Editor’s Choice Articles

Harmful algal blooms (HABs) are common disastrous ecological anomalies in coastal waters. An effective algae monitoring approach is important for natural disaster warning and environmental governance. However, conducting rapid and sensitive detection of multiple algae is still challenging. Here, we designed an ultrasensitive, rapid and portable double-layer microfluidic biochip for the simultaneous quantitative detection of six species of algae. Specific DNA probes based on the 18S ribosomal DNA (18S rDNA) gene fragments of HABs were designed and labeled with the fluorescent molecule cyanine-3 (Cy3). The biochip had multiple graphene oxide (GO) nanosheets-based reaction units, in which GO nanosheets were applied to transfer target DNA to the fluorescence signal through a photoluminescence detection system. The entire detection process of multiple algae was completed within 45 min with the linear range of fluorescence recovery of 0.1 fM–100 nM, and the detection limit reached 108 aM. The proposed approach has a simple detection process and high detection performance and is feasible to conduct accurate detection with matched portable detection equipment. It will have promising applications in marine natural disaster monitoring and environmental care. Full article

Control of light absorption and transmission by metal–insulator–metal (MIM) metasurfaces are promising for applications in optical windows. This study shows the realization of photo-thermal energy conversion for radiative cooling by MIM metasurfaces with thin metal substrate and Indium–Tin–Oxide (ITO). High transparency of ITO at visible wavelengths and high absorption at mid-infrared wavelengths were realized for future applications of efficient cooling or heating applicable for living and working spaces. The MIM (ITO/CaF₂/ITO) metasurface was patterned with low-resolution photo-lithography as a demonstration of further simplification and possible scalability of the patterning for practical window applications. Full article

A novel inhibitable and firing threshold voltage tunable vertical nanowire (NW) single transistor neuron device with core–shell dual-gate (CSDG) was realized and verified by TCAD simulation. The CSDG NW neuron is enclosed by an independently accessed shell gate and core gate to serve an excitatory–inhibitory transition and a firing threshold voltage adjustment, respectively. By utilizing the shell gate, the firing of specific neuron can be inhibited for winner-takes-all learning. It was confirmed that the independently accessed core gate can be used for adjustment of the firing threshold voltage to compensate random conductance variation before the learning and to fix inference error caused by unwanted synapse conductance change after the learning. This threshold voltage tuning can also be utilized for homeostatic function during the learning process. Furthermore, a myelination function which controls the transmission rate was obtained based on the inherent asymmetry between the source and drain in vertical NW structure. Finally, using the CSDG NW neuron device, a letter recognition test was conducted by SPICE simulation for a system-level validation. This multi-functional neuron device can contribute to construct a high-density monolithic SNN hardware combining with the previously developed vertical synapse MOSFET devices. Full article

The addition of fillers has been implemented in fused filament fabrication (FFF), and robust carbon fillers have been found to improve the mechanical, electrical, and thermal properties of 3D-printed matrices. However, in stretchable matrices, the use of fillers imposes significant challenges related to quality and durability. In this work, we show that long carbon staple fibers in the form of permeable carbon fiber cloth (CFC) can be placed into a stretchable thermoplastic polyurethane (TPU) matrix to improve the system. Four CFC sample series (nominally 53–159-µm-thick CFC layers) were prepared with a permeable and compliant thin CFC layer and a highly conductive and stiff thick CFC layer. The sample series was tested with single pull-up tests and cyclic tensile tests with 10,000 cycles and was further studied with digital image correlation (DIC) analyses. The results showed that embedded CFC layers in a TPU matrix can be used for stretchable 3D-printed electronics structures. Samples with a thin 53 µm CFC layer retained electrical properties at 50% cyclic tensile deformations, whereas the samples with a thick >150-µm CFC layer exhibited the lowest resistance (5 Ω/10 mm). Between those structures, the 106-µm-thick CFC layer exhibited balanced electromechanical properties, with resistance changes of 0.5% in the cyclic tests after the orientation of the samples. Furthermore, the suitability of the structure as a sensor was estimated. Full article

Micromachined thermal flow sensors on the market are primarily manufactured with the calorimetric sensing principle. The success has been in limited industries such as automotive, medical, and gas process control. Applications in some emerging and abrupt applications are hindered due to technical challenges. This paper reviews the current progress with micromachined devices based on the less popular thermal time-of-flight sensing technology: its theory, design of the micromachining process, control schemes, and applications. Thermal time-of-flight sensing could effectively solve some key technical hurdles that the calorimetric sensing approach has. It also offers fluidic property-independent data acquisition, multiparameter measurement, and the possibility for self-calibration. This technology may have a significant perspective on future development. Full article

A dual-band metasurface array is presented in this paper for electromagnetic (EM) energy harvesting in the Wi-Fi band and Ku band. The array consists of metasurface unit cells, rectifiers, and load resistors. The metasurface units within each column are interconnected to establish two channels of energy delivery, enabling the transmission and aggregation of incident power. At the terminals of two channels, a single series diode rectifier and a voltage doubler rectifier are integrated into them to rectify the energy in the Wi-Fi band and the Ku band, respectively. A 7 × 7 prototype of the metasurface array is fabricated and tested. The measured results in the anechoic chamber show that the RF-to-dc efficiencies of the prototype at 2.4 GHz and 12.6 GHz reach 64% and 55% accordingly, when the available incident power at the surface is 3 dBm and 14 dBm, respectively. Full article

With the rapid growth of emerging point-of-use (POU)/point-of-care (POC) detection technologies, miniaturized sensors for the real-time detection of gases and airborne pathogens have become essential to fight pollution, emerging contaminants, and pandemics. However, the low-cost development of miniaturized gas sensors without compromising selectivity, sensitivity, and response time remains challenging. Microfluidics is a promising technology that has been exploited for decades to overcome such limitations, making it an excellent candidate for POU/POC. However, microfluidic-based gas sensors remain a nascent field. In this review, the evolution of microfluidic gas sensors from basic electronic techniques to more advanced optical techniques such as surface-enhanced Raman spectroscopy to detect analytes is documented in detail. This paper focuses on the various detection methodologies used in microfluidic-based devices for detecting gases and airborne pathogens. Non-continuous microfluidic devices such as bubble/droplet-based microfluidics technology that have been employed to detect gases and airborne pathogens are also discussed. The selectivity, sensitivity, advantages/disadvantages vis-a-vis response time, and fabrication costs for all the microfluidic sensors are tabulated. The microfluidic sensors are grouped based on the target moiety, such as air pollutants such as carbon monoxide and nitrogen oxides, and airborne pathogens such as E. coli and SARS-CoV-2. The possible application scenarios for the various microfluidic devices are critically examined. Full article

Achieving high efficiency and throughput in droplet-based mixing over a small characteristic length, such as microfluidic channels, is one of the crucial parameters in Lab-on-a-Chip (LOC) applications. One solution to achieve efficient mixing is to use active mixers in which an external power source is utilized to mix two fluids. One of these active methods is magnetic micromixers using ferrofluid. In this technique, magnetic nanoparticles are used to make one phase responsive to magnetic force, and then by applying a magnetic field, two fluid phases, one of which is magneto-responsive, will sufficiently mix. In this study, we investigated the effect of the magnetic field’s characteristics on the efficiency of the mixing process inside droplets. When different concentrations of ferrofluids are affected by a constant magnetic field, there is no significant change in mixing efficiency. As the magnetic field intensifies, the magnetic force makes the circulation flow inside the droplet asymmetric, leading to chaotic advection, which creates a flow that increases the mixing efficiency. The results show that the use of magnetic fields is an effective method to enhance the mixing efficiency within droplets, and the efficiency of mixing increases from 65.4 to 86.1% by increasing the magnetic field intensity from 0 to 90 mT. Besides that, the effect of ferrofluid’s concentration on the mixing efficiency is studied. It is shown that when the concentration of the ferrofluid changes from 0 to 0.6 mol/m³, the mixing efficiency increases considerably. It is also shown that by changing the intensity of the magnetic field, the mixing efficiency increases by about 11%. Full article

Terahertz (THz) technology offers unparalleled opportunities in a wide variety of applications, ranging from imaging and spectroscopy to communications and quality control, where lack of efficient modulation devices poses a major bottleneck. Spatial modulation allows for dynamically encoding various spatial information into the THz wavefront by electrical or optical control. It plays a key role in single-pixel imaging, beam scanning and wavefront shaping. Although mature techniques from the microwave and optical band are not readily applicable when scaled to the THz band, the rise of metasurfaces and the advance of new materials do inspire new possibilities. In this review, we summarize the recent progress of THz spatial light modulators from the perspective of functional materials and analyze their modulation principles, specifications, applications and possible challenges. We envision new advances of this technique in the near future to promote THz applications in different fields. Full article

To improve suitability in applications with high dynamic performance requirements, the transient response characteristics of high-power piezoelectric transducers should be studied quantitatively. This paper proposes the vector reduction method to solve the complex transient equations and obtains a transient matching scheme clarifying the mechanism of electrical matching resistance on electromechanical damping. A matching scheme with a combination of full-bridge inverter, transformer and series LC circuit is designed and validated, which can provide suitable electrical damping without causing energy losses. Consequently, the experiment verifies the transient properties of the proposed scheme. For a typical piezoelectric cutting transducer with 100.8 ms response time, our scheme is verified to have high dynamic performance within frequency response time of 5.5 ms and vibration response time of 15.0 ms. Full article

Although nanomedicine has been highly investigated for cancer treatment over the past decades, only a few nanomedicines are currently approved and in the market; making this field poorly represented in clinical applications. Key research gaps that require optimization to successfully translate the use of nanomedicines have been identified, but not addressed; among these, the lack of control of the release pattern of therapeutics is the most important. To solve these issues with currently used nanomedicines (e.g., burst release, systemic release), different strategies for the design and manufacturing of nanomedicines allowing for better control over the therapeutic release, are currently being investigated. The inclusion of stimuli-responsive properties and prolonged drug release have been identified as effective approaches to include in nanomedicine, and are discussed in this paper. Recently, smart sustained release nanoparticles have been successfully designed to safely and efficiently deliver therapeutics with different kinetic profiles, making them promising for many drug delivery applications and in specific for cancer treatment. In this review, the state-of-the-art of smart sustained release nanoparticles is discussed, focusing on the design strategies and performances of polymeric nanotechnologies. A complete list of nanomedicines currently tested in clinical trials and approved nanomedicines for cancer treatment is presented, critically discussing advantages and limitations with respect to the newly developed nanotechnologies and manufacturing methods. By the presented discussion and the highlight of nanomedicine design criteria and current limitations, this review paper could be of high interest to identify key features for the design of release-controlled nanomedicine for cancer treatment. Full article

This work proposes a miniaturized piezoelectric MEMS accelerometer based on polygonal topology with an area of only 868 × 833 μm². The device consists of six trapezoidal cantilever beams with shorter fixed sides. Meanwhile, a device with larger fixed sides is also designed for comparison. The theoretical and finite element models are established to analyze the effect of the beam′s effective stiffness on the output voltage and natural frequency. As the stiffness of the device decreases, the natural frequency of the device decreases while the output signal increases. The proposed polygonal topology with shorter fixed sides has higher voltage sensitivity than the larger fixed one based on finite element simulations. The piezoelectric accelerometers are fabricated using Cavity-SOI substrates with a core piezoelectric film of aluminum nitride (AlN) of about 928 nm. The fabricated piezoelectric MEMS accelerometers have good linearity (0.99996) at accelerations less than 2 g. The measured natural frequency of the accelerometer with shorter fixed sides is 98 kHz, and the sensitivity, resolution, and minimum detectable signal at 400 Hz are 1.553 mV/g, 1 mg, and 2 mg, respectively. Compared with the traditional trapezoidal cantilever with the same diaphragm area, its output voltage sensitivity is increased by 22.48%. Full article

In the new age of illumination, light emitting diodes (LEDs) have been proven to be the most efficient alternative to conventional light sources. Yet, in comparison to other lighting systems, LEDs operate at low temperatures while junction temperature (T_j) is is among the main factors dictating their lifespan, reliability, and performance. This indicates that accurate measurement of LED temperature is of great importance to better understand the thermal effects over a system and improve performance. Over the years, various T_j measurement techniques have been developed, and existing methods have been improved in many ways with technological and scientific advancements. Correspondingly, in order to address the governing phenomena, benefits, drawbacks, possibilities, and applications, a wide range of measurement techniques and systems are covered. This paper comprises a large number of published studies on junction temperature measurement approaches for LEDs, and a summary of the experimental parameters employed in the literature are given as a reference. In addition, some of the corrections noted in non-ideal thermal calibration processes are discussed and presented. Finally, a comparison between methods will provide the readers a better insight into the topic and direction for future research. Full article

Electromagnetic bi-directional micropumps (EMBM) are indispensable for the development of portable devices which enable fluid transportation in forward and reverse directions. However, the high disposal cost of rare-earth magnets attached to the fluidic part and the low pump density due to multiple motors limit their practical application in disposable multi-channel microfluidic applications such as droplet-based oscillatory-flow (DBOF) rapid PCR amplification. Therefore, this paper presented a low-cost, disposable, high-pump-density EMBM. To reduce the disposal cost, we separated the magnets from the disposable fluidic part and used cylindrical holes to store and guide the magnet, which resulted in the ability to reuse all the magnets. To increase the pump density, we used the combination of one motor and one multi-pole ring magnet to drive several channels simultaneously. A proof-of-concept prototype with a pump density of 0.28 cm⁻² was fabricated and experimentally evaluated. The fabricated micropump exhibited a maximum flow rate of 0.86 mL/min and a maximum backpressure of 0.5 kPa at a resonant frequency around 50 Hz. The developed multi-channel micropump with reusable magnets is highly beneficial to the development of low-cost and high-throughput rapid PCR amplification microchips and therefore can have a significant impact on timely infectious disease recognition and intervention. Full article

The global RE100 campaign is attracting attention worldwide due to climate change caused by global warming, increasingly highlighting the efficiency of renewable energy. Texturing of photovoltaic devices increases the devices’ efficiency by reducing light reflectance at their surfaces. This study introduces the change in light reflectance following the process conditions of plasma etching as a texturing process to increase the efficiency of photovoltaic cells. Isotropic etching was induced through plasma using SF₆ gas, and the etch profile was modulated by adding O₂ gas to reduce light reflectance. A high etch rate produces high surface roughness, which results in low surface reflectance properties. The inverse moth-eye structure was implemented using a square PR pattern arranged diagonally and showed the minimum reflectance in visible light at a tip spacing of 1 μm. This study can be applied to the development of higher-efficiency optical devices. Full article

To maximize the performance of energy storage systems more effectively, modern batteries/supercapacitors not only require high energy density but also need to be fully recharged within a short time or capable of high-power discharge for electric vehicles and power applications. Thus, how to improve the rate capability of batteries or supercapacitors is a very important direction of research and engineering. Making low-tortuous structures is an efficient means to boost power density without replacing materials or sacrificing energy density. In recent years, numerous manufacturing methods have been developed to prepare low-tortuous configurations for fast ion transportation, leading to impressive high-rate electrochemical performance. This review paper summarizes several smart manufacturing processes for making well-aligned 3D microstructures for batteries and supercapacitors. These techniques can also be adopted in other advanced fields that require sophisticated structural control to achieve superior properties. Full article

We report on the fabrication and electrical characterization of AlGaN/GaN normally off transistors on silicon designed for high-voltage operation. The normally off configuration was achieved with a p-gallium nitride (p-GaN) cap layer below the gate, enabling a positive threshold voltage higher than +1 V. The buffer structure was based on AlN/GaN superlattices (SLs), delivering a vertical breakdown voltage close to 1.5 kV with a low leakage current all the way to 1200 V. With the grounded substrate, the hard breakdown voltage transistors at V_GS = 0 V is 1.45 kV, corresponding to an outstanding average vertical breakdown field higher than 2.4 MV/cm. High-voltage characterizations revealed a state-of-the-art combination of breakdown voltage at V_GS = 0 V together with low buffer electron trapping effects up to 1.4 kV, as assessed by means of substrate ramp measurements. Full article

Cryopreservation is the final step of stem cell production before the cryostorage of the product. Conventional methods of adding cryoprotecting agents (CPA) into the cells can be manual or automated with robotic arms. However, challenging issues with these methods at industrial-scale production are the insufficient mixing of cells and CPA, leading to damage of cells, discontinuous feeding, the batch-to-batch difference in products, and, occasionally, cross-contamination. Therefore, the current study proposes an alternative way to overcome the abovementioned challenges; a highly efficient micromixer for low-cost, continuous, labour-free, and automated mixing of stem cells with CPA solutions. Our results show that our micromixer provides a more homogenous mixing of cells and CPA compared to the manual mixing method, while the cell properties, including surface markers, differentiation potential, proliferation, morphology, and therapeutic potential, are well preserved. Full article

Breast cancer is the most common type of cancer and it is treated with surgical intervention, radiotherapy, chemotherapy, or a combination of these regimens. Despite chemotherapy’s ample use, it has limitations such as bioavailability, adverse side effects, high-dose requirements, low therapeutic indices, multiple drug resistance development, and non-specific targeting. Drug delivery vehicles or carriers, of which nanocarriers are prominent, have been introduced to overcome chemotherapy limitations. Nanocarriers have been preferentially used in breast cancer chemotherapy because of their role in protecting therapeutic agents from degradation, enabling efficient drug concentration in target cells or tissues, overcoming drug resistance, and their relatively small size. However, nanocarriers are affected by physiological barriers, bioavailability of transported drugs, and other factors. To resolve these issues, the use of external stimuli has been introduced, such as ultrasound, infrared light, thermal stimulation, microwaves, and X-rays. Recently, ultrasound-responsive nanocarriers have become popular because they are cost-effective, non-invasive, specific, tissue-penetrating, and deliver high drug concentrations to their target. In this paper, we review recent developments in ultrasound-guided nanocarriers for breast cancer chemotherapy, discuss the relevant challenges, and provide insights into future directions. Full article

Mobile millimeter and centimeter scale robots often use smart composite manufacturing (SCM) for the construction of body components and mechanisms. The fabrication of SCM mechanisms requires laser machining and laminating flexible, adhesive, and structural materials into small-scale hinges, transmissions, and, ultimately, wings or legs. However, a fundamental limitation of SCM components is the plastic deformation and failure of flexures. In this work, we demonstrate that encasing SCM components in a soft silicone mold dramatically improves the durability of SCM flexure hinges and provides robustness to SCM components. We demonstrate this advance in the design of a flapping-wing robot that uses an underactuated compliant transmission fabricated with an inner SCM skeleton and exterior silicone mold. The transmission design is optimized to achieve desired wingstroke requirements and to allow for independent motion of each wing. We validate these design choices in bench-top tests, measuring transmission compliance, kinematics, and fatigue. We integrate the transmission with laminate wings and two types of actuation, demonstrating elastic energy exchange and limited lift-off capabilities. Lastly, we tested collision mitigation through flapping-wing experiments that obstructed the motion of a wing. These experiments demonstrate that an underactuated compliant transmission can provide resilience and robustness to flapping-wing robots. Full article

Nanocrystalline diamond capping layers have been demonstrated to improve thermal management for AlGaN/GaN HEMTs. To improve the RF devices, the application of the technology, the technological approaches and device characteristics of AlGaN/GaN HEMTs with gate length less than 0.5 μm using nanocrystalline diamond capping layers have been studied systematically. The approach of diamond-before-gate has been adopted to resolve the growth of nanocrystalline diamond capping layers and compatibility with the Schottky gate of GaN HEMTs, and the processes of diamond multi-step etching technique and AlGaN barrier protection are presented to improve the technological challenge of gate metal. The GaN HEMTs with nanocrystalline diamond passivated structure have been successfully prepared; the heat dissipation capability and electrical characteristics have been evaluated. The results show the that thermal resistance of GaN HEMTs with nanocrystalline diamond passivated structure is lower than conventional SiN-GaN HEMTs by 21.4%, and the mechanism of heat transfer for NDC-GaN HEMTs is revealed by simulation method in theory. Meanwhile, the GaN HEMTs with nanocrystalline diamond passivated structure has excellent output, small signal gain and cut-off frequency characteristics, especially the current–voltage, which has a 27.9% improvement than conventional SiN-GaN HEMTs. The nanocrystalline diamond capping layers for GaN HEMTs has significant performance advantages over the conventional SiN passivated structure. Full article

Nanoparticles are widely used in the pharmaceutical industry due to their high surface-to-volume ratio. Among the many techniques used to obtain nanoparticles, those based on supercritical fluids ensure reduced dimensions, narrow particle size distributions, and a very low or zero solvent residue in the powders. This review focuses on using supercritical carbon dioxide-based processes to obtain the nanoparticles of compounds used for the treatment or prevention of cancer. The scientific literature papers have been classified into two groups: nanoparticles consisting of a single active principle ingredient (API) and carrier/API nanopowders. Various supercritical carbon dioxide (scCO₂) based techniques for obtaining the nanoparticles were considered, along with the operating conditions and advantages and disadvantages of each process. Full article

In a lidar system, replacing moving components with solid-state devices is highly anticipated to make a reliable and compact lidar system, provided that a substantially large beam area with a large angular extent as well as high angular resolution is assured for the lidar transmitter and receiver. A new quasi-solid-state lidar optical architecture employs a transmitter with a two-dimensional MEMS mirror for fine beam steering at a fraction of the degree of the angular resolution and is combined with a digital micromirror device for wide FOV scanning over 37 degree while sustaining a large aperture area of 140 mm squared. In the receiver, a second digital micromirror device is synchronized to the transmitter DMD, which enables a large FOV receiver. An angular resolution of $0.57°\left(H\right)$by $0.23°\left(V\right)$ was achieved with 0.588 fps for scanning 1344 points within the field of view. Full article

Non-invasive continuous blood pressure monitoring is of great significance for the preventing, diagnosing, and treating of cardiovascular diseases (CVDs). Studies have demonstrated that photoplethysmogram (PPG) and electrocardiogram (ECG) signals can effectively and continuously predict blood pressure (BP). However, most of the BP estimation models focus on the waveform features of the PPG signal, while the peak value of R-wave in ECG is only used as a time reference, and few references investigated the ECG waveforms. This paper aims to evaluate the influence of three characteristic waveforms in ECG on the improvement of BP estimation. PPG is the primary signal, and five input combinations are formed by adding ECG, P wave, QRS complex, T wave, and none. We employ five common convolutional neural networks (CNN) to validate the consistency of the contribution. Meanwhile, with the visualization of Gradient-weighted class activation mapping (Grad-CAM), we generate the heat maps and further visualize the distribution of CNN’s attention to each waveform of PPG and ECG. The heat maps show that networks pay more attention to the QRS complex and T wave. In the comparison results, the QRS complex and T wave have more contribution to minimizing errors than P wave. By separately adding P wave, QRS complex, and T wave, the average MAE of these networks reaches 7.87 mmHg, 6.57 mmHg, and 6.21 mmHg for systolic blood pressure (SBP), and 4.27 mmHg, 3.65 mmHg, and 3.73 mmHg, respectively, for diastolic blood pressure (DBP). The results of the experiment show that QRS complex and T wave deserves more attention and feature extraction like PPG waveform features in the continuous BP estimation. Full article

Nucleic acid detection is widely used in disease diagnosis, food safety, environmental monitoring and many other research fields. The continuous development of rapid and sensitive new methods to detective nucleic acid is very important for practical application. In this study, we developed a rapid nucleic-acid detection method using polymerase chain reaction (PCR) combined with electrokinetic preconcentration based on ion concentration polarization (ICP). Using a Nafion film, the proposed ICP microfluidic chip is utilized to enrich the nucleic acid molecules amplified by PCR thermal cycles. To demonstrate the capability of the microfluidic device and the hybrid nucleic-acid detection method, we present an animal-derived component detection experiment for meat product identification applications. With the reduced cycle numbers of 24 cycles, the detection can be completed in about 35 min. The experimental results show that this work can provide a microfluidic device and straightforward method for rapid detection of nucleic acids with reduced cycle numbers. Full article

Kidney diseases often lack optimal treatments, causing millions of deaths each year. Thus, developing appropriate model systems to study human kidney disease is of utmost importance. Some of the most promising human kidney models are organoids or small organ-resembling tissue collectives, derived from human-induced pluripotent stem cells (hiPSCs). However, they are more akin to a first-trimester fetal kidney than an adult kidney. Therefore, new strategies are needed to advance their maturity. They have great potential for disease modeling and eventually auxiliary therapy if they can reach the maturity of an adult kidney. In this review, we will discuss the current state of kidney organoids in terms of their similarity to the human kidney and use as a disease modeling system thus far. We will then discuss potential pathways to advance the maturity of kidney organoids to match an adult kidney for more accurate human disease modeling. Full article

Microarrays are essential components of analytical instruments. The elements of microarrays may be imbued with additional functionalities and encodings using composite materials and structures, but traditional microfabrication methods present substantial barriers to fabrication, design, and scalability. In this work, a tool-free technique was reported to additively batch-construct micromolded, composite, and arrayed microstructures. The method required only a compatible carrier fluid to deposit a material onto a substrate with some topography. Permutations of this basic fabrication approach were leveraged to gain control over the volumes and positions of deposited materials within the microstructures. As a proof of concept, cell micro-carrier arrays were constructed to demonstrate a range of designs, compositions, functionalities, and applications for composite microstructures. This approach is envisioned to enable the fabrication of complex composite biological and synthetic microelements for biosensing, cellular analysis, and biochemical screening. Full article

Radial artery pulse pressure contains abundant cardiovascular physiological and pathological information, which plays an important role in clinical diagnosis of traditional Chinese medical science. However, many photoelectric sensors and pressure sensors will lose a large number of waveform features in monitoring pulse, which will make it difficult for doctors to precisely evaluate the patients’ health. In this letter, we proposed an on-skin flexible pressure sensor for monitoring radial artery pulse. The sensor consists of the MXene (Ti₃C₂T_x)-coated nonwoven fabrics (n-WFs) sensitive layer and laser-engraved interdigital copper electrodes. Benefiting from substantially increased conductive paths between fibers and electrodes during normal compression, the sensor obtains high sensitivity (3.187 kPa⁻¹), fast response time (15 ms), low detection limit (11.1 Pa), and long-term durability (20,000 cycles). Furthermore, a flexible processing circuit was connected with the sensor mounted on wrist radial artery, achieving wirelessly precise monitoring of the pulse on smart phones in real time. Compared with the commercial flexible pressure sensor, our sensor successfully captures weak systolic peak precisely, showing its great clinical potential and commercial value. Full article

This study aimed to improve and investigate the oscillation dynamics and levitation stability of acoustically levitated water droplets. Contactless sample manipulation technology in mid-air has attracted significant attention in the fields of biochemistry and pharmaceutical science. Although one promising method is acoustic levitation, most studies have focused on a single sample. Therefore, it is important to determine the stability of multiple samples during acoustic levitation. Here, we aim to understand the effect of multiple-sample levitation on levitation stability in acoustic fields. We visualized the oscillatory motion of multiple levitated droplets using a high-speed video camera. To characterize the dynamics of multiple levitating droplets, the oscillation frequency and restoring force coefficients of the levitated samples, which were obtained from the experimental data, were analyzed to quantify the droplet–droplet interaction. The oscillation model of the spring-mass system was compared with the experimental results, and we found that the number of levitating droplets and their position played an important role in the levitation stability of the droplets. Our insights could help us understand the oscillatory behavior of levitated droplets to achieve more stable levitation. Full article

Spatter is an inherent, unpreventable, and undesired phenomenon in laser powder bed fusion (L-PBF) additive manufacturing. Spatter behavior has an intrinsic correlation with the forming quality in L-PBF because it leads to metallurgical defects and the degradation of mechanical properties. This impact becomes more severe in the fabrication of large-sized parts during the multi-laser L-PBF process. Therefore, investigations of spatter generation and countermeasures have become more urgent. Although much research has provided insights into the melt pool, microstructure, and mechanical property, reviews of spatter in L-PBF are still limited. This work reviews the literature on the in situ detection, generation, effects, and countermeasures of spatter in L-PBF. It is expected to pave the way towards a novel generation of highly efficient and intelligent L-PBF systems. Full article

Various conditions cause dispersions of particulate matter to circulate inside the anterior chamber of a human eye. These dispersed particles might reduce visual acuity or promote elevation of intraocular pressure (IOP), causing secondary complications such as particle related glaucoma, which is a major cause of blindness. Medical and surgical treatment options are available to manage these complications, yet preventive measures are not currently available. Conceptually, manipulating these dispersed particles in a way that reduces their negative impact could prevent these complications. However, as the eye is a closed system, manipulating dispersed particles in it is challenging. Standing acoustic waves have been previously shown to be a versatile tool for manipulation of bioparticles from nano-sized extracellular vesicles up to millimeter-sized organisms. Here we introduce for the first time a novel method utilizing standing acoustic waves to noninvasively manipulate intraocular particles inside the anterior chamber. Using a cylindrical acoustic resonator, we show ex vivo manipulation of pigmentary particles inside porcine eyes. We study the effect of wave intensity over time and rule out temperature changes that could damage tissues. Optical coherence tomography and histologic evaluations show no signs of damage or any other side effect that could be attributed to acoustic manipulation. Finally, we lay out a clear pathway to how this technique can be used as a non-invasive tool for preventing secondary glaucoma. This concept has the potential to control and arrange intraocular particles in specific locations without causing any damage to ocular tissue and allow aqueous humor normal outflow which is crucial for maintaining proper IOP levels. Full article

In this paper, a MEMS (Micro Electro Mechanical Systems)-based frequency-tunable metamaterial absorber for millimeter-wave application was demonstrated. To achieve the resonant-frequency tunability of the absorber, the unit cell of the proposed metamaterial was designed to be a symmetric split-ring resonator with a stress-induced MEMS cantilever array having initial out-of-plane deflections, and the cantilevers were electrostatically actuated to generate a capacitance change. The dimensional parameters of the absorber were determined via impedance matching using a full electromagnetic simulation. The designed absorber was fabricated on a glass wafer with surface micromachining processes using a photoresist sacrificial layer and the oxygen-plasma-ashing process to release the cantilevers. The performance of the fabricated absorber was experimentally validated using a waveguide measurement setup. The absorption frequency shifted down according to the applied DC (direct current) bias voltage from 28 GHz in the initial off state to 25.5 GHz in the pull-down state with the applied voltage of 15 V. The measured reflection coefficients at those frequencies were −5.68 dB and −33.60 dB, corresponding to the peak absorptivity rates of 72.9 and 99.9%, respectively. Full article

Micro-actuators driven on resonance maximize reach and speed; however, due to their sensitivity to environmental factors (e.g., temperature and air pressure), the amplitude and phase response must be monitored to achieve an accurate actuator position. We introduce an MEMS (microelectromechanical system) amplitude and phase monitor (MAPM) with a signal-to-noise ratio of 51 dB and 11.0 kHz bandwidth, capable of simultaneously driving and sensing the movement of 1D and 2D electrostatically driven micro-actuators without modifying the chip or its packaging. The operational principle is to electromechanically modulate the amplitude of a high-frequency signal with the changing capacitance of the micro-actuator. MAPM operation is characterized and verified by simultaneously measuring the amplitude and phase frequency response of commercial micromirrors. We demonstrate that the MAPM circuitry is insensitive to complex relationships between capacitance and position of the MEMS actuators, and it is capable of giving real-time read-out of the micromirror motion. Our measurements also reveal and quantify observations of phase drift and crosstalk in 2D resonant operation. Measurements of phase changes over time under normal operation also verify the need for phase monitoring. The open-loop, high-sensitivity position sensor enables detailed characterization of dynamic micro-actuator behavior, leading to new insights and new types of operation, including improved control of nonlinear motion. Full article

This report outlines a proposed method of packaging wide-angle (WA) mini-light-emitting diode (mini-LED) devices without optical lenses to create a highly efficient, ultrathin, flexible planar backlight for portable quantum dot light-emitting diode (QLED) displays. Since the luminous intensity curve for mini-LEDs generally recommends a beam angle of 120°, numerous LEDs are necessary to achieve a uniform surface light source for a QLED backlight. The light-guide layer and diffusion layer were packaged together on a chip surface to create WA mini-LEDs with a viewing angle of 180°. These chips were then combined with a quantum dot (QD) film and an optical film to create a high-efficiency, ultrathin, flexible planar light source with excellent color purity that can be used as a QLED display backlight. A 6 in (14.4 cm) light source was used as an experimental sample. When 1.44 W was supplied to the sample, the 3200-piece WA mini-LED with a flexible planar QLED display had a beam angle of 180° on the luminous intensity curve, a planar backlight thickness of 0.98 mm, a luminance of 10,322 nits, and a luminance uniformity of 92%. Full article

In microfluidic studies of improved oil recovery, mostly pore networks with uniform depth and surface chemistry are used. To better mimic the multiple porosity length scales and surface heterogeneity of carbonate reservoirs, we coated a 2.5D glass microchannel with calcite particles. After aging with formation water and crude oil (CRO), high-salinity Water (HSW) was flooded at varying temperatures and durations. Time-resolved microscopy revealed the CRO displacements. Precise quantification of residual oil presented some challenges due to calcite-induced optical heterogeneity and brine–oil coexistence at (sub)micron length scales. Both issues were addressed using pixel-wise intensity calibration. During waterflooding, most of the ultimately produced oil gets liberated within the first pore volume (similar to glass micromodels). Increasing temperature from 22 °C to 60 °C and 90 °C produced some more oil. Waterflooding initiated directly at 90 °C produced significantly more oil than at 22 °C. Continuing HSW exposure at 90 °C for 8 days does not release additional oil; although, a spectacular growth of aqueous droplets is observed. The effect of calcite particles on CRO retention is weak on flat surfaces, where the coverage is ~20%. The calcite-rich pore edges retain significantly more oil suggesting that, in our micromodel wall roughness is a stronger determinant for oil retention than surface chemistry. Full article

Electroactive polymer (EAP) is a polymer that reacts to electrical stimuli, such as voltage, and can be divided into electronic and ionic EAP by an electrical energy transfer mechanism within the polymer. The mechanism of ionic EAP is the movement of the positive ions inducing voltage change in the polymer membrane. Among the ionic EAPs, an ionic polymer–metal composite (IPMC) is composed of a metal electrode on the surface of the polymer membrane. A common material for the polymer membrane of IPMC is Nafion containing hydrogen ions, and platinum, gold, and silver are commonly used for the electrode. As a result, IPMC has advantages, such as low voltage requirements, large bending displacement, and bidirectional actuation. Manufacturing of IPMC is composed of preparing the polymer membrane and plating electrode. Preparation methods for the membrane include solution casting, hot pressing, and 3D printing. Meanwhile, electrode formation methods include electroless plating, electroplating, direct assembly process, and sputtering deposition. The manufactured IPMC is widely demonstrated in applications such as grippers, micro-pumps, biomedical, biomimetics, bending sensors, flow sensors, energy harvesters, biosensors, and humidity sensors. This paper will review the overall field of IPMC by demonstrating the categorization, principle, materials, and manufacturing method of IPMC and its applications. Full article

We guide the use of organ-on-chip technology in tissue engineering applications. Organ-on-chip technology is a form of microengineered cell culture platform that elaborates the in-vivo like organ or tissue microenvironments. The organ-on-chip platform consists of microfluidic channels, cell culture chambers, and stimulus sources that emulate the in-vivo microenvironment. These platforms are typically engraved into an oxygen-permeable transparent material. Fabrication of these materials requires the use of microfabrication strategies, including soft lithography, 3D printing, and injection molding. Here we provide an overview of what is an organ-on-chip platform, where it can be used, what it is composed of, how it can be fabricated, and how it can be operated. In connection with this topic, we also introduce an overview of the recent applications, where different organs are modeled on the microscale using this technology. Full article

Miniature soft sensors are crucial for the perception of soft robots. Although centimeter-scale sensors have been well developed, very few works addressed millimeter-scale, three-dimensional-shaped soft sensors capable of measuring multi-axis forces. In this work, we developed a millimeter-scale (overall size of 6 mm × 11 mm × 11 mm) soft sensor based on liquid metal printing technology and self-folding origami parallel mechanism. The origami design of the sensor enables the soft sensor to be manufactured within the plane and then fold into a three-dimensional shape. Furthermore, the parallel mechanism allows the sensor to rotate along two orthogonal axes. We showed that the soft sensor can be self-folded (took 17 s) using a shape-memory polymer and magnets. The results also showed that the sensor prototype can reach a deformation of up to 20 mm at the tip. The sensor can realize a measurement of external loads in six directions. We also showed that the soft sensor enables underwater sensing with a minimum sensitivity of 20 mm/s water flow. This work may provide a new manufacturing method and insight into future millimeter-scale soft sensors for bio-inspired robots. Full article

This paper deals with the detection of small magnetization using a thin film magneto-impedance sensor with subjecting to strong normal field. The sensor was made by soft magnetic amorphous thin-film with uniaxial magnetic anisotropy in the width direction of the element. It was reported that the sensor has very high sensitivity, such as pico-tesla order, when it is driven by hundreds of MHz. In this paper, a sensitive measurement method aiming for detection of a small particle or a cluster of nano-particles, having low-remanence, is proposed. The point is the application of strong normal field in the measurement area including sensor element and particle. The normal strong field is applied in the normal direction of the sensor plane in the value almost hundreds of mT. Instead of such strong normal field, the sensor keeps high sensitivity, because of the demagnetizing force in the thickness direction. A theoretical estimation for clarifying an efficiency of the method, experimental results of sensor property and sensitivity with subjecting to the normal field, and also a confirmation of detection of a small particle using the proposed method is reported. As a special mention, detection fundamentals when a applied surface normal field has a distribution and also a particle would run through in the vicinity of sensor is discussed. Full article

In miniature mobile robots, reducing the number of actuators can effectively reduce the size and weight of the robot. However, it is challenging to design a robot with as few actuators as possible without losing good motion performance. This work presented a simple-structured low-cost miniature mobile robot. It is driven by only a single tilted motor and yet is fully capable of being controlled to move forward and turn left or right on the ground. Based on the stick–slip mechanism, the robot’s motion is achieved by interplaying between the centrifugal force generated by the vibration motor tilted on the robot and the friction force of the robot. The robot’s speed can be controlled by regulating the magnitude and the period of the applied voltage. Finally, the robot can translate and rotate on the ground and follow various arbitrary paths. The prototype weighs only 11.15 g, costs $6.35, and is 20 mm in diameter and 25 mm in height. The proposed system is experimentally verified and demonstrates the controllability of the robot by the movement along a straight line, a circle, and more arbitrary paths. Full article

Most current thermal MEMS use fragile structures such as thin-film membranes or microcantilevers for thermal isolation. To increase the robustness of these devices, solid thermal insulators that are compatible with MEMS cleanroom processing are needed. This work introduces a novel approach for microscale thermal isolation using porous microstructures created with the recently developed PowderMEMS wafer-level process. MEMS devices consisting of heaters on a thin-film membrane were modified with porous microstructures made from three different materials. A thermal model for the estimation of the resulting thermal conductivity was developed, and measurements for porous structures in ambient air and under vacuum were performed. The PowderMEMS process was successfully used to create microscale thermal insulators in silicon cavities at the wafer level. Measurements indicate thermal conductivities of close to 0.1 W/mK in ambient air and close to 0.04 W/mK for porous structures under vacuum for the best-performing material. The obtained thermal conductivities are lower than those reported for both glass and porous silicon, making PowderMEMS a very interesting alternative for solid microscale thermal isolation. Full article

THz band-pass filters were fabricated by femtosecond-laser ablation of 25-$\mathsf{\mu }$m-thick micro-foils of stainless steel and Kapton film, which were subsequently metal coated with a ∼70 nm film, closely matching the skin depth at the used THz spectral window. Their spectral performance was tested in transmission and reflection modes at the Australian Synchrotron’s THz beamline. A 25-$\mathsf{\mu }$m-thick Kapton film performed as a Fabry–Pérot etalon with a free spectral range ($FSR$) of 119 cm${}^{-1}$, high finesse $F_c\approx 17$, and was tuneable over ∼$10\mathsf{\mu }$m (at ∼5 THz band) with $\beta ={30}^{\circ }$ tilt. The structure of the THz beam focal region as extracted by the first mirror (slit) showed a complex dependence of polarisation, wavelength and position across the beam. This is important for polarisation-sensitive measurements (in both transmission and reflection) and requires normalisation at each orientation of linear polarisation. Full article

Slippery liquid-infused porous surfaces (SLIPSs) have become an effective method to provide materials with sliding performance and, thus, achieve liquid repellency, through the process of infusing lubricants into the microstructure of the surface. However, the construction of microstructures on high-strength metals is still a significant challenge. Herein, we used a femtosecond laser with a temporally shaped Bessel beam to process NiTi alloy, and created uniform porous structures with a microhole diameter of around 4 µm, in order to store and lock lubricant. In addition, as the lubricant is an important factor that can influence the sliding properties, five different lubricants were selected to prepare the SLIPSs, and were further compared in terms of their sliding behavior. The temperature cycle test and the hydraulic pressure test were implemented to characterize the durability of the samples, and different liquids were used to investigate the possible failure under complex fluid conditions. In general, the prepared SLIPSs exhibited superior liquid repellency. We believe that, in combination with a femtosecond laser, slippery liquid-infused porous surfaces are promising for applications in a wide range of areas. Full article

The assessment of the biodegradability of nanomaterials is of pragmatic importance for understanding the interactions between nanomaterials and biological systems and for the determination of ultimate fate of these materials as well as their potential use. We recently developed carbon-based biconcave nanodisks (CBBNs) serving as a versatile nanocarrier for enhanced accumulation in tumors and combined photothermal-chemotherapy. Here, we investigate both the enzymatic and cellular degradation of CBBNs by monitoring their cellular response with electron microscopy, near-infrared absorbance spectroscopy, and cell viability and oxidative stress assessments. Our results show that CBBNs underwent significant degradation in solutions catalyzed by horseradish peroxidase (HRP) and hydrogen peroxide (H₂O₂), or in the presence of macrophage cells. The ability of CBBNs to be degraded in biological systems provides suitability for their future biomedical applications. Full article

Programmability in femtosecond-laser-written integrated circuits is commonly achieved with the implementation of thermal phase shifters. Recent work has shown how such phase shifters display significantly reduced power dissipation and thermal crosstalk with the implementation of thermal isolation structures. However, the aforementioned phase shifter technology is based on a single gold film, which poses severe limitations on integration density and circuit complexity due to intrinsic geometrical constraints. To increase the compactness, we propose two improvements to this technology. Firstly, we fabricated thermal phase shifters with a photolithography process based on two different metal films, namely (1) chromium for microheaters and (2) copper for contact pads and interconnections. Secondly, we developed a novel curved isolation trench design that, along with a state-of-the-art curvature radius, allows for a significant reduction in the optical length of integrated circuits. As a result, curved Cr-Cu phase shifters provide a compact footprint with low parasitic series resistance and no significant increase in power dissipation (∼38 mW) and thermal crosstalk (∼20%). These results pave the way toward the fabrication of femtosecond-laser-written photonic circuits with a steep increase in terms of layout complexity. Full article

The combination of paraffin wax and O,O′-bis(2-aminopropyl) polypropylene glycol–block–polyethylene glycol–block–polypropylene glycol was used as a phase-change material (PCM) for the controlled delivery of curcumin. The PCM was combined with a graphene-based heater derived from the laser scribing of polyimide film. This assembly provides a new approach to a smart patch through which release can be electronically controlled, allowing repetitive dosing. Rather than relying on passive diffusion, delivery is induced and terminated through the controlled heating of the PCM with transfer only occurring when the PCM transitions from solid to liquid. The material properties of the device and release characteristics of the strategy under repetitive dosing are critically assessed. The delivery yield of curcumin was found to be 3.5 µg (4.5 µg/cm²) per 3 min thermal cycle. Full article

Microfluidic-drop networks consist of several stable drops—interconnected through microfluidic channels—in which organ models can be cultured long-term. Drop networks feature a versatile configuration and an air–liquid interface (ALI). This ALI provides ample oxygenation, rapid liquid turnover, passive degassing, and liquid-phase stability through capillary pressure. Mathematical modeling, e.g., by using computational fluid dynamics (CFD), is a powerful tool to design drop-based microfluidic devices and to optimize their operation. Although CFD is the most rigorous technique to model flow, it falls short in terms of computational efficiency. Alternatively, the hydraulic–electric analogy is an efficient “first-pass” method to explore the design and operation parameter space of microfluidic-drop networks. However, there are no direct electric analogs to a drop, due to the nonlinear nature of the capillary pressure of the ALI. Here, we present a circuit-based model of hanging- and standing-drop compartments. We show a phase diagram describing the nonlinearity of the capillary pressure of a hanging drop. This diagram explains how to experimentally ensure drop stability. We present a methodology to find flow rates and pressures within drop networks. Finally, we review several applications, where the method, outlined in this paper, was instrumental in optimizing design and operation. Full article

Water contamination is a critical issue that threatens global public health. To enable the rapid and precise monitoring of pathogen contamination in drinking water, a concentration technique for bacterial cells is required to address the limitations of current detection methods, including the culture method and polymerase chain reaction. Here we present a viscoelastic microfluidic device for the continuous concentration of bacterial cells. To validate the device performance for cell concentration, the flow characteristics of 2-μm particles were estimated in viscoelastic fluids at different concentrations and flow rates. Based on the particle flow distributions, the flow rate factor, which is defined as the ratio of the inlet flow rate to the outlet flow rate at the center outlet, was optimized to achieve highly concentrated bacterial cells by removal of the additional suspending medium. The flow characteristics of 0.5-, 0.7-, and 1.0-μm-diameter particles were evaluated to consider the effect of a wide spectrum of bacterial size distribution. Finally, the concentration factor of bacterial cells, Staphylococcus aureus, suspended in a 2000-ppm polyethylene oxide solution was found to be 20.6-fold at a flow rate of 20 μL/min and a flow rate factor of 40. Full article

The development of robust bioanalytical devices and biosensors for infectious pathogens is progressing well with the advent of new materials, concepts, and technology. The progress is also stepping towards developing high throughput screening technologies that can quickly identify, differentiate, and determine the concentration of harmful pathogens, facilitating the decision-making process for their elimination and therapeutic interventions in large-scale operations. Recently, much effort has been focused on upgrading these analytical devices to an intelligent technological platform by integrating them with modern communication systems, such as the internet of things (IoT) and machine learning (ML), to expand their application horizon. This review outlines the recent development and applications of bioanalytical devices and biosensors to detect pathogenic microbes in environmental samples. First, the nature of the recent outbreaks of pathogenic microbes such as foodborne, waterborne, and airborne pathogens and microbial toxins are discussed to understand the severity of the problems. Next, the discussion focuses on the detection systems chronologically, starting with the conventional methods, advanced techniques, and emerging technologies, such as biosensors and other portable devices and detection platforms for pathogens. Finally, the progress on multiplex assays, wearable devices, and integration of smartphone technologies to facilitate pathogen detection systems for wider applications are highlighted. Full article

The anti-reflection properties of hard material surfaces are of great significance in the fields of infrared imaging, optoelectronic devices, and aerospace. Femtosecond laser processing has drawn a lot of attentions in the field of optics as an innovative, efficient, and green micro-nano processing method. The anti-reflection surface prepared on hard materials by femtosecond laser processing technology has good anti-reflection properties under a broad spectrum with all angles, effectively suppresses reflection, and improves light transmittance/absorption. In this review, the recent advances on femtosecond laser processing of anti-reflection surfaces on hard materials are summarized. The principle of anti-reflection structure and the selection of anti-reflection materials in different applications are elaborated upon. Finally, the limitations and challenges of the current anti-reflection surface are discussed, and the future development trend of the anti-reflection surface are prospected. Full article