Nanomaterials

Research

Jump to: Other

12 pages, 3265 KiB

Open AccessArticle

Graphene-Based Biosensors for Detection of Composite Vibrational Fingerprints in the Mid-Infrared Region

by Yijun Cai, Yanfen Hang, Yuanguo Zhou, Jinfeng Zhu, Jingwen Yang and Xuanyu Wang

Nanomaterials 2019, 9(10), 1496; https://0-doi-org.brum.beds.ac.uk/10.3390/nano9101496 - 20 Oct 2019

Cited by 9 | Viewed by 2928

Abstract

In this study, a label-free multi-resonant graphene-based biosensor with periodic graphene nanoribbons is proposed for detection of composite vibrational fingerprints in the mid-infrared range. The multiple vibrational signals of biomolecules are simultaneously enhanced and detected by different resonances in the transmission spectrum. Each [...] Read more.

In this study, a label-free multi-resonant graphene-based biosensor with periodic graphene nanoribbons is proposed for detection of composite vibrational fingerprints in the mid-infrared range. The multiple vibrational signals of biomolecules are simultaneously enhanced and detected by different resonances in the transmission spectrum. Each of the transmission dips can be independently tuned by altering the gating voltage applied on the corresponding graphene nanoribbon. Geometric parameters are investigated and optimized to obtain excellent sensing performance. Limit of detection is also evaluated in an approximation way. Besides, the biosensor can operate in a wide range of incident angles. Electric field intensity distributions are depicted to reveal the physical insight. Moreover, another biosensor based on periodic graphene nanodisks is further proposed, whose performance is insensitive to the polarization of incidence. Our research may have a potential for designing graphene-based biosensor used in many promising bioanalytical and pharmaceutical applications. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures

Figure 1

16 pages, 650 KiB

Open AccessArticle

Impedance Model of Cylindrical Nanowires for Metamaterial Applications

by Mehboob Alam, Ali Mahmood, Shahida Azam, Madiha Saher Butt, Anwar Ul Haq and Yehia Massoud

Nanomaterials 2019, 9(8), 1104; https://0-doi-org.brum.beds.ac.uk/10.3390/nano9081104 - 01 Aug 2019

Cited by 8 | Viewed by 2715

Abstract

In metamaterials, metallic nanowires are used for creating artificial materials to functionalize them for various nanophotonics applications. Strong polarization-dependent response coupled with complex dielectric function at optical frequencies gives additional degrees of freedom to achieve scattering, absorption, and other benefits that go much [...] Read more.

In metamaterials, metallic nanowires are used for creating artificial materials to functionalize them for various nanophotonics applications. Strong polarization-dependent response coupled with complex dielectric function at optical frequencies gives additional degrees of freedom to achieve scattering, absorption, and other benefits that go much beyond what is possible with conventional materials. In this paper, we propose an extended cylindrical wave impedance approach at optical frequencies to model the internal and external impedance of the metallic nanowire. Equivalent analytical expression for the scattering, extinction, and absorption cross-sectional area efficiencies are derived in terms of impedances. The motivation is to develop an all-mode solution (

{TM}_{n}

and

{TE}_{n}

modes), by bringing the complex problem of plasmonic nanowire to linear system theory, where established methods can be applied to enable new applications. The equivalence of the impedance solution is compared with electromagnetic field solution and numerical full-wave field simulations. The proposed solution is accurate and may contribute to the rapid and efficient future designs for the metallic nanowire-based nanophotonic metamaterials. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures

Figure 1

14 pages, 3823 KiB

Open AccessArticle

A Comparison Study of Functional Groups (Amine vs. Thiol) for Immobilizing AuNPs on Zeolite Surface

by Xi Rao, Michaël Tatoulian, Cédric Guyon, Stephanie Ognier, Chenglin Chu and Ali Abou Hassan

Nanomaterials 2019, 9(7), 1034; https://0-doi-org.brum.beds.ac.uk/10.3390/nano9071034 - 19 Jul 2019

Cited by 24 | Viewed by 6042

Abstract

Immobilization of gold nanoparticles (AuNPs) on the surface of zeolite has received a great interest due to Au@zeolite’s unique characteristics and high performance for catalysis. In this work we studied the grafting of two different functional molecules; one having an amine group (3-aminopropyl)triethoxysilane [...] Read more.

Immobilization of gold nanoparticles (AuNPs) on the surface of zeolite has received a great interest due to Au@zeolite’s unique characteristics and high performance for catalysis. In this work we studied the grafting of two different functional molecules; one having an amine group (3-aminopropyl)triethoxysilane (APTES) and the second having a thiol group (3-mercaptopropyl)trimethoxysilane (MPTES) on the surface of zeolite using the same wet chemistry method. The modified zeolite surfaces were characterized using zeta potential measurements; diffuse reflectance infrared fourier transform (DRIFT) and X-ray photoelectron spectroscopy (XPS). The results confirmed a successful deposition of both functional groups at the topmost surface of the zeolite. Furthermore; transmission electron microscopy (TEM), ultraviolet-visible (UV-Vis) spectroscopy and XPS results clearly evidenced that APTES provided a better AuNPs immobilization than MPTES as a result of; (1) less active functions obtained after MPTES deposition, and (2) the better attaching ability of thiol to the gold surface. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures

Graphical abstract

9 pages, 1824 KiB

Open AccessArticle

Metal Slot Color Filter Based on Thin Air Slots on Silver Block Array

by Youngsoo Kim, Kihwan Moon, Young Jin Lee, Seokhyeon Hong and Soon-Hong Kwon

Nanomaterials 2019, 9(6), 912; https://0-doi-org.brum.beds.ac.uk/10.3390/nano9060912 - 25 Jun 2019

Viewed by 3069

Abstract

The human eye perceives the color of visible light depending on the spectrum of the incident light. Hence, the ability of color expression is very important in display devices. For practical applications, the transmitted color filter requires high transmittance and vivid colors, covering [...] Read more.

The human eye perceives the color of visible light depending on the spectrum of the incident light. Hence, the ability of color expression is very important in display devices. For practical applications, the transmitted color filter requires high transmittance and vivid colors, covering full standard default color spaces (sRGB). In this paper, we propose a color filter with a silver block array on a silica substrate structure with nanoscale air slots where strong transmission is observed through the slots between silver blocks. We investigated the transmitted color by simulating the transmission spectra as functions of various structure parameters. The proposed structure with an extremely small pixel size of less than 300 nm covers 90% of sRGB color depending on the structure and has a narrow angular distribution of transmitted light. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures

Figure 1

20 pages, 4779 KiB

Open AccessArticle

Reducing the Crystallite Size of Spherulites in PEO-Based Polymer Nanocomposites Mediated by Carbon Nanodots and Ag Nanoparticles

by Ranjdar M. Abdullah, Shujahadeen B. Aziz, Soran M. Mamand, Aso Q. Hassan, Sarkawt A. Hussein and M. F. Z. Kadir

Nanomaterials 2019, 9(6), 874; https://0-doi-org.brum.beds.ac.uk/10.3390/nano9060874 - 09 Jun 2019

Cited by 49 | Viewed by 4291

Abstract

The PEO-based polymer nanocomposites were prepared by solution cast method. Green approaches were used for synthesis of carbon nanodots (CNDs) and silver nanoparticles (Ag NPs). It was found that the crystallite size of spherulites of PEO was greatly scarified upon incorporation of CNDs [...] Read more.

The PEO-based polymer nanocomposites were prepared by solution cast method. Green approaches were used for synthesis of carbon nanodots (CNDs) and silver nanoparticles (Ag NPs). It was found that the crystallite size of spherulites of PEO was greatly scarified upon incorporation of CNDs and Ag NPs. In the present work, in opposition to other studies, broadening of surface plasmon resonance (SPR) peak of metallic Ag NPs in PEO-based polymer composites was observed rather than peak tuning. Various techniques, such as powder X-ray diffraction (XRD), SEM, UV–Vis spectroscopy, and photoluminescence (PL), were used to characterize the structural, morphological, and optical properties of the samples. Increase of amorphous phase for the PEO doped with CND particles was shown from the results of XRD analyses. Upon the addition of suspended Ag NPs to the PEO:CNDs composites, significant change of XRD peak position was seen. A field-emission scanning electron microscope (FESEM) was used to investigate the surface morphology of the samples. In the SEM, a significant change in the crystalline structure was seen. The size of PEO spherulites in the PEO nanocomposite samples became smaller and the percentage of amorphous portion became larger, owing to the distribution of CNDs and Ag NPs. The UV–Vis absorption spectra of the PEO-based polymer were found to improve and shift to higher wavelengths upon incorporation of CNDs and Ag NPs into the PEO matrix. The SPR peak broadening in the UV–Vis spectra was observed in the PEO:CNDs composites due to the Ag NPs. The absorption edge value of PEO was found to shift toward lower photon energy as the CNDs and Ag NPs are introduced. The photoluminescence (PL) spectra were also observed for the PEO:CNDs and PEO:CNDs:Ag samples and found to be more intense in the PEO:CNDs system than in the PEO:CNDs:Ag system. Lastly, the optical band gap of the samples was further studied in detail using of Tauc’s model and optical dielectric loss parameter. The types of electron transition were specified. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures

Graphical abstract

11 pages, 5317 KiB

Open AccessCommunication

Facile Photochemical Syntheses of Conjoined Nanotwin Gold-Silver Particles within a Biologically-Benign Chitosan Polymer

by Daniel K. Korir, Bharat Gwalani, Abel Joseph, Brian Kamras, Ravi K. Arvapally, Mohammad A. Omary and Sreekar B. Marpu

Nanomaterials 2019, 9(4), 596; https://0-doi-org.brum.beds.ac.uk/10.3390/nano9040596 - 11 Apr 2019

Cited by 15 | Viewed by 3240

Abstract

A simple photochemical method for making conjoined bi-metallic gold-silver (Au/Ag) nanotwins, a new breed of nanoparticles (NPs), is developed. To the best of our knowledge, the photochemical method resulted in distinct, conjoined, bimetallic nanotwins that are different from any well-established alloyed or core-shell [...] Read more.

A simple photochemical method for making conjoined bi-metallic gold-silver (Au/Ag) nanotwins, a new breed of nanoparticles (NPs), is developed. To the best of our knowledge, the photochemical method resulted in distinct, conjoined, bimetallic nanotwins that are different from any well-established alloyed or core-shell nanostructures in the literature. The conjoined Au-Ag NPs possessed surface plasmon resonance (SPR) properties of both metals. The bimetallic nanostructures possessing distinctive optical properties of both metals were obtained using Au NPs as seeds in the first step, followed by the addition of a silver precursor as feed in the second step during a photochemical irradiation process. In the first step, small, isotropic or large, anisotropic Au NPs are generated by photoinduced reduction within a biocompatible chitosan (CS) polymer. In the second step, a silver precursor (AgNO₃) is added as the feed to the AuNPs seed, followed by irradiation of the solution in the ice-bath. The entire photochemical irradiation process resulting in the formation of bimetallic Au-AgNPs did not involve any other reducing agents or stabilizing agents other than the CS polymer stabilizer. The small, conjoined Au-Ag bi-metallic NPs exhibited SPR with peak maxima centering at ~400 nm and ~550 nm, whereas the large conjoined nanoparticles exhibited SPR with peak maxima centering at ~400 nm, 550 nm, and 680 nm, characteristic of both gold and silver surface plasmons in solution. The tunability in the SPR and size of the bimetallic NPs were obtained by varying the reaction time and other reaction parameters, resulting in average sizes between 30 and 100 nm. The SPR, size, distribution, and elemental composition of the bi-metallic NPs were characterized using UV-Vis absorption, electron microscopy, and energy dispersive X-ray spectroscopy (EDS) studies. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures

Graphical abstract

10 pages, 1554 KiB

Open AccessArticle

Polarization Controllable Device for Simultaneous Generation of Surface Plasmon Polariton Bessel-Like Beams and Bottle Beams

by Peizhen Qiu, Taiguo Lv, Yupei Zhang, Binbin Yu, Jiqing Lian, Ming Jing and Dawei Zhang

Nanomaterials 2018, 8(12), 975; https://0-doi-org.brum.beds.ac.uk/10.3390/nano8120975 - 26 Nov 2018

Cited by 14 | Viewed by 2804

Abstract

Realizing multiple beam shaping functionalities in a single plasmonic device is crucial for photonic integration. Both plasmonic Bessel-like beams and bottle beams have potential applications in nanophotonics, particularly in plasmonic based circuits, near field optical trapping, and micro manipulation. Thus, it is very [...] Read more.

Realizing multiple beam shaping functionalities in a single plasmonic device is crucial for photonic integration. Both plasmonic Bessel-like beams and bottle beams have potential applications in nanophotonics, particularly in plasmonic based circuits, near field optical trapping, and micro manipulation. Thus, it is very interesting to find new approaches for simultaneous generation of surface plasmon polariton Bessel-like beams and bottle beams in a single photonic device. Two types of polarization-dependent devices, which consist of arrays of spatially distributed sub-wavelength rectangular slits, are designed. The array of slits are specially arranged to construct an X-shaped or an IXI-shaped array, namely X-shaped device and IXI-shaped devices, respectively. Under illumination of circularly polarized light, plasmonic zero-order and first-order Bessel-like beams can be simultaneously generated on both sides of X-shaped devices. Plasmonic Bessel-like beam and bottle beam can be simultaneously generated on both sides of IXI-shaped devices. By changing the handedness of circularly polarized light, for both X-shaped and IXI-shaped devices, the positions of the generated plasmonic beams on either side of device can be dynamically interchanged. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures

Graphical abstract

Other

Jump to: Research

11 pages, 5194 KiB

Open AccessLetter

Refractory Ultra-Broadband Perfect Absorber from Visible to Near-Infrared

by Huixuan Gao, Wei Peng, Shuwen Chu, Wenli Cui, Zhi Liu, Li Yu and Zhenguo Jing

Nanomaterials 2018, 8(12), 1038; https://0-doi-org.brum.beds.ac.uk/10.3390/nano8121038 - 12 Dec 2018

Cited by 85 | Viewed by 3939

Abstract

The spectral range of solar radiation observed on the earth is approximately 295 to 2500 nm. How to widen the absorption band of the plasmonic absorber in this range has become a hot issue in recent years. In this paper, we propose a [...] Read more.

The spectral range of solar radiation observed on the earth is approximately 295 to 2500 nm. How to widen the absorption band of the plasmonic absorber in this range has become a hot issue in recent years. In this paper, we propose a highly applicable refractory perfect absorber with an elliptical titanium nanodisk array based on a silica–titanium–silica–titanium four-layer structure. Through theoretical design and numerical demonstration, the interaction of surface plasmon resonance with the Fabry–Perot cavity resonance results in high absorption characteristics. Our investigations illustrate that it can achieve ultra-broadband absorption above 90% from a visible 550-nm wavelength to a near-infrared 2200-nm wavelength continuously. In particular, a continuous 712-nm broadband perfect absorption of up to 99% is achieved from wavelengths from 1013 to 1725 nm. The air mass 1.5 solar simulation from a finite-difference time domain demonstrates that this absorber can provide an average absorption rate of 93.26% from wavelengths of 295 to 2500 nm, which can absorb solar radiation efficiently on the earth. Because of the high melting point of Ti material and the symmetrical structure of this device, this perfect absorber has excellent thermal stability, polarization independence, and large incident-angle insensitivity. Hence, it can be used for solar cells, thermal emitters, and infrared detection with further investigation. Full article

(This article belongs to the Special Issue Plasmonic Nanostructures and Related Applications)

► Show Figures