RE ions into three groups—light (La, Ce, Nd, and Sm), middle (Gd, Ho, and Er), and heavy (Yb, Lu, and Y)—via three-liquid-phase extraction (TLPE). This technique is simple and suitable for extracting REEs. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

15 pages, 3915 KiB

Open AccessArticle

Kinetics, Thermodynamics and Equilibrium Studies for Gold Recovery from Diluted Waste Solution

by Adina Negrea, Sylwia Ronka, Mihaela Ciopec, Narcis Duteanu, Petru Negrea and Maria Mihailescu

Materials 2021, 14(18), 5325; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14185325 - 15 Sep 2021

Cited by 3 | Viewed by 1729

Abstract

2,2′-thiobisethanol dimethacrylate/ethylene glycol dimethacrylate copolymer (coP-TEDMA/EGDMA) was used as a sorbent for gold recovery from residual solutions resulting from the electroplating industry. Firstly, synthesized material was characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, and confocal laser scanning microscopy. The sorption process mechanism was evidenced on the basis of kinetic, thermodynamic and equilibrium studies. To highlight this, the influence of solution pH, temperature and gold initial concentration on maximum sorption capacity was studied. The obtained experimental data were modeled using Langmuir, Freundlich and Sips sorption isotherms, and it was observed that the Sips one was better for describing the studied sorption process. Kinetic data were fitted using pseudo-first-order and pseudo-second-order kinetic models. Of these models, the studied process was better described by the pseudo-second-order model. The thermodynamic parameters free Gibbs energy (ΔG0), enthalpy (ΔH0), and entropy (ΔS0) were evaluated on the basis of the van’t Hoff equation. On the basis of the thermodynamic study, it was concluded that gold recovery on coP-TEDMA/EGDMA is a spontaneous and endothermic process. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

16 pages, 3550 KiB

Open AccessArticle

A Green, Simple and Facile Way to Synthesize Silver Nanoparticles Using Soluble Starch. pH Studies and Antimicrobial Applications

by Bogdan Pascu, Adina Negrea, Mihaela Ciopec, Narcis Duteanu, Petru Negrea, Nicoleta Sorina Nemeş, Corina Seiman, Eleonora Marian and Otilia Micle

Materials 2021, 14(16), 4765; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14164765 - 23 Aug 2021

Cited by 9 | Viewed by 2707

Abstract

Along with the progress of nanoscience and nanotechnology came the means to synthesize nanometric scale materials. While changing their physical and chemical properties, they implicitly changed their application area. The aim of this paper was the synthesis of colloidal silver nanoparticles (Ag-NPs by ultrasonic disruption), using soluble starch as a reducing agent and further as a stabilizing agent for produced Ag-NPs. In this context, an important parameter for Ag-NPs preparation is the pH, which can determine the particle size and stability. The physical-chemical behavior of the synthesized Ag-NPs (shape, size, dispersion, electric charge) is strongly influenced by the pH value (experiment being conducted for pH values in the range between 8 and 13). The presence of a peak located at 412 nm into the UV-VIS spectra demonstrates the presence of silver nano-spheres into the produced material. In UV/VIS spectra, we observed a specific peak for yellow silver nano-spheres located at 412 nm. Samples characterization was performed by scanning electron microscopy, SEM, energy-dispersive X-ray spectroscopy, EDX, Fourier-transform infrared spectroscopy, and FT-IR. For all Ag-NP samples, we determined the zeta and observed that the Ag-NP particles obtained at higher pH and have better stability. Due to the intrinsic therapeutic properties and broad antimicrobial spectrum, silver nanoparticles have opened new horizons and new approaches for the control of different types of infections and wound healing abilities. In this context, the present study also aims to confirm the antimicrobial effect of prepared Ag-NPs against several bacterial strains (indicator and clinically isolated strains). In this way, it was confirmed that the antimicrobial activity of synthesized Ag-NPs was good against Staphylococcus aureus (ATCC 25923 and S. aureus MSSA) and Escherichia coli (ATTC 25922 and clinically isolated strain). Based on this observation, we conclude that the prepared Ag-NPs can represent an alternative or auxiliary material used for controlling important nosocomial pathogens. The fungal reference strain Candida albicans was more sensitive at Ag-NPs actions (zone of inhibition = 20 mm) compared with the clinically isolated strain (zone of inhibition = 10 mm), which emphasizes the greater resistance of fungal strains at antimicrobial agent’s action. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

20 pages, 4337 KiB

Open AccessArticle

Testing of Chemically Activated Cellulose Fibers as Adsorbents for Treatment of Arsenic Contaminated Water

by Mihaela Ciopec, Gabriela Biliuta, Adina Negrea, Narcis Duțeanu, Sergiu Coseri, Petru Negrea and Makarand Ghangrekar

Materials 2021, 14(13), 3731; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14133731 - 02 Jul 2021

Cited by 18 | Viewed by 1996

Abstract

Exposure to different arsenic concentrations (higher than 10 μg/L), either due to the direct consumption of contaminated drinking water or indirectly by using contaminated food is harmful for human health. Therefore, it is important to remove arsenic from aqueous solutions. Among many arsenic removal technologies, adsorption offers a promising solution with a good efficiency, however the material used as adsorbent play a very vital role. The present investigation evaluated the behavior of two cellulose-based adsorbent materials, i.e., viscose fibers (V) and its TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl) derivative, obtained by using the well-established TEMPO-mediated protocol (VF). Due to the known arsenic affinity for Fe ions the two materials were later doped with it. This was done after a preliminary functionalization with di-2-ethylhexyl phosphoric acid (DEHPA), to obtain two materials: V-DEHPA-Fe and VF-DEHPA-Fe. Arsenic adsorption is known to be pH dependent (between 6 and 8); therefore, the optimal pH range for As(V) adsorption has been established. In order to evaluate the adsorption mechanism for both the synthesized materials, the influence of contact time, temperature and initial concentration was evaluated. Langmuir, Freundlich and Sips equilibrium isotherm models were used in order to determine the ability of the model to describe As(V) adsorption process. The maximum adsorption capacity of the material V-DEHPA-Fe was 247.5 µg As(V)/g with an As(V) initial concentration of 5 mg/L and for the material VF-DEHPA-Fe it was 171.2 µg As(V)/g with initial concentration of 5 mg/L. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

16 pages, 2725 KiB

Open AccessArticle

Evaluation of Performance of Functionalized Amberlite XAD7 with Dibenzo-18-Crown Ether-6 for Palladium Recovery

by Oana Alexandra Grad, Mihaela Ciopec, Adina Negrea, Narcis Duteanu, Petru Negrea and Raluca Vodă

Materials 2021, 14(4), 1003; https://0-doi-org.brum.beds.ac.uk/10.3390/ma14041003 - 20 Feb 2021

Cited by 13 | Viewed by 1633

Abstract

Due to the increased demand for palladium, as well due to its reduced availability in nature, its recovery from diluted waste solutions becomes a necessity, and perhaps an emergency. As a result of economic and technological development, new materials with improved adsorbent properties that are more efficient for metallic ions’ recovery were synthesized and introduced to market. The goal of this study was to obtain a new adsorbent material by functionalizing through impregnation a commercial polymeric support that was both inexpensive and environmentally friendly (Amberlite XAD7) with crown ether (di-benzo-18-crown-6—DB18C6). Crown ethers are known for their ability to form complexes within metallic ions, by including them inside of the ring, regardless of its atomic size. Adsorbent material was prepared by impregnation using the solvent-impregnated resin method (SIR). To highlight the presence of crown ether on the resin surface, a new synthesized material was characterized by scanning electron microscopy (SEM), elemental analysis X-ray energy dispersive spectroscopy (EDX) and Fourier transform infrared spectroscopy (FT-IR). The specific surface of the adsorbent material was also determined by the Brunauer–Emmett–Teller (BET) method. Adsorbent performances of the prepared material were highlighted by kinetic, thermodynamic and equilibrium studies and a possible mechanism was also proposed. The influence of specific parameters for the adsorption process (contact time, temperature, Pd(II) initial concentration) on the maximum adsorption capacity was pursued. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

16 pages, 3603 KiB

Open AccessArticle

Kinetics and Thermodynamics Studies for Cadmium (II) Adsorption onto Functionalized Chitosan with Hexa-Decyl-Trimethyl-Ammonium Chloride

by Cristina Ardean, Mihaela Ciopec, Corneliu Mircea Davidescu, Petru Negrea and Raluca Voda

Materials 2020, 13(23), 5552; https://0-doi-org.brum.beds.ac.uk/10.3390/ma13235552 - 05 Dec 2020

Viewed by 1309

Abstract

A new adsorbent material was obtained by functionalization of chitosan with hexa-decyl-trimethyl-ammonium chloride and tested as an adsorbent for Cd(II) ions. Functionalization is due to the desire to improve the adsorbent properties of the biopolymer used for removal of metallic ions. Obtained material was characterized by FTIR (Fourier Transform InfraRed spectroscopy), SEM (Scanning Electron Microscopy) and EDX (Energy dispersive X-ray Spectroscopy). To prove the Cd(II) adsorption mechanism, we performed adsorption tests determining influence of biopolymer ratio, pH, contact time, temperature and Cd(II) initial concentration. Obtained experimental data were modeled using two kinetics models: pseudo-first-order and pseudo-second-order models. Cd(II) adsorption kinetics was better described by pseudo-second-order model. Further, experimental data were fitted using three different adsorption isotherms: Langmuir, Freundlich and Sips. The studied adsorption process is well described by the Sips adsorption isotherm, when the maximum adsorption capacity value is near the experimental one. Likewise, we evaluated the values of thermodynamic parameters which indicate that the studied process is an endothermic and spontaneous one, being a physical adsorption. Prepared adsorbent materials have a maximum adsorption capacity of 204.3 mg Cd²⁺ per gram at pH > 4.0 and 298 K. In addition, this material was reused for Cd²⁺ recovery for 20 times. Full article

(This article belongs to the Special Issue Adsorption and Desorption Behavior for Rare Earth Metal Ions)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Adsorption and Desorption Behavior for Rare Earth Metal Ions

Share This Special Issue

Special Issue Editors

Special Issue Information

Keywords

Published Papers (9 papers)

Research

Further Information

Guidelines

MDPI Initiatives

Follow MDPI