With the depletion of fossil fuel energy and both the slow development and low utilization rate of new eco-friendly energy, finding new ways to efficiently store energy has become a research hotspot. Presently, polyethylene glycol (PEG) is an excellent heat storage material, but it is a typical solid-liquid phase change material (PCM) with a risk of leakage during phase transition. A combination of wood flour (WF) and PEG can effectively eliminate the risk of leakage after the melting of PEG. However, WF and PEG are both flammable materials, which impedes their application. Therefore, it is of great significance to expand their application by forming composites from among PEG, supporting mediums, and flame-retardant additives. This will improve both their flame retardancy and phase change energy storage performance, and will also lead to the preparation of excellent flame-retardant phase change composite materials with solid-solid phase change characteristics. To address this issue, ammonium polyphosphate (APP), organic modified montmorillonite (OMMT), and WF were blended into PEG in specific proportions to prepare a series of PEG/WF-based composites. Both thermal cycling tests and thermogravimetric analysis results demonstrated that the as-prepared composites had good thermal reliability and chemical stability. In addition, during differential scanning calorimetry tests, the PEG/WF/[email protected] composite presented the highest melting latent heat (176.6 J/g), and its enthalpy efficiency reached more than 98.3%. The PEG/WF/[email protected] composite also exhibited superior thermal insulation performance when compared to the pure PEG/WF composite. Furthermore, the PEG/WF/[email protected] composite exhibited a significant 50% reduction in peak heat release rate as a result of the synergistic effect between OMMT and APP in the gas and condensed phases. This work offers a useful strategy for the fabrication of multifunctional phase-change material, which is expected to broaden its industrial applications. Full article

This study investigated the impact of individual and combination of different sources of heating (passive solar heating, electric oil-heater, and solar air heater) in a pilot-scale building containing phase change material (PCM) for a potential reduction in energy consumption while maintaining thermal comfort. Unlike most of the recent simulations and modelling studies, this impact was tested experimentally using two identical control and test huts located at the University of Auckland. The control hut was equipped with standard gypsum boards while the test hut had gypsum boards containing PCM (PureTemp 20, PT20). The study found that combining both active and passive solar heating with a temperature-controlled electric oil heater demonstrated the ability to provide significant energy savings and maintain thermal comfort in the test hut, most notably overnight. The suggested combination was tested over different weather conditions and with different temperature constraints to maintain thermal comfort and achieve energy savings ranging from 33% to 87.5%. Full article

The Stefan problem regarding the formation of several liquid–solid interfaces produced by the oscillations of the ambient temperature around the melting point of a phase change material has been addressed by several authors. Numerical and semi-analytical methods have been used to find the thermal response of a phase change material under these type of boundary conditions. However, volume changes produced by the moving fronts and their effects on the thermal performance of phase change materials have not been addressed. In this work, volume changes are incorporated through an additional equation of motion for the thickness of the system. The thickness of the phase change material becomes a dynamic variable of motion by imposing total mass conservation. The modified equation of motion for each interface is obtained by coupling mass conservation with a local energy–mass balance at each front. The dynamics of liquid–solid interface configurations is analyzed in the transient and steady periodic regimes. Finite element and heat balance integral methods are used to verify the consistency of the solutions to the proposed model. The heat balance integral method is modified and adapted to find approximate solutions when two fronts collide, and the temperature profiles are not smooth. Volumetric corrections to the sensible and latent heat released (absorbed) are introduced during front formation, annihilation, and in the presence of two fronts. Finally, the thermal energy released by the interior surface is estimated through the proposed model and compared with the solutions obtained through models proposed by other authors. Full article

Two mass-accommodation methods are proposed to describe the melting of paraffin wax used as a phase-change material in a centrally heated annular region. The two methods are presented as models where volume changes produced during the phase transition are incorporated through total mass conservation. The mass of the phase-change material is imposed as a constant, which brings an additional equation of motion. Volume changes in a cylindrical unit are pictured in two different ways. On the one hand, volume changes in the radial direction are proposed through an equation of motion where the outer radius of the cylindrical unit is promoted as a dynamical variable of motion. On the other hand, volume changes along the axial symmetry axis of the cylindrical unit are proposed through an equation of motion, where the excess volume of liquid constitutes the dynamical variable. The energy–mass balance at the liquid–solid interface is obtained according to each method of conceiving volume changes. The resulting energy–mass balance at the interface constitutes an equation of motion for the radius of the region delimited by the liquid–solid interface. Subtle differences are found between the equations of motion for the interface. The differences are consistent with mass conservation and local mass balance at the interface. Stationary states for volume changes and the radius of the region delimited by the liquid–solid interface are obtained for each mass-accommodation method. We show that the relationship between these steady states is proportional to the relationship between liquid and solid densities when the system is close to the high melting regime. Experimental tests are performed in a vertical annular region occupied by a paraffin wax. The boundary conditions used in the experimental tests produce a thin liquid layer during a melting process. The experimental results are used to characterize the phase-change material through the proposed models in this work. Finally, the thermodynamic properties of the paraffin wax are estimated by minimizing the quadratic error between the temperature readings within the phase-change material and the temperature field predicted by the proposed model. Full article

Thermal energy storage units conventionally have the drawback of slow charging response. Thus, heat transfer enhancement techniques are required to reduce charging time. Using nanoadditives is a promising approach to enhance the heat transfer and energy storage response time of materials that store heat by undergoing a reversible phase change, so-called phase change materials. In the present study, a combination of such materials enhanced with the addition of nanometer-scale graphene oxide particles (called nano-enhanced phase change materials) and a layer of a copper foam is proposed to improve the thermal performance of a shell-and-tube latent heat thermal energy storage (LHTES) unit filled with capric acid. Both graphene oxide and copper nanoparticles were tested as the nanometer-scale additives. A geometrically nonuniform layer of copper foam was placed over the hot tube inside the unit. The metal foam layer can improve heat transfer with an increase of the composite thermal conductivity. However, it suppressed the natural convection flows and could reduce heat transfer in the molten regions. Thus, a metal foam layer with a nonuniform shape can maximize thermal conductivity in conduction-dominant regions and minimize its adverse impacts on natural convection flows. The heat transfer was modeled using partial differential equations for conservations of momentum and heat. The finite element method was used to solve the partial differential equations. A backward differential formula was used to control the accuracy and convergence of the solution automatically. Mesh adaptation was applied to increase the mesh resolution at the interface between phases and improve the quality and stability of the solution. The impact of the eccentricity and porosity of the metal foam layer and the volume fraction of nanoparticles on the energy storage and the thermal performance of the LHTES unit was addressed. The layer of the metal foam notably improves the response time of the LHTES unit, and a 10% eccentricity of the porous layer toward the bottom improved the response time of the LHTES unit by 50%. The presence of nanoadditives could reduce the response time (melting time) of the LHTES unit by 12%, and copper nanoparticles were slightly better than graphene oxide particles in terms of heat transfer enhancement. The design parameters of the eccentricity, porosity, and volume fraction of nanoparticles had minimal impact on the thermal energy storage capacity of the LHTES unit, while their impact on the melting time (response time) was significant. Thus, a combination of the enhancement method could practically reduce the thermal charging time of an LHTES unit without a significant increase in its size. Full article

The high intermittency of solar energy is still a challenge yet to be overcome. The use of thermal storage has proven to be a good option, with phase change materials (PCM) as very promising candidates. Nevertheless, PCM compounds have typically poor thermal conductivity, reducing their attractiveness for commercial uses. This paper demonstrates the viability of increasing the PCM effective thermal conductivity to industrial required values (around 4 W/m·K) by using metal wool infiltrated into the resin under vacuum conditions. To achieve this result, the authors used an inert resin, decoupling the specific PCM material selection from the enhancement effect of the metal wools. To ensure proper behavior of the metal wool under standard industrial environments at a broad range of temperatures, a set of analyses were performed at high temperatures and an inert atmosphere, presenting a thorough analysis of the obtained results. Full article

The use of adequate thermal energy storage (TES) systems is an efficient way to achieve thermal comfort in buildings reducing the cooling and heating demand. Besides, deploy phase change materials (PCM) to meet and enhance the TES needs is highly effective and widely studied. In this paper, a study of the degradation of two fatty acids is presented, capric and myristic acids, in order to evaluate whether their thermo-physical properties are affected throughout time during service. This was carried out by means of two different types of thermal treatments: degradation at constant temperature (thermal stability test), 60 °C during 100 h and 500 h, and degradation with heating and cooling cycling (thermal cycling stability), between a temperature range from 15 °C to 70 °C with 0.5 °C/min ramp during 500 and 1000 cycles. Despite no significant changes were measured for myristic acid, experimental results revealed a decrease of melting enthalpy of 6.6% in capric acid thermally treated for 500 h. Evidences of chemical degradation were found that might explain the decrease in thermophysical properties during use. Full article

Front tracking and enthalpy methods used to study phase change processes are based on a local thermal energy balance at the liquid–solid interface where mass accommodation methods are also used to account for the density change during the phase transition. Recently, it has been shown that a local thermal balance at the interface does not reproduce the thermodynamic equilibrium in adiabatic systems. Total thermal balance through the entire liquid–solid system can predict the correct thermodynamic equilibrium values of melted (solidified) mass, system size, and interface position. In this work, total thermal balance is applied to systems with isothermal–adiabatic boundary conditions to estimate the sensible and latent heat stored (released) by ${\mathrm{KNO}}_3$ and ${\mathrm{KNO}}_3/{\mathrm{NaNO}}_3$ salts which are used as high-temperature phase change materials. Relative percent differences between the solutions obtained with a local thermal balance at the interface and a total thermal balance for the thermal energy absorbed or released by high-temperature phase change materials are obtained. According to the total thermal balance proposed, a correction to the liquid–solid interface dynamics is introduced, which accounts for an extra amount of energy absorbed or released during the phase transition. It is shown that melting or solidification rates are modified by using a total thermal balance through the entire system. Finally, the numerical and semi-analytical methods illustrate that volume changes and the fraction of melted (solidified) solid (liquid) estimated through a local thermal balance at the interface are not invariant in adiabatic systems. The invariance of numerical and semi-analytical solutions in adiabatic systems is significantly improved through the proposed model. Full article

Environmental problems have been associated with energy consumption and waste management. A solution is the development of renewable materials such as organic phase change materials. Characterization of new materials allows knowing their applications and simulations provide an idea of how they can developed. Consequently, this research is focused on the thermal and chemical characterization of five different avocado seed oils depending on the maturity stage of the seed: 100% unripe, 25% mature-75% unripe, 50% mature-50% unripe, 75% mature-25% unripe, and 100% mature. The characterization was performed by differential scanning calorimetry, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The best oil for natural environments corresponded to 100% matured seed with an enthalpy of fusion of 52.93 $\mathrm{J}·{\mathrm{g}}^{-1}$, and a degradation temperature between 241–545 °C. In addition, the FTIR analysis shows that unripe seed oil seems to contain more lipids than a mature one. Furthermore, a simulation with an isothermal box was conducted with the characterized oil with an initial temperature of −14 °C for the isothermal box, −27 °C for the PCM box, and an ambient temperature of 25 °C. The results show that without the PCM the temperature can reach −8 °C and with it is −12 °C after 7 h, proving its application as a cold thermal energy system. Full article

Applying a well-performing heat exchanger is an efficient way to fortify the relatively low thermal response of phase-change materials (PCMs), which have broad application prospects in the fields of thermal management and energy storage. In this study, an improved PCM melting and solidification in corrugated (zigzag) plate heat exchanger are numerically examined compared with smooth (flat) plate heat exchanger in both horizontal and vertical positions. The effects of the channel width (0.5 W, W, and 2 W) and the airflow temperature (318 K, 323 K, and 328 K) are exclusively studied and reported. The results reveal the much better performance of the horizontal corrugated configuration compared with the smooth channel during both melting and solidification modes. It is found that the melting rate is about 8% faster, and the average temperature is 4 K higher in the corrugated region compared with the smooth region because of the large heat-exchange surface area, which facilitates higher rates of heat transfer into the PCM channel. In addition to the higher performance, a more compact unit can be achieved using the corrugated system. Moreover, applying the half-width PCM channel accelerates the melting rate by eight times compared to the double-width channel. Meanwhile, applying thicker channels provides faster solidification rates. The melting rate is proportional to the airflow temperature. The PCM melts within 274 s when the airflow temperature is 328 K. However, the melting time increases to 460 s for the airflow temperature of 308 K. Moreover, the PCM solidifies in 250 s and 405 s in the cases of 318 K and 328 K airflow temperatures, respectively. Full article

This study researches the effect of phase change materials (PCMs) containing carbonized rice husks (CRHs) in wood plastic composites (WPCs) as roof finishing materials on roof-surface and indoor temperatures. A cool roof miniature model was prepared, and measurements were taken using three fixed temperatures of 30 to 32 °C, 35 to 37 °C, and 40 to 42 °C. Sodium sulfate decahydrate (Na₂SO₄·10H₂O) and paraffin wax were selected as the PCMs. CRHs were used as additives to improve the thermal conductivities of the PCMs. At lower fixed temperatures such as 30 to 32 °C and 35 to 37 °C, the rates of increase of the surface temperatures of roofs containing CRHs with Na₂SO₄·10H₂O, and paraffin wax, were observed to gradually decrease compared to those of the roofs without PCMs. The indoor temperatures for the above-mentioned PCMs containing CRHs were maintained to be lower than those of the indoors without PCMs. Additionally, as the CRH content in the PCM increased, the rates of increase of the roof-surface and indoor temperatures decreased due to a faster roof heat absorption by PCMs through the improved thermal conductivity of CRHs. However, under higher artificial temperatures such as 40 to 42 °C, Na₂SO₄·10H₂O with CRHs exhibited no effect due to being out of latent heat range of Na₂SO₄·H₂O. For paraffin wax, as CRH content increased, their roof- surface and indoor temperatures decreased. Especially, the surface temperature of the roof containing paraffin contained 5 wt.% CRHs reduced by 11 °C, and its indoor temperature dropped to 26.4 °C. The thermal conductivity of PCM was enhanced by the addition of CRHs. A suitable PCM selection in each location can result in the reduction of the roof-surface and indoor temperatures. Full article

The construction and maintenance of building stock is responsible for approximately 36% of all CO₂ emissions in the European Union. One of the possibilities of how to achieve high energy-efficient and decarbonized building stock is the integration of renewable energy sources (RES) in building energy systems that contain efficient energy storage capacity. Phase Change Materials (PCMs) are latent heat storage media with a high potential of integration in building structures and technical systems. Their solid-liquid transition is specifically utilized for thermal energy storage in building applications. The typically quite old example is the use of ice that serves as long-term storage of cold. Large pieces of ice cut in winter were stored in heavily insulated spaces and prepared for cooling of food or beverages in summer. In the contemporary use of the principle, the PCMs for building applications and tested in this study must have a melting range close to the desired temperature in the occupied rooms. As the PCMs need to be encapsulated, several types of metal containers have been developed and tested for their thermal conductivity and resistance to mechanical damage, which enhances the performance of these so-called latent heat thermal energy storage (LHTES) systems. Long-term compatibility of metals with PCMs depends, i.e., on the elimination of an undesirable interaction between the metal and the specific PCM. Heat storage medium must be reliably sealed in a metal container, especially if the LHTES is integrated into systems where PCM leaks can negatively affect human health (e.g., domestic hot water tanks). The aim of this study is to evaluate the interactions between the selected commercially available organic (Linpar 17 and 1820) and inorganic (Rubitherm SP22 and SP25) PCMs and metals widely used for PCM encapsulation (aluminum, brass, carbon steel, and copper). The evaluation is based on the calculation of the corrosion rate (CR), and the gravimetric method is used for the determination of the weight variations of the metal samples. The results show good compatibility for all metals with organic PCMs, which is demonstrated by a mass loss as low as 2.1 mg in case of carbon steel immersed in Linpar 1820 for 12 weeks. The exposure of metals to organic PCMs also did not cause any visual changes on the surface except for darker stains, and tarnishing occurred on the copper samples. More pronounced changes were observed in metal samples immersed in inorganic PCMs. The highest CR values were calculated for carbon steel exposed to inorganic PCM Rubitherm SP25 (up to 13.897 mg·cm⁻²·year⁻¹). The conclusion of the study is that aluminum is the most suitable container material for the tested PCMs as it shows the lowest mass loss and minimal visual changes on the surface after prolonged exposure to the selected PCMs. Full article

Shape-stabilized phase change material (SSPCM) is a promising thermal energy storage material in energy-saving buildings. However, its flammability leads to a fire risk. The conventional bulk addition method has a limited flame-retardant effect. Herein, a series of surface coatings with various flame retardants were introduced to improve flame retardance of SSPCM. The results showed that all of the coatings had flame-retardant effects on SSPCM; In particular, the EG coating performed the best: the horizontal burning time was the longest, the limiting oxygen index was above 30%, the V0 classification was obtained, the peak heat release rate was sharply decreased from 1137.0 to 392.5 kW/m² and the burning process was prolonged with the least total smoke production. The flame-retardant mechanism was discussed. As paraffin easily evaporated from the SSPCM at a moderate temperature, it caused flames. After being surface coated, the EG-based coatings first hindered the volatilization of paraffin at a moderate temperature, then expanded and formed thick porous carbon layers at a high temperature to block the transfer of combustibles, oxygen and heat between the bulk and the environment. Therefore, the surface coating strategy achieved a desirable flame-retardant level with fewer flame retardants. Full article

Latent Heat Storage (LHS) with Phase-Change Materials (PCMs) represents a high energy density storage technology which could be applied in a variety of applications such as waste heat recovery and integration of renewable energy technologies in energy systems. To increase the sustainability of these storage solutions, PCMs have to be developed with particular regard to bio-origin and biodegradability. Triglycerides represent an interesting class of esters as the main constituents of animal and vegetable fats, with attractive thermal properties. In order to be used as PCMs, the thermal behaviour of triglycerides has to be fully understood, as in some cases they have been reported to show polymorphism and supercooling. This study assesses the suitability of triglycerides as PCMs by reviewing the literature published so far on their behaviour and properties. In particular, melting points, enthalpies of fusion, polymorphism, thermal conductivities, heat capacities and thermal cycling stabilities are considered, with a focus on LHS and thermal energy storage applications. In addition, the efforts conducted regarding modelling and the prediction of melting points and enthalpies based on chemical structures are summarized and assessed. Full article