We demonstrate in this work that expanded graphite (EG) can lead to a very large enhancement in thermal conductivity of polyetherimide−graphene and epoxy−graphene nanocomposites prepared via solvent casting technique. A k value of 6.6 W$\cdot$m⁻¹$\cdot$K⁻¹ is achieved for 10 wt% composition sample, representing an enhancement of ~2770% over pristine polyetherimide (k~0.23 W$\cdot$m⁻¹$\cdot$K⁻¹). This extraordinary enhancement in thermal conductivity is shown to be due to a network of continuous graphene sheets over long−length scales, resulting in low thermal contact resistance at bends/turns due to the graphene sheets being covalently bonded at such junctions. Solvent casting offers the advantage of preserving the porous structure of expanded graphite in the composite, resulting in the above highly thermally conductive interpenetrating network of graphene and polymer. Solvent casting also does not break down the expanded graphite particles due to minimal forces involved, allowing for efficient heat transfer over long−length scales, further enhancing overall composite thermal conductivity. Comparisons with a recently introduced effective medium model show a very high value of predicted particle–particle interfacial conductance, providing evidence for efficient interfacial thermal transport in expanded graphite composites. Field emission environmental scanning electron microscopy (FE−ESEM) is used to provide a detailed understanding of the interpenetrating graphene−polymer structure in the expanded graphite composite. These results open up novel avenues for achieving high thermal conductivity polymer composites. Full article

The high thermal conductivity and good insulating properties of boron nitride (BN) make it a promising filler for high-performance polymer-based thermal management materials. An easy way to prepare BN-polymer composites is to directly mix BN particles with polymer matrix. However, a high concentration of fillers usually leads to a huge reduction of mechanical strength and optical transmission. Here, we propose a novel method to prepare polyethylene/boron nitride nanoplates (PE/BNNPs) composites through the combination of electrostatic self-assembly and hot pressing. Through this method, the thermal conductivity of the PE/BNNPs composites reach 0.47 W/mK, which gets a 14.6% improvement compared to pure polyethylene film. Thanks to the tight bonding of polyethylene with BNNPs, the tensile strength of the composite film reaches 1.82 MPa, an increase of 173.58% compared to that of pure polyethylene film (0.66 MPa). The fracture stress was also highly enhanced, with an increase of 148.44% compared to pure polyethylene film. Moreover, the addition of BNNPs in PE does not highly reduce its good transmittance, which is preferred for thermal management in devices like light-emitting diodes. This work gives an insight into the preparation strategy of transparent and flexible thermal management materials with high thermal conductivity. Full article

The rapid development of chip technology has all put forward higher requirements for highly thermally conductive materials. In this work, a new type of material of Fishbone-like silicon carbide (SiC) material was used as the filler in a polyvinylidene fluoride (PVDF) matrix. The silicon carbide/polyvinylidene fluoride (SiC/PVDF) composites were successfully prepared with different loading by a simple mixing method. The thermal conductivity of SiC/PVDF composite reached 0.92 W m⁻¹ K⁻¹, which is 470% higher than that of pure polymer. The results show that using the filler with a new structure to construct thermal conductivity networks is an effective way to improve the thermal conductivity of PVDF. This work provides a new idea for the further application in the field of electronic packaging. Full article

In this paper, we report a thermal conductive polymer composite that consists of silicone rubber (SR) and branched Al₂O₃ (B-Al₂O₃). Owing to the unique two-dimensional branched structure, B-Al₂O₃ particles form a continuous three-dimensional network structure by overlapping each other in the matrix, serving as a continuous heat conductive pathway. As a result, the polymer composite with a 70 wt% filler achieves a maximum thermal conductivity of 1.242 Wm⁻¹ K⁻¹, which is equivalent to a significant enhancement of 521% compared to that of a pure matrix. In addition, the composite maintains a high volume resistivity of 7.94 × 10¹⁴ Ω·cm with the loading of 70 wt%, indicating that it meets the requirements in the field of electrical insulation. Moreover, B-Al₂O₃ fillers are well dispersed (no large agglomerates) and form a strong interfacial adhesion with the matrix. Therefore, the thermal decomposition temperature, residual mass, tensile strength, modulus and modulus of toughness of composites are significantly improved simultaneously. This strategy provides new insights for the design of high-performance polymer composites with potential application in advanced thermal management in modern electronics. Full article

Dielectric materials with excellent thermally conductive and mechanical properties can enable disruptive performance enhancement in the areas of advanced electronics and high-power devices. However, simultaneously achieving high thermal conductivity and mechanical strength for a single material remains a challenge. Herein, we report a new strategy for preparing mechanically strong and thermally conductive composite films by combining aramid nanofibers (ANFs) with graphene oxide (GO) and edge-hydroxylated boron nitride nanosheet (BNNS-OH) via a vacuum-assisted filtration and hot-pressing technique. The obtained ANF/GO/BNNS film exhibits an ultrahigh in-plane thermal conductivity of 33.4 Wm⁻¹ K⁻¹ at the loading of 10 wt.% GO and 50 wt.% BNNS-OH, which is 2080% higher than that of pure ANF film. The exceptional thermal conductivity results from the biomimetic nacreous “brick-and-mortar” layered structure of the composite film, in which favorable contacting and overlapping between the BNNS-OH and GO is generated, resulting in tightly packed thermal conduction networks. In addition, an outstanding tensile strength of 93.3 MPa is achieved for the composite film, owing to the special biomimetic nacreous structure as well as the strong π−π interactions and extensive hydrogen bonding between the GO and ANFs framework. Meanwhile, the obtained composite film displays excellent thermostability (T_d = 555 °C, T_g > 400 °C) and electrical insulation (4.2 × 10¹⁴ Ω·cm). We believe that these findings shed some light on the design and fabrication of multifunctional materials for thermal management applications. Full article

The development of high thermally conductive polymer composites with low filler content remains challenging in the field of thermal interface materials (TIMs). Herein, we fabricated a series of flexible fiber membranes (TMMFM) with high thermally conductive based on thermoplastic polyurethane (TPU) and acidified multiwalled carbon nanotubes (a-MWCNTs) via electrospinning and ultrasonic anchoring method. The SEM and TEM results demonstrated that the a-MWCNTs aligned along the fiber orientation in the membrane and anchored on the membrane surface strongly, which can establish the heat conduction path both in the horizontal and vertical directions. With the incorporation of 10 wt% a-MWCNTs, the horizontal direction (λ_∥) and vertical direction (λ_⊥) thermal conductivity value of TMMFM-5 was 3.60 W/mK and 1.79 W/mK, respectively, being 18 times and 10 times higher compared to pure TPU fiber membranes. Furthermore, the TMMFM maintained favorable flexibility of the TPU matrix because the small amount of a-MWCNTs only slightly hinders the mobility of the TPU molecular chain. The performance of the obtained TMMFM unveils their potential as a promising choice of flexible TIMs. Full article

Polymer-based composites with high thermal conductivity and dielectric breakdown strength have gained increasing attention due to their significant application potential in both power electronic devices and power equipment. In this study, we successfully prepared novel sandwich AlN/epoxy composites with various layer thicknesses, showing simultaneously and remarkably enhanced dielectric breakdown strength and thermal conductivity. The most optimized sandwich composite, with an outer layer thickness of 120 μm and an inner layer thickness of 60 μm (abbreviated as 120-60) exhibits a high through-plane thermal conductivity of 0.754 W/(m·K) (4.1 times of epoxy) and has a dielectric breakdown strength of 69.7 kV/mm, 8.1% higher compared to that of epoxy. The sandwich composites also have higher in-plane thermal conductivity (1.88 W/(m·K) for 120-60) based on the novel parallel models. The sandwich composites with desirable thermal and electrical properties are very promising for application in power electronic devices and power equipment. Full article

Advancements in technology related to energy systems, such as heat exchangers, electronics, and batteries, are associated with the generation of high heat fluxes which requires appropriate thermal management. Presently, conventional thermal fluids have found limited application owing to low thermal conductivity (TC). The need for more efficient fluids has become apparent leading to the development of nanofluids as advanced thermal fluids. Nanofluid synthesis by suspending nano-size materials into conventional thermal fluids to improve thermal properties has been extensively studied. TC is a pivotal property to the utilization of nanofluids in various applications as it is strongly related to improved efficiency and thermal performance. Numerous studies have been conducted on the TC of nanofluids using diverse nanoparticles and base fluids. Different values of TC enhancement have been recorded which depend on various factors, such as nanoparticles size, shape and type, base fluid and surfactant type, temperature, etc. This paper attempts to conduct a state-of-the-art review of the TC enhancement of metal oxide nanofluids owing to the wide attention, chemical stability, low density, and oxidation resistance associated with this type of nanofluid. TC and TC enhancements of metal oxide nanofluids are presented and discussed herein. The influence of several parameters (temperature, volume/weight concentration, nano-size, sonication, shape, surfactants, base fluids, alignment, TC measurement techniques, and mixing ratio (for hybrid nanofluid)) on the TC of metal oil nanofluids have been reviewed. This paper serves as a frontier in the review of the effect of alignment, electric field, and green nanofluid on TC. In addition, the mechanisms/physics behind TC enhancement and techniques for TC measurement have been discussed. Results show that the TC enhancement of metal oxide nanofluids is affected by the aforementioned parameters with temperature and nanoparticle concentration contributing the most. TC of these nanofluids is observed to be actively enhanced using electric and magnetic fields with the former requiring more intense studies. The formulation of green nanofluids and base fluids as sustainable and future thermal fluids is recommended. Full article