A Case Study of Waste Scrap Tyre-Derived Carbon Black Tested for Nitrogen, Carbon Dioxide, and Cyclohexane Adsorption

Abstract

Waste scrap tyres were thermally decomposed at the temperature of 600 °C and heating rate of 10 °C·min⁻¹. Decomposition was followed by the TG analysis. The resulting pyrolytic carbon black was chemically activated by a KOH solution at 800 °C. Activated and non-activated carbon black were investigated using high pressure thermogravimetry, where adsorption isotherms of N₂, CO₂, and cyclohexane were determined. Isotherms were determined over a wide range of pressure, 0.03–4.5 MPa for N₂ and 0.03–2 MPa for CO₂. In non-activated carbon black, for the same pressure and temperature, a five times greater gas uptake of CO₂ than N₂ was determined. Contrary to non-activated carbon black, activated carbon black showed improved textural properties with a well-developed irregular mesoporous-macroporous structure with a significant amount of micropores. The sorption capacity of pyrolytic carbon black was also increased by activation. The uptake of CO₂ was three times and for cyclohexane ten times higher in activated carbon black than in the non-activated one. Specific surface areas evaluated from linearized forms of Langmuir isotherm and the BET isotherm revealed that for both methods, the values are comparable for non-activated carbon black measured by CO₂ and for activated carbon black measured by cyclohexane. It was found out that the N₂ sorption capacity of carbon black depends only on its specific surface area size, contrary to CO₂ sorption capacity, which is affected by both the size of specific surface area and the nature of carbon black.

1. Introduction

Due to their excellent properties, polymers have become irreplaceable in our lives, and their production and consumption is growing year by year. As a consequence, the amount of waste polymers produced is growing as well. When it comes to environmental protection and sustainable development, upgrading polymer waste to usable material is a key issue. Unfortunately, waste disposal and polymer-based waste incineration still remain the most common ways of dealing with problems regarding potentially hazardous material disposal today [1] of this waste.

In our industrial world, approximately one scrap tyre (ST) is produced per person every year [2]. It means that in the European Union 15 million tons of ST are disposed of every year. This rapid trend, along with the fact that the majority of these tyres are stockpiled in landfills, presents one of the greatest. For this reason, great attention is currently being paid to ST pyrolysis.

Pyrolysis may be a prospective way of reducing the amount of ST, or even of converting them into valuable material. Generally speaking, pyrolysis is thermal degradation (without oxygen), which yields solid, liquid, and gas products that may be further used. Typical yields of ST pyrolysis depend on process conditions (temperature, heating rate, and inert gas flow rate) and used facilities, and are as follows: 33–38 wt% of solid product, 38–55 wt% of liquid product, and 10–30 wt% of gas product [3]. The pyrolysis process is widely used, producing a solid residue with enhanced properties, the so-called pyrolytic carbon black (CBp). As a raw material, ST consists of fewer chemical components, has greater gross calorific value than coal [4], and is widely available, cheap, and suitable for recycling as a material rich in carbon.

The CBp produced by ST pyrolysis could become a marketable and commercially usable product, as long as its properties are similar to the manufactured carbon blacks (CBs). CBp produced by pyrolysis of waste ST can be used in many different ways, e.g., as sorbents, pigments, in rubber or battery production, etc. [5,6,7,8,9,10].

Adsorption is coming to be regarded as a practicable separation method for purification or bulk separation in newly developed material production processes, e.g., high-tech materials and biochemical and biomedical products. Surface characteristics and pore structures of adsorbents are the main properties in determining adsorption equilibrium and rate properties, which are needed for plant design. New adsorbents are being developed all the time, introducing new applications for adsorption technology [6,11].

One of the methods suitable for adsorption measurement and characterization of specific surface area is the gravimetric sorption method of gas sorption. The principle of this method [12] consists of exact measurements of mass difference at constant pressure steps and constant temperature. Gravimetric methods are great at high precision and sensitivity, which allow the thermogravimeter TGA-HP50. This apparatus employs a high-sensitivity balance with 5 g capacity and enables the measurement of a variety of gas compositions at a measurement temperature up to 800 °C and low- (vacuum) and high-pressure (15 MPa) at a static or dynamic flow regime.

The chemical treatment of CBp is one of the commonly used methods to modify and improve the functionality, pore structure, and surface area of carbonaceous materials. The chemical treatment process can alter the properties of carbonaceous materials (e.g., functional group, surface area, pore volume, and elemental composition) and increase its performance [13]. One common and inexpensive chemical used for the chemical treatment of carbonaceous materials is KOH, which was studied in many articles [14,15,16]. In all cases of carbon black activation by KOH, textural properties and adsorption capacity were improved [17,18,19].

This paper is a follow-up to an earlier article [20], which focused on ST and pyrolytic CBp characterization by means of thermogravimetry and spectroscopy, and on estimating optimal pyrolysis parameters. This paper, in turn, deals with:

• The activation of CBp prepared under the above-mentioned conditions (pyrolysis at 600 °C, heating rate of 10 °C·min⁻¹), in order to achieve improvement in textural properties. Due to its great ability to improve porosity, KOH was selected as an activating agent.
• Evaluation of sorption capacity by means of gravimetric method of gas sorption for two gases, i.e., N₂ and CO₂, at a high relative pressure, and sorption capacity for pure cyclohexane vapor at a low relative pressure were both investigated. N₂ was chosen as a reference gas. CO₂ is a representative greenhouse gaseous pollutant in the air, contributing to global warming [21]. Cyclohexane is a representative waste non-polar VOC solvent from the chemical industry [22].
• Determination of specific surface area of CBp and CBa by adsorption of N₂, CO₂, and cyclohexane at specific experimental conditions using the sorption gravimetric method at the constant pressure. Primary data were treated by the model of Langmuir isotherms and evaluated parameters were used for specific surface area calculation.

The results of our investigation could be a useful resource for academia and the industry to deal with sorbents prepared from waste polymers for gaseous air pollutants applications.

2. Results and Discussion

2.1. Material Characterization

STs are composed of moisture (0.7 wt%), volatiles (62 wt%), fixed carbon (33 wt%), and ash (4 wt%) and the STs gross calorific have a value of 38,034 J·g⁻¹ [20]. By elemental analysis, it was determined that carbon black contains 85.3% C, 0.3% H₂, 0.3% N₂, 2.3% S, and 6.8% O₂. The most common types of rubber used in scrap tyres are natural, butadiene, and styrene-butadiene rubber. STs also contain a relatively small amount of oil, plasticiser (contains silicon), and metals, for example zinc [23]. Compared to other activated carbon precursors (e.g., coal, wood), STs have a lower ash and fixed carbon content [24].

The course of ST pyrolysis is documented in TG and DTG curves in Figure 1. The TG curve with a typical S-curve is shown in Figure 1a. The TG curve did not reach a zero value but only ~40 wt%. Approximately 60 wt% of volatiles are released from the sample of ST that corresponds to ~62 wt% of volatiles measured by proximate analysis and data from literature sources [24]. First, derivation of the TG curve (DTG curves) is shown in Figure 1b. From Figure 1b, it is obvious that the pyrolysis of ST starts at ~220 °C and the whole process is finished at ~500 °C. The total weight loss was again ~60 wt%. The pyrolysis of ST proceeded in two stages (Figure 1b). First, the peak was reached at ~300 °C and corresponds to the vaporization of oils, plasticizers, and additives. Second, the peak was reached at 440 °C and it refers to the rubber decomposition (natural, butadiene, and styrene-butadiene rubber). The particle, after being totally pyrolyzed, contained only fixed carbon black and inorganic matter.

Raman spectra of the CBp, CBa, and original ST reflect their structural order (Figure 2). As the Raman spectroscopy is a surface sensitive method, the Raman spectra of the ST sample, measured repeatedly on separated spots, do not reflect the presence of carbon black due to the not sufficiently high concentration of the carbon particles in the surface layer. The particles of the carbon black in the original ST material are evenly distributed and embedded in the rubber matrix.

The main Raman bands revealed in the spectra of both CBp and CBa are G-band at 1590 cm⁻¹, “graphitic”, which is connected with the C=C stretching vibrations of any pair of sp2 sites, and D-band at 1355 cm⁻¹, “disorder” band assigned to the breathing vibration of the aromatic rings, whose symmetry is broken due to their proximity to the edge of a graphite sheet, or presence of a heteroatom [25]. The Raman spectra of the CBa and CBp are virtually unchanged. The calculated ratio of areas I of the G and D bands is comparable for both carbon blacks (value I_D/I_G for CBp is 1.88 and for CBa is 1.81). Thus, the activation process does not influence the carbonaceous structure of the carbon black itself. Detailed parameters of Raman peaks were published earlier in [20].

Textural properties of original ST, CBp, and CBa defined from the nitrogen and krypton physisorption measurements are documented in

Table 1. Textural properties of original scrap tyre and produced carbon blacks.

	SBET	Smeso	Vmicro	Vtotal	Vmicro	Vtotal
	/m2·g−1		/mm3lig·g−1		/cm3(STP)·g−1
ST *	0.13	0	0	0	0	0
CBp	88	56	17	691	11	447
CBa	644	265	211	1186	136	767

* The specific surface area of the material was determined by Kr physisorption at 77 K. S_meso: Mesopore surface area; V_micro: Micropore volume; V_total: Total pore volume.

. The progress of N₂ adsorption-desorption isotherms and evaluated pore-size distributions of studied CBp and CBa are illustrated in Figure 3 and Figure 3b, respectively.

From Table 1, it is obvious that the original ST is nonporous and possesses a very low S_BET (~0.13 m².g⁻¹). Contrary to that, the shapes of N₂ adsorption-desorption isotherms with hysteresis loops of produced CBp and CBa basically correspond to types II and IV+I, respectively, according to the IUPAC classification [26]. This suggests porous properties of both produced samples. CBp shows the developed predominantly macroporous structure (Figure 3b), having the S_BET of 88 m²·g⁻¹. Contrary to CBp, the CBa shows, besides the irregular mesoporous-macroporous structure, also a significant amount of micropores. This feature of CBa matches its substantially improved textural properties, compared to CBp (Table 1). While CBp has the value of S_BET at only 88 m²·g⁻¹, CBa possesses S_BET of 644 m²·g⁻¹. V_micro in CBa makes up approx. 18% from the total pore volume, which is also nicely visible in Figure 3a. It can be summarized that the KOH activation of the pyrolytic carbon black led to further improvement of carbon black textural properties, resulting in an irregular mesoporous-macroporous structure including a larger amount of micropores.

Compared to the commercial carbon black, denoted N220 (114–124 m²·g⁻¹), N330 (78–88 m²·g⁻¹), N550 (38–46 m²·g⁻¹), and N660 (30–40 m²·g⁻¹) [27], the specific surface area of the produced CBp is similar to N330 and higher than N550 and N660. On the other hand, the specific surface of CBa is six times higher than all the mentioned types of commercial carbon black.

2.2. Sorption Experiments on Gases and Vapor

The results of sorption capacity reflect the dependence of the test material on temperature and pressure. The determination of adsorption isotherms for CBp and CBa was carried out at 20, 30, and 40 °C for pure gases (N₂ and CO₂) and pressure range 30–4000 kPa for N₂ and 30–2000 kPa for CO₂. For cyclohexane vapors, the adsorption isotherms were measured at 30 °C when the low pressures of saturated vapor were applied (10.5 kPa). The maximum gas uptake of CO₂ was registered at the lowest temperature and the highest pressure, which is in good agreement with general assumptions about adsorption processes onto solid surfaces [28], which is documented in Figure 4.

The amount of adsorbed gas at a maximum pressure of 2000 kPa (for CO₂) and 4000 kPa (for N₂) is documented in

Table 2. Results of sorption capacity in the environment of CO₂ at a pressure of 2000 kPa, comparison of experimental and literature data [16].

Adsorbed Amount of CO2	CBp	CBa	Beech NA *	Beech A *	Beech/Oak NA *	Beech/Oak A *
	/wt%
t = 20 °C	8.00	16.72	14.33	25.59	not meas.	not meas.
t = 30 °C	7.01	not meas.	13.68	24.55	not meas.	not meas.
t = 40 °C	6.71	not meas.	13.52	24.59	not meas.	not meas.

* Ref. [16], not meas.: Not measured.

and

Table 3. Results of sorption capacity in the environment of N₂ at a pressure of 4000 kPa, comparison of experimental and literature data [16].

Adsorbed Amount of N2	CBp	CBa	Beech NA *	Beech A *	Beech/Oak NA *	Beech/Oak A *
	/wt%
t = 20 °C	2.23	not meas.	5.69	7.13	4.29	4.46
t = 30 °C	1.84	not meas.	5.59	6.78	4.36	6.32
t = 40 °C	1.59	not meas.	5.67	7.37	4.46	6.62

* Ref. [16], not meas.: Not measured.

. It can be seen that the adsorbed amount of CO₂ is five times higher than the adsorbed amount of N₂ for non-activated CBp. Comparing activated and non-activated carbon blacks, the sorption capacity of CBa is two times higher than that of CBp for CO₂ at 20 °C. It can be concluded that the sorption capacity of carbon black depends on both the surface character and the porous structure of adsorbents. A generally better sorption capacity of CBp for CO₂ than for N₂ may be explained by the acid character of CO₂ and carbon black surface. The significantly improved sorption capacity of CBa for CO₂ than of CBp may be attributed to the increased surface basicity of CBa caused by the KOH activation [29]. The activation of CBp also significantly improved its porous structure, developing the microporosity as well as the meso-macroporosiy, thus enlarging the carbon black surface area which is enforced in sorption.

Table 2 and Table 3 also compare experimental and literature data. According to [16], carbon black was prepared by pyrolysis at 550 °C from beech and a mixture of beech and oak (denoted Beech NA and Beech/Oak NA). In the same temperature regime, original biomass samples were also activated with K₂CO₃ (ratio 3:1—K₂CO₃:sample) and then pyrolyzed (denoted as Beech A and Beech/Oak A).

Based on sorption experimental results, it is certain that the sorption capacity is dependent on activation and precursors of the sample. It can be seen that better sorption capacities (for CO₂ and N₂) were obtained on carbon black prepared from biomass precursors.

The sorption capacity of CBa for CO₂ is comparable to non-activated Beech NA. The best results were obtained for beech activated (Beech A), where approx. 7% of N₂ and approx. 25% of CO₂ were adsorbed. Compared to the literature [16], the sorption capacity:

• of CBp is up to three times lower than for Beech NA and Beech/Oak NA for N₂ adsorption,
• of CBp is up to two times lower than for Beech NA for CO₂ adsorption,
• of CBa is slightly higher than Beech NA for CO₂ adsorption,
• of CBa is up to two times lower than for Beech A for CO₂ adsorption.

The Langmuir isotherm [30] was used for evaluation of sorption uptake of CO₂ and cyclohexane at different temperatures on activated CBa and non-activated CBp. The linearized model of Langmuir isotherm is expressed in Equation (1), where p is vapor pressure, p₀ is saturated vapor pressure, n_A is the adsorbated amount of vapor, n_m is the monolayer capacity of the adsorbent, and K is the constant related to the energy of adsorption.

$$\frac{\mathrm{p}/{\mathrm{p}}_0}{{\mathrm{n}}_{\mathrm{A}}}=\frac{1}{{\mathrm{n}}_{\mathrm{m}}}\frac{\mathrm{p}}{{\mathrm{p}}_0}+\frac{1}{{\mathrm{Kn}}_{\mathrm{m}}{\mathrm{p}}_0}$$

(1)

The linearized Langmuir isotherm of cyclohexane on activated CBa at a temperature of 30 °C is shown in Figure 5.

The monolayer capacity of the adsorbent (n_m), the constant related to the energy of adsorption (K), and the coefficient of determination (R²) were calculated and can be seen in

Table 4. Parameters of the Langmuir isotherm with the coefficient of determination at 20 °C for N₂ and CO₂ and at 30 °C for cyclohexane.

	CBp				CBa
	nm	K	R2	S	nm	K	R2	S
	/g·g−1	/Pa−1		/m2·g−1	/g·g−1	/Pa−1		/m2·g−1
N2	0.0027	392.625	0.9466	9.3	not meas.	not meas.	not meas.	not meas.
CO2	0.0307	8.366	0.9150	79	0.1432	2.824	0.9977	367
Cyclohexane	0.0383	493.000	0.9774	118	0.1706	5.169	0.9950	526

Not meas.: Not measured.

.

Linearized data up to the relative pressure value p/p₀ of 0.2 are plotted as a solid point, data above the relative pressure value p/p₀ of 0.2 are plotted as an open point.

From the shape of Langmuir isotherms of CO₂ and cyclohexane, an increase in CO₂ gas uptake on activated CBa is visible up to p/p₀ = 0.08. On the other hand, gas uptake in cyclohexane on activated carbon CBa is most evident up to p/p₀ = 0.15. Further increasing the relative pressure leads to an increase in gas uptake of CO₂ by ~0.04 g·g⁻¹ and of cyclohexane by ~0.03 g·g⁻¹.

The monolayer capacity n_m of the adsorbent decrease in the order: CBa for cyclohexane ˃ CBa for CO₂ ˃ CBp for cyclohexane ˃ CBp for CO₂ ˃ CBp for N₂, is evident from Table 4. The adsorption of N₂ is almost negligible compared with values of CO₂ and cyclohexane. As we expected, the sorption capacity is greater for activated CBa than for non-activated carbon CBp for both gases/vapors. The coefficient of determination shows that the Langmuir isotherm model fits the data very well.

The evaluated monolayer capacity n_m of CBp and CBa was used to calculate the apparent specific surface areas of adsorbents. The cross-sectional areas of:

• N₂ was taken as 0.162 nm² [31].
• CO₂ was taken as 0.187 nm² [31].
• Cyclohexane was taken as 0.431 nm² [30].

For the adsorption of CO₂, N₂, and cyclohexane, the surface area for both CBp and CBa was calculated based on the parameters of the Langmuir isotherm. The assumption of no presence of capillary condensation was applied and determined values of surface areas were compared with those of standard nitrogen physisorption measurements, using the BET method ( Table 1 and Table 4).

Physical properties and three-dimensional spacing of adsorbate molecules are crucial parameters affecting sorption. Calculated specific areas of samples decreased in this order: cyclohexane > CO₂ > N₂. The specific surface area determined by the nitrogen S-BET method is closest to the specific surface areas obtained by CO₂ for CBp and by cyclohexane for CBa. Variations between S-BET and the specific surface from Langmuir isotherm can be explained by the different methodologies/theoretical assumptions of the applied models used for evaluation as well as by the different nature of the used adsorptive.

It is obvious from Table 1 that the activation of CBp essentially improves the textural properties (i.e., mesopore surface area, micropore volume, and total pore volume) of the final carbonaceous product (CBa), which positively affects the adsorption of gases. Activation with KOH at 800 °C leads to the active carbon samples of a well-developed porous structure with predominant micropores [1]. This feature is in agreement with the literature [32,33]. The activation of carbon black prepared by pyrolysis of waste ST with alkali, increased the sorption capacity, with a decrease in ash content. For CBa, the uptake of CO₂ is approximately three times higher and the uptake of cyclohexane is ~10 times higher than for CBp (Figure 6). The affinity of CBa to cyclohexane vapors is higher by 3% than to CO₂.

Many studies have revealed that the specific surface area of carbonaceous adsorbents is primarily responsible for physical adsorption of organic compounds. Therefore, the higher surface area of activated carbon had larger adsorption rate constants implying that physical adsorption may be the dominating mechanism [34]. The positive relationship between surface area and adsorption capacity of N₂ was investigated, which is illustrated in Figure 7. According to the literature [29,35] a larger total pore volume provides more active sites for interaction between CO₂ and the carbon black. In this article, the CO₂ adsorption capacity has a linear correlation with the micropore surface area and also BET surface area. In our case, the sorption capacity of N₂ and carbon black also shows a linear relationship. For these reasons, we could also assume a positive relationship between the sorption capacity of CO₂ and carbon black. Therefore, we connect points for sorption capacities for CO₂ with a dotted line in Figure 7. It can be concluded that the adsorption of N₂ depends only on the size of the specific surface area. Adsorption is not affected by the nature (ST or biomass) of the carbon. On the other hand, adsorption of CO₂ depends on the value of the specific surface area and also on the nature of the carbon. For lower S_BET values (<240 m²/g), the sorption capacity is higher for CBa derived from ST, conversely for higher S_BET values (>240 m²/g), the sorption capacity is higher for the activated carbon prepared from biomass [16].

3. Experimental Part

3.1. Material Preparation

Waste scrap tyres (denoted as STs) (undefined mixture, Moravia-Silesian region, Czech Republic) were collected from passenger cars from car wrecker. STs were cut into smaller pieces and steel wires were removed by hand. After that, STs were crushed with a Testchem LMN-100 mill into a smaller part and then sampled through assay sieves under 1 mm. The sieves are made by Preciselekt and comply with the ISO 3310 standard.

Pyrolytic carbon black (denoted as CBp) was prepared using thermogravimeter TG-DTA NETZSCH STA 409 EP (NETZSCH, Selb, Germany). Experiments were conducted in big 5 mL crucibles from aluminum oxide in a dynamic inert argon atmosphere (flow rate of 100 cm³·min⁻¹) at 600 °C for 3 min with a heating rate of 10 °C min⁻¹.

Ten grams of prepared CBp were mixed in the polyethylene bottle with a KOH (Merck, Kenilworth, NJ, USA) solution (121 g/100 mL) at a 1:3 mass ratio (sample:KOH). This mixture, with a small amount of tenside (commercial dish detergent, added in order to increase the wettability of CBp by KOH) was left at 25 °C for 1 day. The sample impregnated with KOH was loaded to a porcelain combustion boat. Activation took place in a quartz tube with a 25 mm inner diameter in a dynamic inert N₂ atmosphere (flow rate 200 mL min⁻¹). Activation was performed at 800 °C for 30 min in a tube furnace LT 50/300/13 (LAC, Židlochovice, Czech Republic). After activation and cooling, the sample was washed on a glass fiber filter with distilled water to achieve a neutral pH. The washed activated carbon was dried at 105 °C over night. The activated sample was denoted as CBa.

3.2. Material Characterization

Raman spectra excited in the visible range with an HeNe 633 nm laser were measured on powder samples. A microscope with an objective 50× magnification was used to focus the laser beam on the sample. The scattered light was analyzed by a spectrograph with a holographic grating of 1800 lines mm^–1. A Peltier cooled CCD detector (576 × 384 pixels) registered the dispersed light.

Nitrogen and krypton physisorption measurements at 77 K were performed by using the ASAP2020 physisorption instrument (Micromeritics, Nocross, GA, USA) and NOVA2000e (Quanta chrome Instruments, Boynton Beach, FL, USA). Prior to the physisorption measurements, the materials were degassed at 105 °C under a vacuum less than 1 Torr (133 Pa) for 14 h. The following textural properties were evaluated: Specific surface area, S_BET, from the adsorption isotherm of nitrogen or krypton for the p/p₀ = 0.05–0.25 range using the standard Brunauer-Emmett-Teller (BET) procedure [36], and mesopore surface area, S_meso, and micropore volume, V_micro, evaluated by the t-plot method [37]. Pore-size distribution (pore radius 10⁰–10² nm) was determined from the adsorption branch of nitrogen adsorption-desorption isotherm by the advanced Barrett-Joyner-Halenda (BJH) method [38,39]. The Lecloux-Pirard standard isotherm [40,41] was used for the t-plot, as well as for the pore-size distribution evaluations. The total pore volume, V_total, was determined as the adsorbed volume of nitrogen at relative pressure p/p₀ = 0.990.

The proximate analysis according to the standard ASTM D7582 (LECO, TGA 701) was done for raw scrap tyres.

The tempered experimental cell where the solid sorbent takes place, high-sensitivity balance, pressure transducer, special container for VOC in a liquid state, vacuum accessories, and a set of automatic valves are the essential parts of the thermogravimeter TGA-HP50 was employed at the sorption experiments. The operating principle and connections of the parts are illustrated in Figure 8. Inside the tempered cell there is a solid sample placed into the glass pan, which is connected to the high-sensitivity of 0.5 μg balance by a thin fiber. The sample quantity was about 35 mg. Firstly, the cell is evacuated down to the pressure below 0.1 torr. After evacuation, the drying period of the experiment starts. The sample is heated up to 120 °C and kept at such temperature for a certain time. Then, the sample is cooled down to the experimental temperature (20, 30, or 40 °C) and the low pressure (below 0.1 torr).

The adsorption part of the experiments starts when the automatic valve separating the measuring cell and valve for the gas (N₂ or CO₂) or container with a liquid VOC (cyclohexane) becomes open. The adsorption branch of the experiment consists of several constant pressure steps, which are organized with upward trends to the maximum pressure (0.03–2 MPa for CO₂; 0.03–4.5 MPa for N₂, and to the saturated pressure of cyclohexane). The mass of the adsorbent sample is measured permanently during all experimental periods. The uncertainty of measurements is when the mass of the sample is stable for 5 min ± 0.5 mass%. When the last specified pressure step at a certain temperature is complied, the experiment is finished and the pressure inside the measuring cell is gently increased to the ambient pressure.

The measured quantities were change of mass of the solid sample (g), time (min), temperature (°C), and pressure (kPa) inside the measuring cell. The model of Langmuir isotherm was used for the determination of adsorption curves of CO₂ and cyclohexane vapor.

4. Conclusions

This paper deals with the preparation and chemical activation of carbon black prepared by pyrolysis of waste scrap tyres. Non-activated pyrolytic carbon black, CBp, was prepared by pyrolysis of waste scrap tyres at the temperature of 600 °C and heating rate of 10 °C·min⁻¹ for 3 min in an inert argon. In addition to that, it was activated by a KOH solution at the temperature of 800 °C to reach the activated form of carbon black, CBa. The activation of pyrolytic carbon black, CBp, did not affect its rate of graphitization, but it significantly affected the porous structure of activated CBa. The specific surface area increased from 88 m²·g⁻¹ for non-activated CBp to 644 m²·g⁻¹ for activated CBa, in the activated CBa the irregular mesoporous-macroporous structure with a significant amount of micropores was formed due to activation.

The sorption capacity of non-activated CBp and activated CBa was investigated by inert gas—N₂, greenhouse gas—CO₂, and non-polar vapor-cyclohexane at different temperatures and pressures. The sorption capacity depends on the type of gas/vapor adsorbed and also on the character of the adsorbents. The adsorbed amount of CO₂ at our chosen experimental conditions was five times higher than the adsorbed amount of N₂ for CBp. The uptake of CO₂ was three times higher and for cyclohexane ten times higher for activated CBa than for non-activated CBp at 20 °C for CO₂ and at 30 °C for cyclohexane.

Experimental data were also treated by the linearized model of Langmuir isotherm, surface areas were calculated and compared with values determined from the linearized form of BET isotherm. In terms of closeness with the standard BET method, CO₂ appears to be the most suitable adsorbent for non-activated CBp (78 m²·g⁻¹) and cyclohexane for activated CBa (526 m²·g⁻¹).

From the linear relationship between the surface area and the sorption capacity it can be summarized that the N₂ adsorption depends only on the specific surface area and the nature of the carbon does not affect it.

It can be concluded that the production of activated carbon black from waste scrap tyres by pyrolysis shows two positive aspects from the view point of environmental protection. Firstly, the amount of waste landfilled ST, which represents a long-term ecological burden for the environment may be reduced, and secondly, a valuable solid product—activated carbon black with good sorption ability—is produced. In spite of the fact that non-activated CBp and activated CBa produced from ST do not surpass the carbon produced from biomass, the chemical activation of non-activated CBp from ST resulted in an improvement of the adsorption capacity of activated CBa.